DLA A-A-59163 A-2010 INSULATION TAPE ELECTRICAL SELF-ADHERING UNSUPPORTED SILICONE RUBBER.pdf

《DLA A-A-59163 A-2010 INSULATION TAPE ELECTRICAL SELF-ADHERING UNSUPPORTED SILICONE RUBBER.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59163 A-2010 INSULATION TAPE ELECTRICAL SELF-ADHERING UNSUPPORTED SILICONE RUBBER.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Logistics Agency Aviation VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. Since contact information can change, you m

2、ay want to verify the currency of this address information using the ASSIST database at https:/assist.daps.dla.mil/. FSC 5970 INCH-POUND A-A-59163A 5 November 2010 SUPERSEDING A-A-59163 13 February 1998 COMMERCIAL ITEM DESCRIPTION INSULATION TAPE, ELECTRICAL, SELF-ADHERING UNSUPPORTED SILICONE RUBBE

3、R The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers unsupported silicone rubber insulation tape which will adhere to itself at room temperature. The insulation tape is suita

4、ble for use at temperatures from -90 C to 260 C. 2. CLASSIFICATION. The insulation tape shall be classified by the following classes and types, as specified (see 7.3(b): Class 1 - Tapes conforming to inch-pound dimensions Type I - Rectangular cross-section Type II - Triangular cross-section with col

5、ored guidelines Class 2 - Tapes conforming to metric dimensions Type IM - Rectangular cross-section Type IIM - Triangular cross-section with colored guidelines 3. SALIENT CHARACTERISTICS 3.1 First article. When specified (see 7.3(c), a sample shall be subjected to first article inspection (see 7.5)

6、in accordance with 5.3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59163A 2 3.2 Material. The insulation tape shall be made of a self-adjusting silicone rubber material which will cure into a homogeneous mass. When wrapped or plied on itself

7、, it will cure to a homogeneous mass at room temperature (21 C to 27 C) in 48 hours or in 4 hours at 177 C. 3.3 Performance and product characteristics. The unsupported silicone rubber material shall have the following performance and product characteristics: 3.3.1 Dimensions and colored guidelines.

8、 The insulation tape shall be furnished in the following thicknesses, widths, and colored guidelines as specified in tables I, II, III, and IV. TABLE I. Type I dimensions. Thickness 0.010, 0.020, 0.030 0.002 inch (in) Width 0.50, 0.75, 1.00, 1.25, 1.50 inch TABLE II. Type II dimensions and colored g

9、uidelines. Thickness1 2(inch) Width (inch) Colored guidelines 0.020 0.030 0.040 0.050 0.060 0.080 1.00 1.00 1.00 1.25 1.50 1.50 Blue White Green Yellow Blue White 1Thickness tolerance shall be 0.002 inch. 2Thickness edge shall be not less than 0.007 inch and not greater than 0.009 inch. TABLE III. T

10、ype IM dimensions. Thickness 0.250, 0.500, 0.750 0.050 millimeter (mm) Width 15.0, 20.0, 25.0, 30.0, 40.0 0.5 (mm) TABLE IV. Type IIM dimensions and colored guidelines. Thickness1 2(mm) Width3(mm) Colored guidelines 0.500 0.750 1.000 1.300 1.500 2.000 25.0 25.0 25.0 32.0 38.0 38.0 Blue White Green Y

11、ellow Blue White 1Thickness tolerance shall be 0.050 mm. 2Thickness edge shall be not less than 0.200 mm and not greater than 0.230 mm. 3Width tolerance shall be 0.5 mm. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59163A 3 3.3.2 Rolls. Unless

12、 otherwise specified (see 7.3(d), the insulation tape shall be supplied in rolls of specified thickness and width (see 3.3.1) and wrapped on a core with insulation tape interleaved with quick-release film. The quick-release film shall be of sufficient width to preclude insulation tape edges from fus

13、ing during packaging, packing, and storage. Unless otherwise specified (see 7.3(d), the insulation tape shall be supplied in rolls not less than 11 meters (12 yards) in length.3.4 Physical properties. The physical properties of the unsupported silicone rubber material shall be as specified in table

14、V. TABLE V. Physical properties. Property Value types I and II Value types IM and IIM Test method Tensile strength, pound force per square inch (lbf/in2) kilopascal (kPa) 700 minimum 4,800 minimum ASTM D3759/ D3759M Elongation, percent 300 minimum 300 minimum ASTM D3759/ D3759M Water absorption1, pe

15、rcent by weight 3 maximum 3 maximum FED-STD-601, method 6251 Volume resistivity, ohms/circular mil/foot nanoohm meter 1 x 10131.7 x 1013ASTM D1458 Bond strength, 1 inch width, pounds 25 mm width, kilogram-force (kgf) 2.0 minimum 0.9 minimum ASTM D2148 Dielectric strength, volts/mil2 tape thickness0.

