DLA A-A-55123 A-1994 SMOCK GENERAL PURPOSE《工作服的一般用途》.pdf

《DLA A-A-55123 A-1994 SMOCK GENERAL PURPOSE《工作服的一般用途》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55123 A-1994 SMOCK GENERAL PURPOSE《工作服的一般用途》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-55123A E 9999974 01b.5549 240 m . A-A-55123A November 18, 1994 Superseding February 17, 1993 A-A-5 5 12 3 COMMERCIAL ITEM DESCRIPTION SMOCK, GENERAL PURPOSE The General Services Administration has authorized the use of this commercial item description in preference to MIL-S-2124. 1. SCOPE 1.1 Th

2、is commercial item description covers the requirements for smock, general purpose. The smock is intended for wear by personnel of the Department of Defense. 2. SALIENT CHRRACTERISTICS 2.1 Description. The smock shall be full fitting and knee length with long sleeves. The front closure shall be singl

3、e- breasted and button-down. The collar shall be a notched lapel collar. There shall be two lower patch pockets positioned at mid-thigh, two side hand openings at patch pocket location and a left side patch breast pocket with optional pencil section. The back shall be constructed to allow comfort in

4、 movement. All visible seams shall be clean finished. Stitch types and hems shall be uniform on all smocks. 2.2 Materials 2.2.1 Basic material. The basic material shall be white pre-shrunk cotton drill or a polyester/cotton twill blend having a minimum of 65% polyester and the remainder cotton, weig

5、hing a minimum of 6.0 oz./sq. yd. when tested in accordance with ASTM-D 3776, Option C. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Di

6、rectorate, Attn: DPSC-FQSD, 2800 South 20th Street, Philadelphia, PA 19145-0599. AMSC N/A DISTRIBUTION STATEMENT A. FSC 8415 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55L23A D 9999974

7、0365550 Tb2 W A-A-55123A The breaking strength shall be a minimum of 90 pounds (warp) and 55 pounds (filling) when tested in accordance with ASTM-D 5034. The maximum shrinkage, after preshrinking, shall be 2.0 in either the warp or filling direction when tested in accordance with AATCC-135. 2.2.2 Bu

8、ttons. The buttons shall be plastic, size 30-line, 4-hole, white or pearlescent white. They shall be sewn securely to right front to correspond with buttonholes. shall be a straight cut or whip type with purling on the outside of the smock. The buttonholes shall be cut so that they fit easily over t

9、he buttons. purpose intended, and the same as used in the smockthe contractor offers in the commercial marketplace. The buttonholes 2.2.3 Thread. The thread shall be white, suitable for the 2.2.4 Bartack or automatic line tack. The bartack or line tack shall measure 1/2 + 1/8 inch in length with at

10、least 28 stitches per bartack or line tack and shall be positioned as follows: Ends of pocket openings (vertical), across side seams at top and bottom of hand openings (horizontal). If back is designed with center back seam and vent, a bartack shall be across the end of center back seam at top of ve

11、nt (horizontal). 2.3 Label/markinq. Each smock shall have a commercial identification label and a size label or a combination identification/size label. The labels shall be bleached white. The printing shall be black and shall consist of suitable non- toxic dye(s) or pigment(s) in a medium which yie

12、lds a permanent impression. It shall not show off-setting, smearing, bleeding or discoloration. Identification label shall be centered and caught in the inside stitching of the hem of the right lower pocket. The contents of the identification labels shall be as follows: Identification Size label Ite

13、m description Size Contract number Stock number Fiber content Contractors name Applicable care instructions (As an alternate, the care instructions shall be located on the size label in lieu of the Identification label). Size or identification/size label shall be caught in stitching, inside, at cent

14、er of neck undercollar joining seam. 2.4 Label/taq. Each item shall be individually bar-coded with a paper tag for personal clothing items, standard bleached sulfate, with a basis weight of 100 pound. The paper used for the tags shall have a smooth finish to accept thermal transfer and direct printi

15、ng. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55123A S 9999974 0165551 9T9 A-A-55123A Bar coded tags shall have a hole and shall be attached to each smock by a fastener, clearly legible and readable by a scanner. The bar coding element sh

16、all be a 13 digit national stock number (NSN). The bar code type shall be a medium to high code density and shall be human-readable interpretation (HRI). This label/tag shall be located so that it is completely visible on the item when it is folded and/or packaged as specified and so that it causes

17、no damage to the item. conform to the measurements below. 2.5. Sizes and measurements. The finished smocks shall Table I. Finished measurements inches) Sizes Small Medium Large X-Large Tol. 1/2 Chest I/ 22 24 26 28 - + 3/4 Sleeve length 2/ All sleeve lengths shall be 18-1/2 inches Back length 3/ All

18、 back lengths shall be 41-43 inches Lower pockets: All lower pockets shall be 7 (+ 1/4) inches (minimum) Width (inches) wide and 7 (2 1/4) inches deep. Top pockets: Depth (inches) All top pockets shall be 5-1/2 (2 1/4) inches wide and 6 (+ 1/4) inches deep. I/ With the smock buttoned, measure across

19、 chest, at base of armhole, from folded edge to folded edge. 2/ Measure sleeve seam from underarm and armhole joining seam to bottom of sleeve. a/ Measure back length down center of back from collar joining seam to a point in line with bottom of smock. NOTE: Hand openings shall not be less than 6 in

20、ches long and shall not vary in length more than 1/2-inch. 3. REGULATORY REQUIREMENT. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without

21、 license from IHS-,-,-A-A-55123A m 9999974 0365552 835 m A-A-55123A 4. QUALITY ASSRANCE PROVISIONS 4.1 Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description; conforms to the prod

22、ucers own drawings, specifications, standards, and quality assurance practices; and otherwise is the same product offered for sale in the commercial marketplace. Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided

23、 for under the provisions of the contract. The 4.2 Market acceptability criteria. The item offered must have been sold to the commercial market for at least two years or to the Government, and the contractor shall certify and provide supporting documentation as to its successful serviceability. 4.3

24、Warranty. The item offered shall include the standard warranty given to the commercial market beginning with the date of delivery of the individual items. 4.4 Visual examination. Each smock shall be examined for the defects listed below: Any hole, cut, tear, burn, poorly pressed, mend, basting not r

25、emoved; color not as specified; any part shaded; any spot or stain (outside); raw edges, open seams, thread ends not removed, or loose tension resulting in loose seams, gage of stitching irregular or uneven; any material defects, distorted parts or poor workmanship; any component part omitted, mispl

26、aced, insecure, defective, out of alignment, right and left front or back vent uneven in length when smock is buttoned, size or type not as specified; label missing, incorrect, or illegible; measurements not within the specified tolerances, any requirement omitted or not as specified; bar code omitt

27、ed or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code causes damage to the item; any item not packaged in accordance with contract or purchase order. 5. PACKAGING. The preservation, packing, and marking shall

28、be as specified in the contract or order. 6. NOTES 6.1 Source of Government documents. Copies of military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 6.2 Source of non-Government documents 4 Provided by IHSNot

29、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55123A ASTM Test Methods (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) AATCC Test Method (Applications for copies should b

30、e addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215.) Custodian: Army - GL Navy - NU Air Force - 99 Review Activity: Army - MD Air Force - 82, 45 Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT Project No. 8415-0957 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-