DLA A-A-59305-1999 TERMINAL STUD THREADED DOUBLE TURRET《双转动架双头螺栓接线端头》.pdf

《DLA A-A-59305-1999 TERMINAL STUD THREADED DOUBLE TURRET《双转动架双头螺栓接线端头》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59305-1999 TERMINAL STUD THREADED DOUBLE TURRET《双转动架双头螺栓接线端头》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDA-A-5930515 April 1999SUPERSEDINGMS17172B (AS)12 October 1972COMMERCIAL ITEM DESCRIPTIONTERMINAL, STUDTHREADED DOUBLE TURRETThe General Services Administration has authorized the use of this commercial item description,for all federal agencies.1. SCOPE. This commercial item description cov

2、ers a double turret, threaded terminal stud foruse on terminal boards.2. SALIENT CHARACTERISTICS2.1 General . The terminal stud shall be a double turret threaded type.2.2 Material . The material shall be brass conforming to alloy C36000 of ASTM Standard B16,alloy C34200 or C35300 of ASTM Standard B1

3、21 or alloy C31400 of ASTM Standard B140.All alloys shall have a half-hard temper.2.3 Interface . Dimensional requirements are contained in table I and figure 1. Dimensions are ininches, unless otherwise specified and should be interpreted in accordance with ASME StandardY14.5M.2.3.1 Threads . The s

4、tud shall be threaded in accordance with ASME Standard B1.1, unified inchscrew thread UNC-2A no. 4-40.2.4 Workmanship . All surfaces shall be smooth and free of burrs and sharp edges.2.5 Finish . The finish shall consist of a tin plate, Type I, (0.0003 min.) per ASTM Standard B545or Type II (0.0001

5、min) per ASTM Standard B339 or equivalent.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any datawhich may improve this document should be sent to: Defense Supply Center Richmond(DSCR), 8000 Jefferson Davis Highway, Richmond VA 23297-5610.AMSC N/A FSC 5940DISTRI

6、BUTION STATEMENT A . Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593052TABLE I. Dimensional requirements .DashNumberThicknessofMountingBoardL.005Style-05 1-061/16 1/82-07 1-085/32 3/162-0

7、9 1-107/32 1/42-11 9/32 3/8 2FIGURE 1. Terminal stud .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5930533. REGULATORY REQUIREMENTSThere are no regulatory requirements, however, the offeror or contractor is encouraged to userecovered materials

8、 to the maximum extent practicable, in accordance with paragraph 23.403 ofthe Federal Acquisition Regulation (FAR).4. QUALITY ASSURANCE PROVISIONS4.1 Product conformance . The products provided shall meet the salient characteristics of thiscommercial item description, conform to the producers own dr

9、awings, specifications,standards, and quality assurance practices, and be the same product offered for sale in thecommercial market. The government reserves the right to require proof of such conformance.4.2 Market acceptability . Similar items must have been sold in the commercial market or to theG

10、overnment. The offeror or contractor shall certify and provide supporting documentation asto the serviceability and the long-term (5 years) availability of all necessary maintenance andlogistics support parts and materials.5. PACKAGINGPreservation, packing, and marking shall be as specified in the c

11、ontract or order.6. NOTES6.1 Source of documents .6.1.1 Source of government documents . Military and Federal documents are available from:Standardization Documents Order DeskBldg. 4D700 Robbins AvenuePhiladelphia, PA 19111-50946.1.2 Source of non-government documents . Applicable documents are avai

12、lable from thefollowing:American Society for Testing and Materials1916 Race StreetPhiladelphia, PA 19103-1187American Society of Mechanical Engineers345 East 47 th StreetNew York, NY 10017Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593054Custodian: Preparing Activity:Navy - AS DLA - GS(Pr oject 5940-1359)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-