DLA A-A-59429-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END 120 DEG COUNTERSUNK HEAD ALUMINUM ALLOY CARBON STEEL NICKEL-COPPER ALLOY《铝合金制200度开口端型限动芯棒用非结构性埋头盲铆钉》.pdf

《DLA A-A-59429-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END 120 DEG COUNTERSUNK HEAD ALUMINUM ALLOY CARBON STEEL NICKEL-COPPER ALLOY《铝合金制200度开口端型限动芯棒用非结构性埋头盲铆钉》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59429-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END 120 DEG COUNTERSUNK HEAD ALUMINUM ALLOY CARBON STEEL NICKEL-COPPER ALLOY《铝合金制200度开口端型限动芯棒用非结构性埋头盲铆钉》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 5 FSC 5320DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-5942920 APRIL 1999COMMERCIAL ITEM DESCRIPTIONRIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL,OPEN END, 120O COUNTERSUNK HEAD, ALUMINUM ALLOY, CARBON STEEL, NICKEL-COPPERALLOYThis Gen

2、eral Services Administration has authorized the use of this Commercial Item Description for allFederal agencies.1. SCOPE: This Commercial Item Description (CID) covers the requirements for pull-stem expandable blindrivets. These rivets are intended for rapid and permanent non-structural fastening ap

3、plications in which access isavailable to one side only.2. SALIENT CHARACTERISTICS:2.1 Blind rivets furnished under this CID shall conform to the materials, strengths, and dimensions as specified inTable I, II, and III and as shown in Figure 1 below.FIGURE 1. RIVETSBENEFICIAL COMMENTS, RECOMMENDATIO

4、NS, ADDITIONS, DELETIONS, CLARIFICATIONS,ETC., AND DATA WHICH MAY IMPROVE THIS DOCUMENT SHOULD BE SENT TO: DEFENSEINDUSTRIAL SUPPLY CENTER, ATTN: DISC-AEEB, 700 ROBBINS AVENUE, PHILADELPHIA, PA19111-5096.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

5、,-A-A-594292TABLE I. MATERIAL COMBINATION SYMBOLS AND STRENGTHSSYMBOL MATERIAL COMBINATION RIVETDIAMINIMUMSHEARLOADLBSMINIMUMTENSIONLOADLBSA Body: 5056 Al Alloy(UNS A95056)Mandrel: 1006-1038 Steel(UNS G10060-G10380).125.156.188170260380220350500B Body: 5052 Al Alloy(UNS A95052)Mandrel: 2024 Al Alloy

6、(UNS A92024).125 120 150D Body: 1006-1010 Steel(UNS G10060-G10100)Mandrel: 1030-1060 Steel(UNS G10300-G10600).125 260 310EBody: Nickel Copper Alloy(UNS N04400)Mandrel: 1030-1060 Steel(UNS G10300-G10600).125.156.1883505508004507001000TABLE II. BASIC DIMENSIONSBASIC DIMENSIONSNOMDIA D HEREFRMAXWNOMFMA

7、XPMINRECOMMENDEDHOLE SIZE.094 .096.090.187.161.027 .020 .057 L+.100 1.00 .097-.100.125 .128.122.233.207.031 .025 .076 L+.120 1.00 .129-.133.156 .159.153.294.268.040 .030 .095 L+.140 1.06 .160-.164.188 .191.183.361.335.050 .035 .114 L+.160 1.06 .192-.196Provided by IHSNot for ResaleNo reproduction or

8、 networking permitted without license from IHS-,-,-A-A-594293TABLE III. DASH NUMBERS AND DIMENSIONSDASH NUMBERA B D ELMAXRECOMMENDEDGRIP RANGEA302A304 B304D302D304.250.375.079-.125.126-.250A401A402A403A404A405A406B401B402B403B404B405B406D402D403D404D405D406E401E402E403E404E405.203.275.337.400.462.52

9、5.040-.062.063-.125.126-.187.188-.250.251-.312.313-.375A502A503A504A506A508B502B503B504B506B508D502D503D504D506D508E502E503E504E506.290.362.425.550.675.063-.125.120-.187.188-.250.251-.375.376-.500A602A604A606A608A610A612B602B604B606B608B610D602D604D606D608D610E602E604E606E608E610.315.450.575.700.825

