DLA A-A-55563 14 B-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITHOUT FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES WITH CONTROLLED INSIDE BEND RADIUS.pdf

《DLA A-A-55563 14 B-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITHOUT FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES WITH CONTROLLED INSIDE BEND RADIUS.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55563 14 B-2012 HOLDER ELECTRICAL CARD METAL CARD GUIDE LOW PROFILE OPEN ENDED WITHOUT FLARED ENTRY WITH 2 OFFSET (SIDE) MOUNTING HOLES WITH CONTROLLED INSIDE BEND RADIUS.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、INCHPOUND AA55563/14B 22 June 2012 Superseding AA55563/14A 31 January 2002 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITHOUT FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES, WITH CONTROLLED INSIDE BEND RADIUS The General Ser

2、vices Administration has authorized the use of this commercial item description (CID) for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA55563. . CLASSIFICATION/PART OR IDENTIFI

3、CATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA55563 CID number /14 Applicable CID sheet * Material (See table I) * Card holder wid

4、th/board thickness * * Length (See table II) * Finish (See table III) Example: AA55563/14AC20D is the PIN for a beryllium copper (of temper TD01), 2.0 inches (50.8 mm) long, black ebonal finished, low profile card guide with flared entry. The card guide is designed to accommodate circuit card assemb

5、lies with printed board thicknesses of .0937 inch (2.29 mm) and has two offset mounting holes. SALIENT CHARACTERISTICS. Interface and physical dimensions. The card holders supplied to this CID specification sheet shall be as specified herein (see figure 1, table I and table II) and meet the general

6、requirements specified in CID AA55563. Material type. Materials types shall be defined in of AA55563. The applicable material type designators for this CID specification sheet are “A“ (beryllium copper 1/4 H, temper TD01), “B“ (beryllium copper 1/4 HT, temper TH01), or “D“ (stainless steel 1/4 H). M

7、aterial thickness. The material thickness shall be .005 .002 inch (0.13 0.05 mm). Card holder width/board thickness. The card holder width/board thickness shall be defined in table I herein and is shown in figure 1 as dimensions “D“ and “T“. The applicable card holder width/board thickness designato

8、rs for this CID specification sheet are A, B, or C, and shall be included in the PIN. Overall length. Overall length is shown in figure 1 as dimension “L“, and is displayed in table II herein. Applicable overall length designator 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70 or 75 shall be included in

9、the PIN. AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/14B 2 Finish. Finish types shall be defined in AA55563. Applicable finish materials designators “C“ (copper plate), “D“ (black ebonal), “E“ (gold plate), “F“ (nickel p

10、late), “H“ (silver plate) “J“ (zinc, yellow chromate), “K“ (no finish), or “R“ (zinc, clear chromate) are available for material type designators “A“ and “B“. Finish designator “G“ (passivate) is the only finish available for material type designator “D“ (stainless steel). The finish designator shal

11、l be included in the PIN. Inches mm Inches mm Inches mm Inches mm Inches mm .001 .003 .005 0.03 0.08 0.13 .010 .020 .067 0.25 0.51 1.72 .070 .078 .100 1.78 1.98 2.54 .120 .125 .148 3.05 3.18 3.76 .180 .250 .370 4.57 6.35 9.39 NOTES: 1. Dimensions are in inches. 2. Millimeter equivalents are given fo

12、r general information only. 3. Unless otherwise specified, tolerances are .02 inch (0.51 mm), for 2 places and .010 inch (0.25 mm), for 3 places. FIGURE 1. Card holder design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA55563/14B

13、 3 TABLE I. Card holder width/board thickness. PIN designator for card holder width / board thickness Fractional equivalent Card holder width 1/ 2/ Dimension “D“ max Board thickness 1/ 2/ 3/ Dimension “T“ ref Inches mm Inches mm A 1/32 .27 6.85 .0312 0.76 B 1/16 .27 6.85 .0625 1.52 C 3/32 .27 6.85 .

14、0937 2.29 1/ See dimensions “D“ and “T“ in view A A on figure 1. 2/ Do not use card holder width/board thickness, dimensions “D“ or “T“ for PIN construction. 3/ Dimension “T“ is given as reference. TABLE II. Length and hole spacing. 1/ PIN designator for overall length Dimension “L” .020 (0.51) Dime

15、nsion “M” .005 (0.13) Inches mm Inches mm 20 2.0 51 1.75 44.5 25 2.5 54 2.25 57.2 30 3.0 76 2.75 69.9 35 3.5 89 3.25 82.6 40 4.0 102 3.75 95.3 45 4.5 114 4.25 108.0 50 5.0 127 4.75 120.7 55 5.5 140 5.25 133.4 60 6.0 152 5.75 146.1 65 6.5 165 6.25 158.8 70 7.0 178 6.75 171.5 75 7.5 191 7.25 184.2 1/

16、Dimensions are in inches. Millimeters are given for information only. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description AA55563

17、 Holder, Electrical Card, Metal Card Guide, General Requirements For. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering

18、data. Ordering data shall be as specified in AA55563. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet Provided by IHSNot for ResaleNo

19、reproduction or networking permitted without license from IHS-,-,-AA55563/14B 4 preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of app

20、roved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 18915 Birtcher A Division of Pentair Technical Products 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Fr

21、ee: (800) 8547086 Facsimile: (858) 7402430 URL: Part number (P/N) supersession data. These CID specification sheet PINs supersede the following manufacturers P/Ns in table III as shown. The CID PINs listed in table III cover the different lengths available. This information is being provided to ass

22、ist in reducing proliferation in the Government inventory system. TABLE III. Commercial part number supersession data. CID PIN; AA55563/14#$ AA55563/14#$& 1/ Manufacturers 2/ Material type () Card holder width/board thickness Overall length designator ($) Finish (&) CAGE 18915 4/ B # 60 3/ 357BHT12F

23、 B # 65 3/ 357BHT13F B # 70 3/ 357BHT14F B # 75 3/ 357BHT15F D # 20 G 357CRT4 D # 25 G 357CRT5 D # 30 G 357CRT6 D # 35 G 357CRT7 D # 40 G 357CRT8 D # 45 G 357CRT9 D # 50 G 357CRT10 D # 55 G 357CRT11 D # 60 G 357CRT12 D # 65 G 357CRT13 D # 70 G 357CRT14 D # 75 G 357CRT15 1/ See Classification/Part or

24、 Identification Number paragraph herein for symbol representations. 2/ The manufacturers part number shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replac

25、ed by the CID PINs shown. For actual part marking requirements, see the marking paragraph of AA55563. 3/ Finish materials designator “H”, “K”, “C”, ”D” “E”, “F”, “R”, or “J” are available for this material type. 4/ Manufacturer CAGE 18915 superseded part number the series type is “35-7“, the letters

26、 “B“, “BH”, or “CR” denotes material type, the letter “T“ denotes card holder width/board thickness (see table I), the numbers “2“ through “15“ denotes card holder lengths, and the letter “F“ denotes finish material. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Navy EC

27、 Air Force 99 Preparing Activity: DLA CC DLA CC Project 5998201231 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-