DLA A-A-55232-1995 TROUSERS MAN-S HOSPITAL DUTY UNIFORM (HDU)《男子医院制服的宽松裤》.pdf

《DLA A-A-55232-1995 TROUSERS MAN-S HOSPITAL DUTY UNIFORM (HDU)《男子医院制服的宽松裤》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55232-1995 TROUSERS MAN-S HOSPITAL DUTY UNIFORM (HDU)《男子医院制服的宽松裤》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 A-A-55232 9999974 0169295 047 W A-A-55 2 3 2 October 10, 1995 COMMERCIAL ITEM DESCRIPTION TROUSERS, MANS: HOSPITAL DUTY UNIFORM (HDU) The General Services Administration has authorized the use of this commercial item description in preference to MIL-T-44291. 1. SCOPE. This commercial item descripti

2、on covers the requirements for mens trousers made of twill weave, polyester/cotton cloth. part of the hospital duty or food handlers uniform by male personnel of the Department of Defense. The trousers are intended to be worn as 2. SALIENT CHARACTERISTICS 2.1 Salient characteristics. The trousers sh

3、all be dress type with sewn on waistband, hook and eye or button/buttonhole front closure with slide fastener, lined left-over-right front fly (bartacked at base), two front pockets (side seam or quarter top), uncut back darts, and two double or single corded back pockets with button/buttonhole tab

4、on left pocket or both. seat seam shall be adjustable by means of a seam outlet. waistband shall be cut from basic material and shall be lined and interlined. There shall be seven (7) sewn belt loops for trousers sizes 30 through 36 and eight (8) for sizes 38 and up. All exposed raw edges shall be f

5、inished and the leg bottoms shall be hemmed. additional stitching. pointas of strain. The The All pressure points shall be reinforced with Bartacks shall be positioned to reinforce (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be

6、 addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FNSC, 2800 South 20th Street, Philadelphia, PA 19145-5099. AMSC N/A DISTRIBUTION STATEMENT A. FCC 8405 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction o

7、r networking permitted without license from IHS-,-,-A-A-55232 997777Li 0169276 T3 A-A-55 2 3 2 2.2 Fiqure. Figure 1 is furnished for information purposes only. If there are any inconsistencies between the written commercial item description and Figure 1, the written commercial item description shall

8、 govern. 2.3 Materials 2.3.1 Basic material. The basic material for the trousers shall be a 2/1 left hand twill for uniformity consisting of 65 (25) percent spun polyester and the remaining percentage combed cotton. The cloth shall be bleached optical white and shall conform to the requirements in T

9、able I. 2.3.2 Lininq. The material for the left fly interlining, right fly lining, waistband lining and pocketing shall be white, woven, 100 percent polyester, polyester and cotton, or polyester and rayon cloth. The finished cloth shall conform to the requirements in Table I. 2.3.2.1 Interlininq. Th

10、e material for interlining the waistband may be bleached or unbleached commercially accepted cotton buckram and shall conform to the requirements in Table I, or a na-tural color nonwoven interlining with a minimum weight of 3.0 oz./sq. yd. 2.3.3 Thread. The thread for seaming, stitching, buttonholes

11、 and button sewing shall be white, polyester core with cotton or polyester covering, with a minimum breaking strength of 3.0 lbs.* An alternate thread for seaming, stitching, buttonholes and button sewing shall be white, spun polyester thread with a minimum breaking strength of 2.2 lbs.*. * When tes

12、ted as specified in ASTM D-2256. 2.3.4 Gimp. The gimp for reinforcing buttonholes shall be 100 percent cotton, bleached white, with a minimum breaking strength of 6.5 lbs. when tested as specified in ASTM D-2256. 2.3.5 Buttons. The buttons shall be flat, 4-hole sewing style, 22-line, shade white to

13、approximate the basic material. 2.3.6 Hook and eye. The hook and eye waistband closure shall have a nickel plated finish and shall be suitable for mens trousers. 2.3.7, Slide fastener. The slide fastener for closing the front fly shall be non-separating, non-reversible, and have a polyester continuo

14、us monofilament or brass chain, with automatic, cam or ratcheting lock, short tab pull, and bottom stop. The tape and the monofilament chain with slider shall be white. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-55232 m 9999974 0169277 71

15、iT m A-A-55 2 3 2 TABLE I. - Material requirements Interlining 4.5 Test method ASTM- D3776 OPT. C Lining Characteristic Weight: (min.) oz./sq. yd. Basic material 6.8 - 3.6 AATCC 61 TM-3A AATCC 135 Breaking strength: (min.) pounds Warp Filling Shrinkage and elongation: (max. ) Warp Filling pH : (min.

