DLA A-A-55504 2 C-2011 FUSEHOLDER EXTRACTOR POST FRONT MOUNT HIGH PROFILE FINGER GRIP KNOB FUSE CARRIER FOR 3AG ( 25 INCH (IN) X 1 25 IN (6 35 MILLIMETERS (MM) X 31 75 MM)) OR 196 .pdf

《DLA A-A-55504 2 C-2011 FUSEHOLDER EXTRACTOR POST FRONT MOUNT HIGH PROFILE FINGER GRIP KNOB FUSE CARRIER FOR 3AG ( 25 INCH (IN) X 1 25 IN (6 35 MILLIMETERS (MM) X 31 75 MM)) OR 196 .pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55504 2 C-2011 FUSEHOLDER EXTRACTOR POST FRONT MOUNT HIGH PROFILE FINGER GRIP KNOB FUSE CARRIER FOR 3AG ( 25 INCH (IN) X 1 25 IN (6 35 MILLIMETERS (MM) X 31 75 MM)) OR 196 .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5920 INCH-POUND A-A-55504/2C 9 May 2011 SUPERSEDING A-A-55504/2B 20 January 2006 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET FUSEHOLDER, EXTRACTOR POST, FRONT MOUNT, HIGH PROFILE, FINGER GRIP KNOB FUSE CARRIER FOR 3AG (.25 INCH (IN) X 1.25 IN (6.35 MILLIMETERS (MM) X 31.75 MM) OR .1

2、96 IN X .787 IN (5 MM X 20 MM) FUSE CARTRIDGES The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. The complete requirements for procuring the fuseholders described herein shall consist of this document and the issue in effec

3、t of CID A-A-55504. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES). AA55504/02- Accommodates fuse Rear terminal configuration 001A 3

4、AG A 001B 3AG B 001C 3AG C 001D 3AG D 002A 5 mm x 20 mm A 002B 5 mm x 20 mm B 002C 5 mm x 20 mm C 002D 5 mm x 20 mm D SALIENT CHARACTERISTICS. Interface and physical dimensions. Fuseholders supplied to this CID specification sheet shall be as specified herein (see figure 1). Rear terminal configurat

5、ion. The rear terminal configuration shall be as specified in A-A-55504. Mounting hole. The mounting hole shall be as specified in figure 1. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification information for P

6、IN format example. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55504/2C 2 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .005 inch (0.13 mm). FIGURE 1. Configuration and dimensions. Inches mm Inches mm .311 7.

7、90 .510 12.95 .457 11.60 .618 15.70 .465 11.81 .689 17.50 .469 11.90 .693 17.60 .480 12.19 .906 23.00 .500 12.70 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55504/2C 3 Commercial products. As part of the market analysis and research effort, t

8、his CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE

9、: This information should not be considered as a list of approved manufacturers or be used to restrict acquisition to only the manufacturers shown.) MFRs CAGE MFRs name and address 71400 Cooper Bussmann, Incorporated P. O. Box 14460 St. Louis, MO 63178-4460 Phone number (636) 394-2877 Facsimile numb

10、er (800) 544-2570 E-mail: mailto: Uniform Resource Locator (URL): https:/ Part number (P/N) supersession data. These CID specification sheet PINs supersede the following MFRs P/Ns as shown. This information is being provided to assist in reducing proliferation in the Government inventory system. TAB

11、LE I. P/N supersession data. CID dash number AA55504/02- (see table I) MFRs CAGE 71400 MFRs P/N 1/ 001A HTB-42I 001B HTB-44I 001C HTB-46I 001D HTB-48I 002A HTB-42M 002B HTB-44M 002C HTB-46M 002D HTB-48M 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specif

12、ication sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID P/N shown. For actual part marking requirements see the marking paragraph of A-A-55504. Provided by IHSNot for ResaleNo reproduction or net

13、working permitted without license from IHS-,-,-A-A-55504/2C 4 National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID specification sheet. The list is for information only and may not be indicative of all possible NSNs associated with the CID specification

14、sheet. For up to date information on assigned NSNs, please contact the aforementioned DLA Land and Maritime office (See A-A-55504). TABLE II. NSNs. Dash number (see table I) AA55504/02- NSN 001A N/A 001B 5920-00-858-8161 001C 5920-01-116-8359 001D N/A 002A N/A 002B 5920-01-349-0012 002C N/A 002D N/A

15、 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Navy - EC Preparing activity: DLA - CC DLA-CC P

16、roject 5920-2011-021 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-