DLA A-A-55238-1993 CASE FIELD FIRST AID DRESSING LEATHER (MILITARY POLICE)《宪兵穿急救行李箱》.pdf

《DLA A-A-55238-1993 CASE FIELD FIRST AID DRESSING LEATHER (MILITARY POLICE)《宪兵穿急救行李箱》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55238-1993 CASE FIELD FIRST AID DRESSING LEATHER (MILITARY POLICE)《宪兵穿急救行李箱》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55238 9999974 0155806 7TT I INCH-POUND I A-A-55 238 September 29, 1993 COMMERCIAL ITEM DESCRIPTION CASE, FIELD, FIRST AID DRESSING, LEATHER (MILITARY POLICE) The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-C-1002. Abstract. The

2、first aid field case is intended for use by members of the Military Police of the U. S. Army and Air Force. The case is a leather pocket enclosure with snap fastener. It is worn on a belt. The case is designed to hold a Dressing, First Aid, Individual Troop, Camouflage (First Aid Packet). Classifica

3、tion. The field case is provided in one type and size. Salient Characteristics. The Case, First Aid Dressing shall be of two piece leather pocket construction capable of belt attachment, and an overlapping flap. In a fully extended, open configuration, the case shall measure 6 1/4 inches high, by 5

4、- +1/16 inches long. The flap shall have a snap closure. The main body of the pocket shall form the back, being contiguous with the flap. The sewn-on pocket portion shall be molded to the back portion, creating a cavity for intended contents. Stitching around body shall be 3/16 inch from edge. The m

5、ain body, back portion, shall be perforated with two slots, 1/8 inch each, centered three inches apart, and 2 inches high. The case, including flap shall be shaped and dimensioned as indicated in Figure 1. 1 rn .I I j. Beneficial comments (recommendations, additions, deletions) and any pertinent dat

6、a which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at t

7、he end of this document or by letter. AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55238 m 7Y 0155807 636 m A-A-55 23 8 Stitched double edges o

8、f body and flap edge shall be sealed with a colorless aqueous solution similar to gum tragacanth and smoothly burnished. All stitching shall be lock-stitch, type 301, 4-6 stitches per inch. Ma ter i a 1 s Leather: The leather shall conform to any type of mildew resistant treated cattlehide leather c

9、onforming to the provisions of KK-L-271. The leather shall be dyed black and finished smoothly on the grain side with a long- lasting lustrous finish. The finished grain side shall be used for all visible facings. The body portion contiguous to the flap shall be 6/64 inches thick, and the remaining

10、front portion, 4/64 inches thick. Thread: The thread shall be twisted soft or bonded multiple cord, normal elongation, 3 ply general purpose polyester with a minimum breaking strength of 24 pounds. The color shall be black and exhibit colorfastness to weathering in compliance with conventional comme

11、rcial practice. Ends of stitching shall be backstitched or over-stitched not less than 1 inch, except where ends are turned under, or caught in other seams and stitching. Fastener, snap: Snap fasteners shall be steel, with black finish consisting of size 2 button with socket for the female half, and

12、 size 2 eyelet with stud for the male half. The button/socket assembly shall be conventional, commercial spring clamp type. Sizes and lenaths. The finished case shall conform to the dimensions indicated in the above description, and Figure 1. Label/markinq. The epithet “U.S.“ and contractor logo, or

13、 trademark, shall be permanently and legibly indented on the back of the case, in accordance with instructions provided in Figure 1. Label/Taq. Each item shall be individually bar-coded with the type VIII, class 17 label/tag of DDD-L-20. This label/tag shall be located so that it is completely visib

14、le on each item and cau,ses no damage to the item. Workmanship. After completion, the finished case shall be in compliance with configuration, construction, components, and finish as stated in this description. The case shall be complete and capable of holding the First Aid Packet. Snap fasteners sh

15、all be properly seated, and clinched assuring flawless opening and closing of case. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55238 = 9999974 0155808 572 : A-A-55 2 3 8 Thread tension shall be uniformly secure, with thread ends tied and f

16、used. The finished case shall be thoroughly cleaned with all loose thread, lint, and other debris removed. The case shall be free from irregularities or defects which adversely affect appearance, performance, reliability, or durability. Product Demonstration Model. When required, offerers shall subm

17、it samples of their intended production. The product demonstration model will consist of units independently developed. Product demonstration models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product demonstration mode

18、ls will be retained by the government. One (i) product demonstration model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the product demonstration model does not rel

19、ieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Requlatory Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Quality As

20、surance O Certification. The contractor shall certify that the product offered meets the salient characteristics of this description including Figure 1. The contractor may use his own drawings, specifications, standards and quality assurance practices to the extent they comply with this description.

21、 The government reserves the right to require proof of such conformance prior to the first delivery, and thereafter, as may be otherwise provided for, under the provisions of the contract. Reliance on contractor quality assurance systems shall not relieve the contractor of the responsibility of ensu

22、ring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Examination Visual Examination. The field cases shall be examined for the defects listed below. The lot size shall be expressed in units of field cases. The sample unit is one

23、field case. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55238 9999974 0255809 409 A-A- 5 5 2 3 8 Defects. The field cases shall be examined for the following defects: Body: any hole, cut, tear, color not as specified; any spot or stain (outsi

24、de); thread ends not removed; failure to clean, remove lint or other foreign matter, measurement of item not as specified. Any component, assembly, finish or workmanship feature not in compliance with applicable requirements of this Commercial Item Description Leather: evidence of loose flesh, slaug

25、hter cuts, abrasions or scratches, holes, hip marks, grub damage, brand marks, wrinkles, flanky, spongy, pipey or stretchy leather, not dyed and finished on grain side; not black in color; improper or incomplete burnishing of matched edges. Thread/Stitching: not type specified, skipped stitching, op

26、en seam; loose thread tension; failure to tie and fuse thread ends, stitches per inch not as specified. Hardware: Snap fastener not as specified or omitted; improperly mated, clinched or seated; any other malfunction adversely affecting ease of operation. Bar Code: Bar code omitted or not readable b

27、y scanner, Human-Readable Interpretation (HRI) omitted or illegible; bar-coded type not as specified, code density not as specified. Dimensional Examination. The finished field case shall conform to the dimensions specified in Figure 1. Any dimension that is not within the established tolerance shal

28、l be classified as a defect. The sample unit shall be one field case. Packaqinq Examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. EXAMINE DEFECT Marking Omitted

29、; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Ma teria 1 s Any component missing, damaged, or not as specified 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55238 9999974 0155810 120 A-A-

30、55238 O EXAMINE DEFECT Workmanship Con tent Palletization Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of items in container is more or less than required NSN shown on one or more items not as Sp

31、ecified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified Preservation, Packinq, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government Docu

32、ments. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Custodian: AITIY - GL Air Force - 99 Review Activity: Army - MD Air Force - 82, 45 Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8465-0150 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5523 9999974 Ol1558LL Ob7 m / I FIGURE 1 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-