16、 ) (max. ) 170 120 - 2.0 2.0 - - 5.0 8.5 - 75 55 Seam efficiency: Colorfastness: Laundering Minimum rating 80 percent l- Minimum rating 11 4 II Tearing strength: (min. ) Warp Filling 5.0 4.5 ASTM- D5034 - I ASTM- 1 D629 - I I I ASTM- D1424 =I Test 5110 1 L/ - i/ Tested in accordance with FED-STD-191

17、, TM-5110 except that the needle shall measure 0.36 (2 0.001) inch across the blade at the eye, and the thread shall be as specified in paragraph 2.3.3. 2.4 Label/taq. Each item shall be individually bar-coded with a paper tag for personal clothing items. shall be standard bleached sulfate having a

18、basis weight of 100 pounds. finish to accept thermal transfer and direct printing. shall have a hole and shall be attached to each item by a fastener, clearly legible and readable by a scanner. The bar coding element shall be a 13 digit national stock number (NSN). The bar code type shall be a mediu

19、m to high code density and shall be located so that it is completely visible on the item when it is folded and/or packaged as specified and so that it causes no damage to the item. The paper tag The paper used for the tags shall have a smooth The tags 3 Provided by IHSNot for ResaleNo reproduction o

20、r networking permitted without license from IHS-,-,- A-A-55232 9999974 0169296 5b A-A-5 5 2 3 2 2.4.1 Labels. A commercial-type label is acceptable, provided that an additional printed cloth label containing the contractors name, contract number, size and National Stock Number (NSN) is caught on the

21、 stitching of the commercial label. The commercial label shall include fiber and laundering information. , 2.5 Sizes and measurements. The finished trousers shall conform to the measurements in Table I. TABLE 1. Finished measurements in inches I Size 30 32 34 36 38 40 42 44 46 I 1/2 Waist i-/ 15 16

22、17 18 19 20 21 22 23 inseam 2/ X-Short 28 28 28 28 28 28 28 28 28 Short 30 30 30 30 30 30 30 30 30 Regular 32 32 32 32 32 32 32 32 32 X-Long 36 36 36 36 36 36 36 36 36 Long 34 34 34 34 34 34 34. 34 34 - i/ Measure along top edge of waistband from folded edge to folded edge with front closed. inch fo

23、r 1/2 waist measurement. The tolerance shall be - +1/4 - 2/ Measure along inseam from crotch seam to bottom edge of leg. The tolerance shall be t1/2 inch for inseam measurement. NOTE: The lengths (X-Short, Short, Regular, Long, and X-Long) may be abbreviated as XS, S, R, L and XL. 2.6 Patterns. The

24、Government shall furnish a single size The government patterns may be used to create the pattern. contractors working patterns. However, the design of the patterns shall not be altered in any way. Commercial patterns may be used in lieu of the government-furnished patterns. Minor modifications are p

25、ermitted to accommodate automation. However, the design and measurements of the government-furnished pattern must be maintained for both working and commercial patterns. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ A-A-5 5 23 2 3. REGULATORY R

26、EQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. QUALITY ASSURANCE PROVISIONS 4.1 Certification. The contractor shall certify and maintain substantiating

27、 evidence that the product offered meets the salient characteristics of this commercial item description; conforms to the producers own drawings, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to the first deli

28、very and thereafter as may be otherwise provided for under the provisions of the contract. 4.2 Market acceptance criteria. The item offered, or a generic equivalent, must have been sold to the commercial market or to the Government for at least 2 years. 4.2.1 Warrantv. The item offered shall include

29、 the standard warranty given to the commercial market beginning with the date of delivery of the individual items. the defects listed below in accordance with ANSI/ASQC 21.4. 4.3 Visual examination. Each trouser shall be examined for 4.3.1 Defects. Any hole, cut, or tear; color not as specified; any

30、 part shaded; any spot or stain (visible on outside of trousers); raw edges, open seams, thread ends not removed, or loose tension resulting in loose seams; any material defects, distorted parts or poor workmanship; any component part omitted or defective; label missing, incorrect, or illegible; mea

31、surement of item not as specified; bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code causes damage to the item; any items not packaged in accordance with the contract or purchase order; any r

32、equirement omitted or not as specified. specified in the contract or purchase order. 4.4 Acceptance criteria. Acceptance criteria shall be as 5. PACKAGING 5.1 Preservation, packinq, and markinq. The preservation, packing, and marking shall be as specified in the contract or purchase order. 5 Provide

33、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55 23 2 6. NOTES 6.1 Source of Government documents. Copies of military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-509

34、4 6.2 Source of non-Government documents ASTM Test Methods (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) AATCC Test Method (Applications for copies should be addressed to American Association of Textile Che

35、mists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215.) ANSI/ASQC Z1.4 - Sampling Procedures. and Tables for Inspection of Attributes (Applications for copies should be addressed to American National Standards Institute, 11 West 42nd Street, New York, NY 10036-8002.) Custodians:

36、Army - GL Air Force - 45 Review Activities: Army - MD Air Force - 32, 82 Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8405-0201 1 User Activities: Navy - NU Navy - MC Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55232 9999974 OLb9301 170 A-A-55232 - FIGURE 1. Trousers, Mans: HosDita Dutv Uniform (HDU) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-