DLA A-A-59425-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END DOMED HEAD ALUMINUM ALLOY CARBON STEEL CORROSION RESISTANT STEEL《不锈钢 碳素钢 铝合金制球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf

《DLA A-A-59425-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END DOMED HEAD ALUMINUM ALLOY CARBON STEEL CORROSION RESISTANT STEEL《不锈钢 碳素钢 铝合金制球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59425-1999 RIVETS BLIND NONSTRUCTURAL RETAINED MANDREL OPEN END DOMED HEAD ALUMINUM ALLOY CARBON STEEL CORROSION RESISTANT STEEL《不锈钢 碳素钢 铝合金制球形圆柱式开口端型限动芯棒用非结构性盲铆钉》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 4 FSC 5320DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-5942520 APRIL 1999COMMERCIAL ITEM DESCRIPTIONRIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL,OPEN END, DOMED HEAD, ALUMINUM ALLOY,CARBON STEEL, CORROSION RESISTANT STEELThis General

2、Services Administration has authorized the use of this Commercial Item Description for all Federal agencies.1. SCOPE: This Commercial Item Description (CID) covers the requirements for pull-stem expandable blindrivets. These rivets are intended for rapid and permanent non-structural fastening applic

3、ations in which access isavailable to one side only.2. SALIENT CHARACTERISTICS:2.1 Blind rivets furnished under this CID shall conform to the materials, strengths, and dimensions as specified inTable I, II, and III and as shown in Figure 1 below.FIGURE 1. RIVETSBENEFICIAL COMMENTS, RECOMMENDATIONS,

4、ADDITIONS, DELETIONS, CLARIFICATIONS,ETC., AND DATA WHICH MAY IMPROVE THIS DOCUMENT SHOULD BE SENT TO: DEFENSEINDUSTRIAL SUPPLY CENTER, ATTN: DISC-AEEB, 700 ROBBINS AVENUE, PHILADELPHIA, PA19111-5096.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-

5、A-594252TABLE I. MATERIAL COMBINATION SYMBOLS AND STRENGTHSSYMBOL MATERIAL COMBINATION RIVETDIAMINIMUMSHEARLOADLBSMINIMUMTENSIONLOADLBSABody: 5056 Al Alloy(UNS A95056)Mandrel: 1006-1038 Steel(UNS G10060-G10380).094.125.156.188.25090170260380700120220350500920BBody: 5052 Al Alloy(UNS A95052)Mandrel:

6、2024 Al Alloy(UNS A92024).094.125.156.188.2507012019026046080150230320560DBody: 1006-1010 Steel(UNS G10060-G10100)Mandrel: 1030-1060 Steel(UNS G10300-G10600).094.125.156.188.25013026037054010001703104706801240FBody: 302 CRES (UNS S30200)302-HQ-CRES (UNS S30430)304 CRES (UNS S30400)305 CRES (UNS S305

7、00)Mandrel: 304 CRES (UNS S30400)305-431 CRES(UNS S30500-S43100).094.125.156.188.250230420650950170028053082012002100GBody: 302 CRES (UNS S30200)302-HQ-CRES (UNS S30430)304 CRES (UNS S30400)305 CRES (UNS S30500)Mandrel: 1030-1060 Steel(UNS G10300-G10600).094.125.156.188.25023042065095017002805308201

8、2002100TABLE II. BASIC DIMENSIONSBASIC DIMENSIONSNOMDIA.SIZECODENOMDIA D H ERMAXWNOMFMAXPMINRECOMMENDEDHOLE SIZE3 .094 .096.090.198.178.032.022.015 .057 L MAX+ .1001.00 .097-.1004 .125 .128.122.262.238.040.030.020 .076 L MAX+ .1201.00 .129-.1335 .156 .159.153.328.296.050.037.020 .095 L MAX+.1401.00

9、.160-.1646 .188 .191.183.394.356.060.045.0251/.114 L MAX+.1601.00 .192-.1968 .250 .255.246.525.475.080.065.0302/.151 L MAX+.1801. 00 .257-.2611/ For material combinations F and G, R Max shall be 0.035.2/ For material combinations F and G, R Max shall be 0.060.Provided by IHSNot for ResaleNo reproduc

10、tion or networking permitted without license from IHS-,-,-A-A-594253TABLE III. DASH NUMBERS AND DIMENSIONSDASH NUMBERSL RECOMMENDEDA B D F G MAX GRIP RANGEA302A304B302B304B306D302D304F302F304G302G304.250.375.500.032-.125.126-.250.251-.375A401A402A403A404A405B401B402B403B404B405D401D402D403D404D405F4

11、02F403F404G402G403G404.212.275.337.400.462.032-.062.063-.125.126-.187.188-.250.251-.312A406 B406 D406 F406 G406 .535 .313-.375A408 B408 D408 F408 G408 .670 .376-.500A502A503A504A506B502B503B504B506D502D503D504D506F502F503F504F506G502G503G504G506.300.362.425.550.063-.125.126-.187.188-.250.251-.375A50