16、010 in 0.250 mm 0.020 in 0.500 mm 0.030 in 0.750 mm 0.040 in 1.000 mm 0.050 in 1.300 mm 0.060 in 1.500 mm 0.080 in 2.000 mm 400 minimum 400 minimum 400 minimum 300 minimum 275 minimum 250 minimum 200 minimum 400 minimum 400 minimum 400 minimum 300 minimum 275 minimum 250 minimum 200 minimum ASTM D14

17、93ASTM D214841See 3.5 for preparation of test specimen. 2This requirement is expressed in volts per thousandths inch thickness for both metric and inch-pound products. 3For types I and IM. 4For types II and IIM. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

18、m IHS-,-,-A-A-59163A 4 3.5 Preparation of test specimen for water absorption test. For types II and IIM, three strips of insulation tape shall be lapped together as shown in figure 1 to provide material for a dumbbell shaped die cut test specimen with uniform thickness. FIGURE 1. Preparation of insu

19、lation tape specimen for water absorption test. 3.6 Storage life. Insulation tape stored in unopened containers at a temperature of not greater than 37.3 C shall be capable of meeting all of the requirements of this specification for a period of 12 months from date of manufacture. (For storage life

20、extension, see 7.4.) 3.7 Workmanship. The insulation tape shall be uniform in quality and shall be free from splits, cracks, foreign material, and other defects that would affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials. The offeror/contractor is encour

21、aged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the prod

22、ucers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 5.2 Market acceptability. The products offered must have been previously sol

23、d either to the government or on the commercial market. 5.3 First article. When specified (see 7.3(c), a sample shall be subjected to first article inspection in accordance with the tests specified in section 3. 6. PACKAGING 6.1 Preservation, packing, and marking. Preservation, packing, and marking

24、shall be as specified in the acquisition order (see 7.3(e). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59163A 5 7. NOTES 7.1 Part or identification number (PIN). The following PIN procedure is for government purposes and does not constitute

25、a requirement for the contractor. AA59163 - X XXX XXXX Thickness 0020 0.020 in 0030 0.030 in 0040 0.040 in 0050 0.050 in 0060 0.060 in 0080 0.080 in 0250 0.250 mm 0500 0.500 mm 0750 0.750 mm 1000 1.000 mm 1300 1.300 mm 1500 1.500 mm 2000 2.000 mm Type I Rectangular cross-section II Triangular cross-

26、section with colored guidelines IM Rectangular cross-section IIM Triangular cross-section with colored guidelines Class 1 Tape to inch-pound dimensions 2 Tape to metric dimensions CID number Examples of reference part numbers: inch-pound AA59163-1I0020 metric AA59163-2IIM0250 7.2 Sources of document

27、s. 7.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies may be obtained from https:/www.acquisition.gov/far/. 7.2.2 Federal standards. Copies of federal standards may be obtained from General Services Administration, F

28、ederal Supply Service, Specification Section, 470 East LEnfant Plaza SW, Suite 8100, Washington, DC 20407. Electronic copies may be obtained from https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59163A 6 7.2.3 ASTM sta

29、ndards. Copies of ASTM standards may be obtained from the ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. Electronic copies may be obtained from http:/www.astm.org/. 7.3 Ordering data. The acquisition order should specify the following information: a. CID

30、document number, revision, and CID PIN. b. Class and type (see 2.). c. First article (see 3.1 and 5.3). d. When width, length, or thickness is other than specified (see 3.3.2). e. Preservation, packing, and marking (see 6.1). 7.4 Storage life extension. Insulation tape that has exceeded storage life

31、 may be examined for compliance with table V. Acceptable test results shall validate storage life extension for an additional 6 months (see 3.6). 7.5 First article. When first article inspection is required, the contracting officer should provide specific guidance to offerors whether the item(s) sho

32、uld be a first article sample, a first production item, or a number of items. The contracting officer should include specific instructions in acquisition documents regarding arrangements for examinations, approval of first article test results, and disposition of first articles. Invitations for bid

33、should provide that the Government reserves the right to waive the requirement for samples for first article inspection to those bidders offering a product which has been previously acquired or tested by the Government, and that bidders offering such products, who wish to rely on such production or

34、test, must furnish evidence with the bid that prior government approval is presently appropriate for the pending contract. 7.6 Subject term (key word) listing. Bond Cure Dielectric Lapped Plied Polymer Roll Self-adjusting Wrapped Provided by IHSNot for ResaleNo reproduction or networking permitted w

35、ithout license from IHS-,-,-A-A-59163A 7 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:Custodians: GSA - FAS Army - MI Air Force - 85 DLA - GS Review Activity: Air Force - 99 Preparing Activity: DLA - GS4 (Project 5970-2010-017) NOTE: The activities listed above were interested in this docu

36、ment as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-