DLA A-A-59306 B-2012 FUSE CARTRIDGE CLASS T GENERAL REQUIREMENTS FOR.pdf

《DLA A-A-59306 B-2012 FUSE CARTRIDGE CLASS T GENERAL REQUIREMENTS FOR.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59306 B-2012 FUSE CARTRIDGE CLASS T GENERAL REQUIREMENTS FOR.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 INCH-POUND A-A-59306B 26 April 2012 SUPERSEDING A-A-59306A 19 December 2007 COMMERCIAL ITEM DESCRIPTION FUSE CARTRIDGE, CLASS T, GENERAL REQUIREMENTS FOR The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOP

2、E. This CID covers the general requirements for class T fuse cartridges. Requirements for specific fuse cartridges are covered in the individual CID specification sheets. Fuse cartridges covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION/PART OR IDENTIFICATION

3、 NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see 7.1). A-A-59306 /01 - 001 CID number Applicable CID specification Sheet (two digit) Dash number (see applicable CID specification sheet) 3. SALIENT CHARACTERISTICS. 3.1 Interface

4、and physical dimensions. Fuse cartridges supplied to this CID shall be as specified on the applicable CID specification sheet. 3.2 CID specification sheet. The family of fuse cartridges shall be in accordance with the requirements specified herein and the applicable CID specification sheet. In the e

5、vent of a conflict between this general CID and the applicable CID specification sheet, the latter shall govern. 3.3 Marking. Fuse cartridges supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN and the UL 248-15 listing mark. (NOTE: The part number marked on th

6、e unit pack shall be the CID PIN.) Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data that may improve this document should be sent to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, or email mailto:CircuitProtectdscc.dla.

7、mil. Since contact information can change you may want to verify the currency of the address information using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59306B 2 3.4 Recycled, recove

8、red, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.

9、3.5 Workmanship. Fuse cartridges shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum exten

10、t practicable, in accordance with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality as

11、surance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality of the product to be provided under this

12、 CID: a. The company producing the item must have been producing a product meeting the requirements of this CID for at least 6 months. b. The company producing the item must have sold 1,000 units meeting this CID in the commercial marketplace over the past 6 months. 6. PACKAGING. Preservation, packi

13、ng, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format example. 7.2 Environmentally preferable materials. Environmentally preferable materials should be use

14、d to the maximum extent possible to meet the requirements of this specification. As of the dating of this document, the U.S. Environmental Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website htt

15、p:/www.epa.gov/osw/hazard/wastemin/priority.htm. Included in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (C

16、AGE) code. For ordering purposes, inventory control, and submission of these fuse cartridges to DLA Land and Maritime under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Source of documents. FEDERAL REGULATIONS FAR - Federal Acquisition Reg

17、ulations (FAR). (Copies of this document are available online at https:/www.acquisition.gov/comp/far/index.html or from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401-0001.) 7.5 Ordering data. The contract or order should specify the following: a. CID docume

18、nt number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59306B 3 Other publications. Non Government Publications UNDERWRITERS LABORATORIES, INCORPORATED (UL)

19、UL 248-15 - Low-Voltage Fuses - Part 15: Class T Fuses. (Copies of this document are available online at http:/ or from the Underwriters Laboratories, Incorporated, 333 Pfingsten Road, Northbrook, IL 60062-2096.) (Industry association specifications and standards are generally available for referenc

20、e from libraries. They are also distributed among technical groups and using Federal agencies.) 7.5 Ordering data. The contract or order should specify the following: a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Government users. To

21、 acquire information on obtaining these fuse cartridges from the Government inventory system, contact DLA Land and Maritime, ATTN: DLA Land and Maritime-FMX, P.O. Box 3990, Columbus, OH 43218-3990, or telephone (614) 692-3677. 7.7 Changes from previous issue. Marginal notations are not used in this

22、revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC Project 5920-2012-016 NOTE: The activities listed above were interested

23、 in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-