DLA A-A-59427-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END LARGE DOMED HEAD ALUMINUM ALLOY CARBON STEEL《碳素钢 铝合金制大球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf

《DLA A-A-59427-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END LARGE DOMED HEAD ALUMINUM ALLOY CARBON STEEL《碳素钢 铝合金制大球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59427-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END LARGE DOMED HEAD ALUMINUM ALLOY CARBON STEEL《碳素钢 铝合金制大球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 4 FSC5320DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-5942720 APRIL 1999COMMERCIAL ITEM DESCRIPTIONRIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL,OPEN END, LARGE DOMED HEAD, ALUMINUM ALLOY, CARBON STEELThis General Services Administrati

2、on has authorized the use of this Commercial Item Description forall Federal agencies.1. SCOPE: This Commercial Item Description (CID) covers the requirements for pull-stem expandable blindrivets. These rivets are intended for rapid and permanent non-structural fastening applications in which access

3、is available to one side only.2. SALIENT CHARACTERISTICS:2.1 Blind rivets furnished under this CID shall conform to the materials, strengths, and dimensions as specified inTable I, II, and III and as shown in Figure 1 below.FIGURE 1. RIVETSBENEFICIAL COMMENTS, RECOMMENDATIONS, ADDITIONS, DELETIONS,

4、CLARIFICATIONS,ETC., AND DATA WHICH MAY IMPROVE THIS DOCUMENT SHOULD BE SENT TO: DEFENSEINDUSTRIAL SUPPLY CENTER, ATTN: DISC-AEEB, 700 ROBBINS AVENUE, PHILADELPHIA, PA19111-5096.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594272TABLE I. MATER

5、IAL COMBINATION SYMBOLS AND STRENGTHSSYMBOL MATERIAL COMBINATION RIVETDIAMINIMUMSHEARLOADLBSMINIMUMTENSIONLOADLBSA Body: 5056 Al Alloy(UNS A95056)Mandrel: 1006-1038 Steel(UNS G10060-G10380).125.188170380220500B Body: 5052 Al Alloy(UNS A95052)Mandrel: 2024 Al Alloy(UNS A92024).125.188120260150320D Bo

6、dy: 1006-1010 Steel(UNS G10060-G10100)Mandrel: 1030-1038 Steel(UNS G10300-G10380).125.188260540310680TABLE II. BASIC DIMENSIONSBASIC DIMENSIONSNOMDIA.SIZECODENOMDIA D H ERMAXWNOMFMAXPMINRECOMMENDEDHOLE SIZE4 .125 .128.122.390.360.065.034.020 .076 L MAX+ .1201.00 .129-.1336 .188 .191.183.650.600.092.

7、067.025 .114 L MAX+.1601.00 .192-.196Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594273TABLE III. DASH NUMBERS AND DIMENSIONSDASH NUMBERA B D L RECOMMENDEDGRIP RANGEA402A404A406A408B402B404B406B408D402D404D406D408.235-.275.360-.400.485-.535.6

8、10-.670.063-.125.188-.250.313-.375.376-.500 1/A504A506A508B504B506B508D504D506D508.385-.425.510-.550.635-.695.188-.250.251-.375.376-.500A606A608A610A612B606B608B610B612D606D608D610D612.535-.575.660-.700.785-.850.910-.980.251-.375.376-.500.501-.625.626-.7501/ When applicable, supplier may provide a d

9、ash 407, with a grip range of .376-.437.2.2 Materials shall be of the type and grade specified in Table I.2.3 Surface finish.2.3.1 Carbon steel mandrels shall be zinc plated or phosphate coated.2.3.2 Aluminum alloy rivets shall be furnished either chemically treated or anodically treated at the supp

10、liersoption2.4 Workmanship. Rivets shall be of uniform quality and free from injurious seams and other injurious defects.2.5 Single shear load. The shear test shall be performed in accordance with Test Method 20 of MIL-STD-1312,or equivalent and shall conform to the data specified in Table I.2.6 Ten

11、sion load. The tension test shall be performed in accordance with Test Method 8 of MIL-STD-1312, orequivalent and shall conform to the data specified in Table I.2.7 Packaging requirements The requirements for packaging shall be in accordance with ASTM D3951.3. QUALITY ASSURANCE PROVISIONS.3.1 Produc

12、t conformance. The products provided shall meet the salient characteristics of this commercial itemdescription, conform to the producers own drawings, specifications, standards, and the quality assurance practices,and be the same product offered for sale in the commercial market. The government rese

13、rves the right to requireproof of such conformance.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5942744. NOTES4.1 All dimensions are in inches.4.2 The part number shall consist of the basic Commercial Item Description Number followed by a dash

14、 numberfrom Table III. The dash number consists of a material combination symbol from Table I, a nominal bodydiameter size code from Table II, and a grip range code from Table III.EXAMPLE: AA59427 B 6 06GripNominal diameterMaterialCommercial Item Description NumberAA59427B606 Indicates - Rivet, blin

15、d, nonstructural, retainedmandrel, open-end, domed head, 5052(UNS A95052) aluminum alloy body, 2024(UNS A92024) aluminum alloy mandrel;nominal body diameter size, .188;grip range, .251-.375.Military Interests:Custodians: Preparing Activity:Army - AR DLA-ISNavy - ASAir Force - 99Review Activities: (P

16、roject No. 5320-0956)Army - AV, MIAir Force - 11, 82National Security Agency-NSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3 and 8. In b

17、lock 1, both the document number and revision letter should be given.2. The submitter of this form must complete blocks 4, 5, 6 and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of documents, or to request w

18、aivers, or clarification of requirements on current contracts.Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-594272. DOCUMENT DATE (YYMMDD)9904203. DOCUMEN

19、T TITLE:RIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL, OPEN END, LARGE DOMED HEAD, ALUMINUMALLOY, CARBON STEEL4. NATURE OF CHANGE5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(

20、2) AUTOVON (If applicable)7. DATE SUBMITTED (YYMMDD)8. PREPARING ACTIVITY DLA-ISa. NAMEEmelia Altomarib. TELEPHONE (Include Area Code)(1) Commercial (215) 697-6827(2) (DSN) 442-6827c. ADDRESS (Include Zip Code)Defense Industrial Supply Center700 Robbins AvenueBldg. 3 (Code DISC-AESD)Philadelphia, PA

21、 19111-5096IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT:Defense Quality and Standardization Office5203 Leesburg Pike, Suite 1403Falls Church, VA 22041TELEPHONE (703) 756-2340 AUTOVON 289-2340DD Form 1426, OCT 89 Previous editions are obsolete. 198/290Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-