DLA A-A-59303 A-2010 TALC TECHNICAL.pdf

《DLA A-A-59303 A-2010 TALC TECHNICAL.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59303 A-2010 TALC TECHNICAL.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information

2、can change, you may want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil. AMSC N/A FSC 6810 METRIC A-A-59303A SUPERSEDING 7 JUNE 2010 A-A-59303 16 October 1998 COMMERCIAL ITEM DESCRIPTION TALC, TECHNICAL The General Services Administration h

3、as authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers three types of modified commercial grade talc. Types T1 and T3 are intended for use as stimulants for riot control agents CA (orthochlorobenzylidene malononitri

4、le), CS1 and CS2. Type T1 is also intended for use in dusting and lubrication. Type T4, used for repairing and retreading pneumatic tires on ground vehicles, is equivalent to A-A-52518 Type IV Class B. 2. CLASSIFICATION. The talc shall be of the following types as specified (see 7.3) Type T1 - 35/65

5、 silicon dioxide Type T3 - 55/65 silicon dioxide Type T4 - 53 micrometer (m) 3. SALIENT CHARACTERISTICS 3.1 Chemical and physical characteristics. Talc shall conform to the chemical and physical characteristics of Table I when tested as specified herein. Provided by IHSNot for ResaleNo reproduction

6、or networking permitted without license from IHS-,-,-A-A-59303A 2 TABLE I. Chemical and physical characteristics. Characteristics Type T1 Type T3 Type T4 Test paragraph Min. Max. Min. Max. Max. Silicon dioxide, percent by weight 35 65 55 65 - 3.2 Calcium oxide, percent by weight - - - 0.30 - 3.2 Mag

7、nesium oxide, percent by weight 20 40 25 35 - 3.2 Loss on ignition, percent by weight - - - 8 - ASTM D1208 Loss on Ignition and Ash Asbestos and other fibers - None detected - None detected None detected 3.3 Percent by weight retained on a sieve - 5 - - 10 3.4 Average particle size, micrometers - -

8、- 3.5 - 3.5 Apparent density, grams per cubic centimeter - - - 0.25 - ASTM D1895 Method A Abbreviations: Min. = minimum; Max. = maximum; ASTM American Society for Testing and Materials 3.2 Oxide tests x-ray fluorescence (XRF) spectrometer method. 3.2.1 Instrument calibration. Certified magnesium oxi

9、de reference materials, plus other certified reference materials, shall be used in instrument calibration. The method by which the reference materials are prepared for instrument calibration must be identical to that for all samples. 3.2.2 X-ray emission spectrometric analysis. The x-ray emission sp

10、ectrometric analysis of magnesium oxide shall be performed by the same conditions and parameters established at the time of instrument calibration 3.2.3 Ignition. Samples shall be ignited to the oxide basis. Samples are then fused with lithium tetraborate, cast to form a fused glass disk, tempered a

11、nd readied for x-ray analysis. 3.2.4 Magnesium oxide content. Determine magnesium oxide content of each sample. The spectrometer shall produce a report that shows the silicon dioxide, calcium oxide, and magnesium oxide content. Provided by IHSNot for ResaleNo reproduction or networking permitted wit

12、hout license from IHS-,-,-A-A-59303A 3 3.2.5 Oxide tests alternate method. Determine the silicon dioxide, calcium oxide, and magnesium oxide content weight of the sample in accordance with ASTM D717, Analysis of Magnesium Silicate Pigment. 3.3 Asbestos and other fibers. Talc, technical, shall be fib

13、er free. For purposes of this test, a fiber is a particle that has a length greater than 5 micrometers and an aspect ratio (length to width ratio) of 3 or more to 1. Determine the presence of fibers in accordance with Environmental Protection Agency test method EPA/600/R-93/116, Method for the Deter

14、mination of Asbestos in Bulk Building Materials. 3.4 Percent retained on sieve. 3.4.1 Percent retained on sieve, Type T1. Determine the percent by weight of specimen retained on a No. 400 (38 m) sieve in accordance with ASTM D185, Standard Test Method for Coarse Particles in Pigments. 3.4.2 Percent

