DLA A-A-59352 A-2011 BATTERY DRY BA-223 U.pdf
《DLA A-A-59352 A-2011 BATTERY DRY BA-223 U.pdf》由会员分享,可在线阅读,更多相关《DLA A-A-59352 A-2011 BATTERY DRY BA-223 U.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, Columbus, ATTN: VAT, P.O. Box 3990, Columbus, OH 43218-3990, or email mailto:CircuitProtectdscc.dla.mil. Since contact information c
2、an change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 6135 INCH-POUND A-A-59352A 15 October 2011 SUPERSEDING A-A-59352 12 October 2000 COMMERCIAL ITEM DESCRIPTION BATTERY, DRY, BA-223/U The General Servic
3、es Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general requirements for a +22.5/45 V dc dry-cell battery. The battery is intended for use in portable electronic and communication equip
4、ment, flashlights, test equipment, and radio sets powered by non-rechargeable dry cell batteries. 2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This CID uses a classification system that is included in the PIN. The PIN shall be AA59352 (see 7.1). 3. SALIENT CHARACTERISTICS. 3.1 Interface an
5、d physical dimensions. Batteries supplied to this CID shall be as specified herein and shall meet the requirements of NEMA C18.1M Part 1 (see figure 1). 3.2 Voltage rating. The battery shall provide two nominal voltages: +22.5 V dc and +45 V dc. 3.3 Weight. The battery weight shall not exceed 3 poun
6、ds, 4 ounces. 3.4 Cell type. Cells shall meet the requirements of ANSI Number 1191SO of NEMA C18.1M, Part 1. 3.5 Dimensions. The batter shall meet the dimensional requirements shown in figure 1. 3.6 Marking. Batteries supplied to this CID shall be marked with the manufacturers (MFRs) standard commer
7、cial PIN. (NOTE: The part number marked on the unit pack shall be the CID PIN.) 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the
8、 operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.8 Workmanship. Batteries shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance.Provided by IHSNot
9、for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59352A 2 FIGURE 1. Configuration and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59352A 3 NOTES: 1. Dimensions are in inches. 2. Unless otherwise s
10、pecified, tolerance is .063 inch (1.59 mm). FIGURE 1. Configuration and dimensions. Ltr Inches mm Min Max Min Max A .438 - 11.11 - B 5.250 5.375 133.35 136.54 C 1.968 2.094 50.00 53.19 D 4.000 4.126 101.60 104.80 E 1.218 1.344 30.94 34.14 F 2.500 2.626 63.50 66.69 G 1.000 1.126 25.39 28.59 H .473 .5
11、98 12.01 15.19 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59352A 4 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with 23.403 of the Federal Acquis
12、ition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in
13、 the commercial market. The Government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. S
14、ee section 2 for PIN. 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAAA59352A2011BATTERYDRYBA223UPDF
