DLA A-A-58030-1994 BOTTLES SHIPPING STORAGE NON-HAZARDOUS《无危险船运贮藏瓶》.pdf

《DLA A-A-58030-1994 BOTTLES SHIPPING STORAGE NON-HAZARDOUS《无危险船运贮藏瓶》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-58030-1994 BOTTLES SHIPPING STORAGE NON-HAZARDOUS《无危险船运贮藏瓶》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-58030 9999974 OLb5L47 844 METRIC I A-A-5803 O 15 SeDtember 1994 TO SUPERSEDE MIL-B-26701E (In Part) 14 May 1982 BOTTLES, SHIPPING, STORAGE, NON-HAZARDOUS The General Services Administration has authorized the use of this commercial item description for shipments of non-Department of Transportati

2、on regulated liquids in a polymer bottle. 1. ABSTRACT This commercial item description applies to high and low density polyethylene (HDPE/LDPE), polypropylene (PP), or other polymers which meet the requirements outlined in this commercial item description. The intended liquid or solid contents must

3、be compatible with the bottles material. These bottles are not intended to be used for transport of Department of Transportation regulated materials. 2. CLASSIFICATION This description covers bottles to be as follows: Style A: Round Style B: Square Style C: Rectangle Style D: Oval Class 1: Narrow Mo

4、uth Class 2: Large Mouth Beneficial comments (recommendations, additions, deletions, clarifications, etc.) and any data which may improve this document should be sent to: Air Force Packaging Evaluation Activity, HQ AFMC/LGTP, 5215 Thurlow Street, Wright-Patterson AFB, OH 45433-5540. AMSC N/A FSC 812

5、5 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-58030 9999974 01ibSL48 780 W . A-A-58030 Color a: Amber Color b: Clear (including uncolored HDPE) 3.1 Bottles and

6、 caDs. 3.1.1 Materials. The bottles and caps shall be made from clean recycled or virgin polymer material. Recycled material shall be preferred, when all salient characteristics are satisfied. The bottles shall be inherently leakproof and of commercial quality. The bottles shall exhibit the mold sta

7、mped or engraved recycling code outlined in PBI-24. The bottles shall exhibit a molded or stamped manufacturers identification markings, either the entire name or an industry recognized code. The bottle and cap manufacturer or distributor shall notify the end user of all chemical families which crea

8、te compatibility problems with the material used. The liner, if used, must be made of an inert material. Bottles, caps and liners, if required, all shall meet the applicable requirements in CFR 21 Parts 1-1299, especially the Food, Drug and Cosmetic: Act and amendments, for carrying human consumable

9、 products. 3.1.2 Co nstruction. Bottles shall be one piece, seamless construction and leakproof. Pinch-off welds are not to be construed as seams. Bottles greater than 3.8 liters shall exhibit either a handle or hand grip as an integral part of the bottle. Bottle shall achieve leakproofness with the

10、 cap using hand tightening procedures only. 3.2 Liner. If a cap liner is required for leakproofness, the liner must be made of inert material. The manufacturer shall notify the buyer about any compound families which may create liner compatibility problems. This notification shall be received upon r

11、eceipt of the bottles by the buyer. 3.3 CaDacities. BottILes shall have the following nominal capacities: 0.5 liters (1 pint) 5 liters (1.3 gallons) 1 liters (1.08 quart) 8 liters (2.1 gallons) 2 liters (2 -1 quarts) 10 liters (2.6 gallons) 2.2 liters (2.3 quarts) 25 liters (6.6 gallons) 4 liters (1

12、.05 ga.Llons) 50 liters (13.2 gallons) 4.3 litres (1.125 gallons) 3.4 Threads. Threads on the neck of the bottle with the cap shall be of the buttress or semi-buttress type allowing at least one revolution before seating of the cap against the bottle. When the cap is ccmpletely screwed onto the bott

13、le, the rim of the bottle shall seat Eirmly against theinner bearing surface of the cap or against the liner to ensure sealing. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A -A-5 030 9999974 OLb5L49 617 W A-A-5803 O 3.5 WorkmanshiD. The bottles

14、 shall be smooth, and the surface shall be free from ridges and pinch-off flash, flow marks, or depressions on mold partition line crevices. The bottles shall be uniform in color, texture, finish, and physical properties. The bottles shall also be free from bubbles, pinholes, dirt, foreign matter, w