15、retained on sieve, Type T4. Determine the percent by weight of specimen retained on a No. 270 (53m) sieve in accordance with ASTM D185, Standard Test Method for Coarse Particles in Pigments. 3.5 Average particle size. Determine the average particle size of the specimen by a particle size analyzer us

16、ing the laser diffraction principle. 3.5.1 Average particle size alternate method. Determine the average particle size of the specimen in accordance with ASTM B330, Standard Test Method for Fisher Number of Metal Powders and Related Compounds. 4. REGULATORY REQUIREMENTS 4.1 Marking, packaging, and l

17、abeling. Material shall be labeled, packed, and marked in accordance with Title 49, Code of Federal Regulations (CFR) paragraphs 100 to 185. 4.2 Recycled materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practical, in accordance with paragraph 23.403 of

18、 the Federal Acquisition Regulation (FAR). 4.3 Material safety data sheet (MSDS). The manufacturer shall comply with requirements set forth by the Hazardous Communication Standard 29 CFR paragraph 1910.1200 (d) through (g). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products prov

19、ided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require pro

20、of of such conformance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59303A 4 5.2 Market acceptability. The following market acceptability criteria are necessary to document the quality of the product to be provided under this CID: a. The item

21、 offered must have been sold to the government within the past 2 years. b. The company must be able to show test data or lab results of meeting the salient characteristics of the talc. 6. PACKAGING. Additional preservation, packing, and marking shall be as specified in the contract or order. 6.1 Pac

22、kaging requirement. Type T3 packaging in 3.6 kilogram screw-cap plastic bottles shall conform to the Purchase Description EDAR Publication 196-21-87. 7. NOTES. This section contains information of a general or explanatory nature which is helpful, but is not mandatory. 7.1 Part or identification numb

23、er (PIN). The following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. 7.2 Sources of documents. 7.2.1 CFR and FAR. Copies of CFR and FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, P

24、A 15250-7954. Electronic copies of CFR documents may be obtained from http:/www.gpoaccess.gov/cfr/. Electronic copies of FAR documents may be obtained from http:/www.arnet.gov/far/. 7.2.2 ASTM standards. Copies of ASTM standards may be obtained from the ASTM International, 100 Barr Harbor Drive, P.O

25、. Box C700, West Conshohocken, PA 19428-2959. Electronic copies of ASTM standards may be obtained from http:/www.astm.org/. 7.2.3 Environmental Protection Agency (EPA) methods. EPA methods are available from Environmental Protection Agency, Ariel Rios Building, 1200 Pennsylvania Ave, Washington, DC

26、20460. Electronic copies of EPA documents may be obtained from http:/www.epa.gov. Type designation: A = Type T1 B = Type T3 C = Type T4 AA 59303 A Commercial item description number Example of PIN: AA59303A Prefix for commercial item description number Provided by IHSNot for ResaleNo reproduction or

27、 networking permitted without license from IHS-,-,-A-A-59303A 5 7.2.4 EDAR publication. Purchase Description EDAR Publication 196-21-87 is available from U.S. Army Edgewood Chemical Biological Center, Attn: RDCB-DEA-S, E3331, 5183 Blackhawk Road, Aberdeen Proving Ground, MD 21010-5424 or by e-mail a

28、t apgr-ecbcSpecsTeamconus.army.mil. 7.3 Ordering data. Acquisition documents must specify the following: a. Title, number, and date of this commercial item description. b. Type of talc required (see 2). c. Unit of issue and quantity. 7.4 National stock numbers (NSNs). The following NSNs correspond t

29、o this CID. They may not be indicative of all possible NSNs for this document. TABLE II. NSNs and type. NSN Type 6810-00-270-9988 T4 6810-00-270-9989 T4 6810-00-270-9990 T4 6810-00-543-7612 T1 6810-01-809-9589 T1 6810-00-142-9849 T3 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians:

30、 Air Force 68 Army EA GSA - FAS Review Activity: Army MD1 Preparing Activity: DLA - GS3 (Project 6810-2010-005) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-