DLA A-A-55570 4-2012 FUSEHOLDER EXTRACTOR POST IN-LINE NON-CRIMP TYPE ACCOMMODATES MINIATURE AUTOMOTIVE BLADE TYPE INCLOSED LINK FUSES.pdf

《DLA A-A-55570 4-2012 FUSEHOLDER EXTRACTOR POST IN-LINE NON-CRIMP TYPE ACCOMMODATES MINIATURE AUTOMOTIVE BLADE TYPE INCLOSED LINK FUSES.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55570 4-2012 FUSEHOLDER EXTRACTOR POST IN-LINE NON-CRIMP TYPE ACCOMMODATES MINIATURE AUTOMOTIVE BLADE TYPE INCLOSED LINK FUSES.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 INCH-POUND A-A-55570/4 20 December 2012 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET FUSEHOLDER, EXTRACTOR POST, IN-LINE NON-CRIMP TYPE, ACCOMMODATES MINIATURE, AUTOMOTIVE BLADE TYPE, INCLOSED LINK FUSESThe General Services Administration has authorized the use of this commercia

2、l item description for all federal agencies. The complete requirements for procuring fuseholders described herein shall consist of this document and the issue in effect of A-A-55570. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a

3、 classification system that is included in the PIN. The PIN shall be AA55570/04-001 (see NOTES). SALIENT CHARACTERISTICS. Interface and physical dimensions. Fuseholders supplied to this CID specification sheet shall be as specified herein (see figure 1). Ampere rating. The ampere rating shall be 30

4、amperes. Voltage rating. The voltage rating shall be 600 V ac. Fuseholder body material. The fuseholder body material shall be black Nylon 66. Terminal plating. Terminals shall be tin plated brass. Use of pure tin plating is prohibited as a final finish and as an undercoat. Use of tin-lead (Sn-Pb) f

5、inishes are acceptable provided that the minimum lead content is 3 percent. Operating temperature. The operating temperature shall be -55C to +120C. Non-Crimping. This is a no crimp in-line fuseholder. TABLE I. Electrical characteristics. CID dash number AA55570/04- Ampere rating Terminals Fuse acco

6、mmodation 001 30 amperes maximum Terminals will accept #12 - 18 AWG standard wire. 1/ Accommodates CID AA55569/02-001 through AA55569/02-010 fuses 1/ Use appropriate wire size based on the fuse used. For example, use #16 AWG wire for 20 A fuse. Provided by IHSNot for ResaleNo reproduction or network

7、ing permitted without license from IHS-,-,-A-A-55570/4 2 Ltr Inches mm Min Max Min Max A 0.725 0.735 18.42 18.67 B 2.225 2.235 56.52 56.77 NOTES: 1. Dimensions are in inches. 2. Tolerance is .005 inch (0.13 mm), unless otherwise specified. FIGURE 1. Configuration and dimensions. Provided by IHSNot f

8、or ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55570/4 3 NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. COMMERCIAL IT

9、EM DESCRIPTIONS A-A-55569/2 - Fuse, Inclosed Link, Fast Acting, 2 Amperes (A) through 30 A, Miniature, Automotive Blade Type. (Copies of this document is available online at https:/assist.dla.mil/quicksearch/ or https:/assist.dla.mil or from DLA Document Services, Building 4/D, 700 Robbins Avenue, P

10、hiladelphia, PA 19111-5094). Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were kn

11、own to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE MFRs name and address 1SK21 Posi-Produ

12、cts, Incorporated P.O. Box 3042 St. Augustine, Florida 32085-3042 Phone number (800) 785-2330 E-mail: mailto: serviceposi- Uniform Resource Locator (URL): http:/www.posi- Part number (P/N) supersession data. This CID specification sheet part number supersedes the following MFRs P/N as shown. This in

13、formation is being provided to assist in reducing proliferation in the Government inventory system. TABLE III. P/N supersession data. CID dash number AA55570/04- (see table I) MFRs CAGE MFRs P/N 1/ 001 1SK21 618 1/ The manufacturers P/N shall not be used for acquisition to the requirements of this C

14、ID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. For actual part marking requirements, see the marking paragraph of A-A-55570. Provided by IHSNot for ResaleNo reproduct

15、ion or networking permitted without license from IHS-,-,-A-A-55570/4 4 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC Project 5920-2012-073 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-