15、arpage, chipped edges, blisters, scratches, and other defects affecting their serviceability or appearance. 4. REGULATORY REQUIREMENTS In addition to the Food, Drug and Cosmetic Act and the code in CFR 21 listed above, the contractor/offeror is encouraged to use recovered materials in accordance wit

16、h Public Law 94-580 to the maximum extent possible. 5. QUALITY ASSURANCE PROVISIONS 5.1 Contractor Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this Commercial Item Description, and that the product con

17、forms to the producers own drawings, specifications, standards, and quality assurance practices. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 5.2 Market AcceDtabili

18、tv. A bidder, a manufacturer of the item, shall produce documentation proving they produced 10,000 units of the size and type ordered each of the past three years. manufacturing bidder shall prove that they sold 10,000 units from the specific manufacturer used to fill the order, each of the past thr

19、ee years. Documentation shall be presented that the ordered quantity shall be received by the buyer within ninety days. A non- 5.3 Testina and inssection reauirements. A minimum ten samples shall be taken at random from the lot and inspected, for the defects listed below, when the lot size is less t

20、han 1,000 units Above 1,000 units the samples taken at random shall be tested at 1% of lot size. If more than 1% of the test lot exhibit failures, the test shall be repeated using all new samples with no additional failures prior to acceptance of the lot. 5.3.1 Bottles and caps made from an unauthor

21、ized polymer material. 5.3.2 5.3.3 Incompatibility documentation not included. 5.3.4 Bottles do not have a manufacturers name or an industry recognized code identifying the manufacturer. 5.3.5 Bottle not one piece. 5.3.6 5.3.7 Bottle not leakproof by hand tightening. 5.3.8 Liner not included, if req

22、uired. Bottles not marked with the appropriate recycling code. Bottle over 3.8 liters with no handle or hand grips. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58030 W 9999974 036.5350 339 = A-A-5803 O 5.3.9 Liner not an integral unit. 5.3.

23、10 Liner not made from inert material. 5.3.11 Threads not the buttress or semi-buttress type. 5.3.12 Threads seal before one complete rotation. 5.3.13 Bottle with cap sealed not leak proof. 5.3.14 (see 3.5). Bottle not in accordance with the workmanship paragraph 6. PACKAGING Packaaina, Packina, a n

24、d Markinq. Packaging, packing and marking should be standard industry practice, ASTM D 3951, unless otherwise required in ordering information. The bottles received shall have their respective caps attached or equivalent number of caps and bottles in a shipment. The caps shall be protected from brea

25、kage, loss or deformation. However, the minimum box marking required shall include: the name of manufacturer or distributor, contract number, quantity, bottle size and bottle material. 7. NOTES 7.1 Acauisition reauirements. Acquisition documents must specify the following: A. Bottle characteristics

26、(Style, Class and Color). B. Quantity required. C. Contractor documentation required in paragraphs 5.1, 5.2 and 5.3, as required. D. Additional packaging, packing and marking requirements, if any. 7.2 Part Number. The following part identification numbering - procedure is for government purposes and

27、 does not constitute a requirement for the contractor. The part number shall be determined as follows: A - XXXX - SQ - L - c Color a - Amber c - Clear Class N - Narrow mouth L - Large mouth Style RO - Round SQ - Square RE - Rectangle OV- Oval CID Number Designates a CID 7.3 Amlicable Documents. 7.3.

28、1 Laws a nd reaulations. CFR Title 21, Parts 1-1299 Food and Drug Administration 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-58030 74 OLb515L 275 9 A-A-5803 O Food, Drug and Cosmetic Act of 1958 and amendments Public Law 94-580 Environment

29、 (Resource Conservation and Recovery Act) (The Code of Federal Regulations, Title 21 and Public Laws are available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.) 7.3.2 Industrv sDecifications. ASTM ASTM D 3951 Commercial Packaging, Standards for (Applic

30、ation for copies should be addressed to ASTM, 1916 Race Street, Philadelphia, PA 19103-1187) Societv of the Plastics Industrv PBI-24 Plastic Bottle Material Code System- Mold Modification Drawings (Application for copies should be addressed to the Plastic Bottle Institute Division, Society cf the Pl

31、astics Industry Inc., 1275 K Street NW, Suite 400, Washington, DC 20005) MILITARY CUSTODIANS: Army - GL Navy - SA Air Force - 69 CIVIL AGENCY COORDINATING ACTIVITY GSA - FSS REVIEW ACTIVITIES: PREPARING ACTIVITY: Army - MD, SM, AR Air Force - 69 Air Force - 99 Navy- AS, MC DLA - GS Pro ect 812 5 -03 80 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-