10、.950.063-.125.126-.250.251-.375.376-.500.501-.625.626-.750Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5942942.2 Materials shall be of the type and grade specified in Table I.2.3 Surface finish.2.3.1 Aluminum alloy rivets shall be furnished ei

11、ther chemically treated in accordance with MIL-C-5541, oranodically treated in accordance with MIL-A-8625 at the suppliers option2.3.2 Carbon steel bodies shall be zinc plated in accordance with ASTM B633, Type II, FE/ZN5 or phosphatecoated in accordance with Type Z, Class 2 or 4B of DOD-P-16232. Ca

12、rbon steel mandrels shall be zinc plated orphosphate coated.2.3.3. Nickel-Copper Alloy bodies shall be zinc plated in accordance with ASTM B633, Type II, FE/ZN5.2.4 Workmanship. Rivets shall be of uniform quality and free from injurious seams and other injurious defects.2.5 Single shear load. The sh

13、ear test shall be performed in accordance with Test Method 20 of NASM1312, orequivalent and shall conform to the data specified in Table I.2.6 Tension load. The tension test shall be performed in accordance with Test Method 8 of NASM1312, orequivalent and shall conform to the data specified in Table

14、 I.2.7 Packaging requirements The requirements for packaging shall be in accordance with ASTM D3951.3. QUALITY ASSURANCE PROVISIONS.3.1 Product conformance. The products provided shall meet the salient characteristics of this commercial itemdescription, conform to the producers own drawings, specifi

15、cations, standards, and the quality assurance practices,and be the same product offered for sale in the commercial market. The government reserves the right to requireproof of such conformance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59429

16、54. NOTES4.1 All dimensions are in inches.4.2 The part number shall consist of the basic Commercial Item Description Number followed by a dash numberfrom Table III. The dash number consists of a material combination symbol from Table I, a nominal bodydiameter size code in thirty-seconds of an inch f

17、rom Table II, and a maximum grip code in sixteenths of an inchfrom Table III.EXAMPLE: AA59429 A 5 03Grip Range CodeNominal DiameterMaterialCommercial Item Description NumberAA59429A503 Indicates - Rivet, blind, nonstructural, retainedmandrel, open-end, 120o countersunk head,5056 (UNS A95056) aluminu

18、m alloy body,C1006-C1038 (UNS G10060-G10380) steelmandrel; nominal body diameter size, .156;grip range, .120-.187.Military Interests:Custodians: Preparing Activity:Army - AR DLA-ISNavy - ASAir Force - 99Review Activities: (Project No. 5320-0958)Army - AV, MIAir Force - 11, 82National Security Agency

19、-NSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3 and 8. In block 1, both the document number and revision letter should be given.2. The

20、submitter of this form must complete blocks 4, 5, 6 and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of documents, or to request waivers, or clarification of requirements on current contracts.Comments submi

21、tted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-594292. DOCUMENT DATE (YYMMDD)9904203. DOCUMENT TITLE:RIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL, OPEN END, 120O COUNT

22、ERSUNK HEAD, ALUMINUMALLOY, CARBON STEEL, NICKEL-COPPER ALLOY4. NATURE OF CHANGE5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(2) AUTOVON (If applicable)7. DATE SUBMITTED (YYMMD

23、D)8. PREPARING ACTIVITY DLA-ISa. NAMEEmelia Altomarib. TELEPHONE (Include Area Code)(1) Commercial (215) 697-6827(2) (DSN) 442-6827c. ADDRESS (Include Zip Code)Defense Industrial Supply Center700 Robbins AvenueBldg. 3 (Code DISC-AESD)Philadelphia, PA 19111-5096IF YOU DO NOT RECEIVE A REPLY WITHIN 45

24、 DAYS, CONTACT:Defense Quality and Standardization Office5203 Leesburg Pike, Suite 1403Falls Church, VA 22041TELEPHONE (703) 756-2340 AUTOVON 289-2340DD Form 1426, OCT 89 Previous editions are obsolete. 198/290Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-