12、8 B508 D508 F508 G508 .695 .376-.500A602A604A606B602B604B606D602D604D606F602F604F606G602G604G606.325.450.575.063-.125.188-.250.251-.375A608A610B608B610D608D610F608F610G608G610.700.850.376-.500.501-.625A612 B612 D612 F612 G612 .980 .626-.750A616 B616 1.240 .876-1.000A804A806A808B804B806B808D804D806D8

13、08F804F806F808G804G806G808.500.625.750.126-.250.251-.375.376-.500A810 B810 F810 G810 .900 .501-.625A812 B812 D812 F812 G812 1.03 .626-.750D816 1.290 .751-1.0002.2 Materials shall be of the type and grade specified in Table I.2.3 Surface Finish2.3.1 Aluminum alloy rivets shall be furnished either che

14、mically treated in accordance with MIL-C-5541, oranodically treated in accordance with MIL-A-8625 at the suppliers option2.3.2 Carbon steel bodies shall be zinc plated in accordance with ASTM B633, Type II, FE/ZN5 or phosphatecoated in accordance with Type Z, Class 2 or 4B of DOD-P-16232. Carbon ste

15、el mandrels shall be zinc platedor phosphate coated.2.3.3 Corrosion resistant steel bodies shall be passivated in accordance with ASTM A967. Corrosion resistantmandrels shall be passivated.2.4 Workmanship. Rivets shall be of uniform quality and free from injurious seams and other injurious defects.2

16、.5 Single shear load. The shear test shall be performed in accordance with Test Method 20 of NASM1312, orequivalent and shall conform to the data specified in Table I.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5942542.6 Tension load. The ten

17、sion test shall be performed in accordance with Test Method 8 of NASM1312, orequivalent and shall conform to the data specified in Table I.2.7 Packaging requirements The requirements for packaging shall be in accordance with ASTM D3951.3. QUALITY ASSURANCE PROVISIONS.3.1 Product conformance. The pro

18、ducts provided shall meet the salient characteristics of this commercial itemdescription, conform to the producers own drawings, specifications, standards, and the quality assurance practices,and be the same product offered for sale in the commercial market. The government reserves the right to requ

19、ireproof of such conformance.4. NOTES4.1 All dimensions are in inches.4.2 The part number shall consist of the basic Commercial Item Description Number followed by a dash numberfrom Table III. The dash number consists of a material combination symbol from Table I, a nominal bodydiameter size code in

20、 thirty-seconds of an inch from Table II, and a maximum grip code in sixteenths of aninch taken from Table III.EXAMPLE: AA59425 B 4 02Grip Range CodeNominal DiameterMaterialCommercial Item Description NumberAA59425B402 Indicates - Rivet, blind, nonstructural, retainedmandrel, open-end, domed head, 5

21、052(UNS A95052) aluminum body, 2024(UNS A92024) aluminum mandrel; nominalbody diameter size, .125; grip range, .063-.125.Military Interests:Custodians: Preparing Activity:Army - AR DLA-ISNavy - ASAir Force - 99Review Activities: (Project No. 5320-0954)Army - AV, MIAir Force - 11, 82National Security

22、 Agency-NSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3 and 8. In block 1, both the document number and revision letter should be given.

23、2. The submitter of this form must complete blocks 4, 5, 6 and 7.3. The preparing activity must provide a reply within 30 days from receipt of the form.NOTE: This form may not be used to request copies of documents, or to request waivers, or clarification of requirements on current contracts.Comment

24、s submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual.I RECOMMEND A CHANGE: 1. DOCUMENT NUMBERA-A-594252. DOCUMENT DATE (YYMMDD)9904203. DOCUMENT TITLE:RIVETS, BLIND, NONSTRUCTURAL, RETAINED MANDREL, OPEN END, DOM

25、ED HEAD, ALUMINUM ALLOY,CARBON STEEL, CORROSION RESISTANT STEEL4. NATURE OF CHANGE5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(2) AUTOVON (If applicable)7. DATE SUBMITTED (YYM

26、MDD)8. PREPARING ACTIVITY DLA-ISa. NAMEEmelia Altomarib. TELEPHONE (Include Area Code)(1) Commercial (215) 697-6827(2) (DSN) 442-6827c. ADDRESS (Include Zip Code)Defense Industrial Supply Center700 Robbins AvenueBldg. 3 (Code DISC-AESD)Philadelphia, PA 19111-5096IF YOU DO NOT RECEIVE A REPLY WITHIN

27、45 DAYS, CONTACT:Defense Quality and Standardization Office5203 Leesburg Pike, Suite 1403Falls Church, VA 22041TELEPHONE (703) 756-2340 AUTOVON 289-2340DD Form 1426, OCT 89 Previous editions are obsolete. 198/290Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-