DLA A-A-55102-1995 LINER FOOD INSPECTOR-S SMOCK《食品督察工作服衬垫》.pdf

《DLA A-A-55102-1995 LINER FOOD INSPECTOR-S SMOCK《食品督察工作服衬垫》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-55102-1995 LINER FOOD INSPECTOR-S SMOCK《食品督察工作服衬垫》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、1 INCH-POUND I A-A-55 1 O 2 June 10, 1995 COMMERCIAL ITEM DESCRIPTION LINER, FOOD INSPECTORS SMOCK The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-L-44042 for all Federal agencies. 1. SCOPE. 1.1 Scope. This commercial item descr

2、iption covers a liner intended to provide added warmth to personnel of the Army Medical Services engaged in food inspection activities. 2. CLASSIFICATION. The liner shall be provided in the following sizes: Sma 11 Medium Large Extra Large NOTE: Small, Medium, Large, and Extra Large may be abbreviate

3、d as SM, MED, LG, and XLG. 3. SALIENT CHARACTERISTICS. 3.1 Description. The liner shall be coat length with a snap front closure, waist drawcord, and zippered hood with drawcord around face opening. The drawcords shall be cut in the following lengths for all sizes: two each, 25 2 1/2 inches long for

4、 hood; one each, 56 5 1/2 inches long for waist. All drawcord outlets shall have eyelets which have been reinforced with 1-1/2 x 3/4 pieces of oxford cloth. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be address

5、ed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FQSC, 2800 South 20th Streer, Philadelphia, PA 19145-5099. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networ

6、king permitted without license from IHS-,-,-A-A- 55 1 O 2 The liner shall have a knitted collarette and cuffs, and two side pass throughs. All seams shall be overedged. The liner is intended to be worn with the Smock, Mans, Food Inspectors (See Figure i). 3.2 Materials. 3.2.1 Basic material. The cov

7、er for the batting shall be ripstop nylon cloth, with a pattern of two warp ends woven as one and two filling picks per shed. The color shall be natural (unbleached) and 1.1 ounces per sq. yd. (maximum). There shall be 120 warp yarns per inch and 120 filling yarns per inch. The cloth shall conform t

8、o the following end item test requirements: Characteristic Results Test method Warp Fillina Breaking strength lbs. (min.) 42 42 ASTM D-5035 Dimensional Stability (max.) 2.0% change (see below) 3.2.1.1 Dimensional stability test. The test specimen shall be a square of cloth a minimum 20 by 20 inches.

9、 Before marking and measuring for dimensional change, the specimen shall be in equilibrium with Standard Conditions as defined in FED-STD-191. The specimen shall be laid without tension on flat surface and shall be inscribed with an 18-inch square approximately equidistant from the sdges having side

10、s parallel to the warp and nominal filling directions. The marked specimen shall be laced F for a period of 2 hours. The specimen may be looped over a rod or laid fla,t on a rack both of which shall be low-conductivity (nonmetallic) material and have free air circulation on both sides. Promptly remo

11、ve the specimen from the oven, allow to cool on a flat surface, and then bring to equilibrium under Standard Conditions. Measure each side of the inscribed square for dimensional change in both the warp and filling directions (two measurements each for the warp and filling per specimen). Each change

12、 in dimension shall be reported to the nearest 0.1 percent. The specimen shall also be visually compared with the original unheated cloth for any appreciable distortion or puckering. L/ in a preheated oven and maintained at a temperature of 280 8 2 20 - i/ comparing the tested specimen with the orig

13、inal. If closure inspection is required to make apparent a slight change, the change is not considered ap2rsciable. Appreciable means a change that is immediately noticeable when 3.2.2 Polvester battnq. The batting shall be 10 oz./sq. yd. continuous filament (4.0 to 6.0 denier) or hollow cut staple

14、(5.25 to 6.0 denier), thickness, inches at 0.01 psi. should be a minimum of 1.00. prohibited. The use of any form of polyester waste is t c c P f 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55102 S 9999974 0367557 LTL A-A-55 1 O 2 3.2.3 Thr

15、ead. The thread for seaming and stitching shall be cotton covered, polyester, white, ticket numbers 50, 2 ply and 70, 2 ply, Tex 36 - 45. 3.2.4 Facinus and weits. The material for facings, pocket welts, eyelet reinforcements and when used for waist drawcord tunnel shall be cloth, oxford, nylon, 3 ou

16、nce, natural color, 180 warp yarns per inch and 76 filling yarns per inch. The breaking strength shall be 220 pounds for the warp and 135 pounds for the filling. 3.2.5 Collarette and cuff. The yarn for knitting the cuff and collarette fabric shall be made from natural color, first quality, multifila

17、ment nylon. 3.2.6 Cuff. The cuff shall be made on a circular knitting machine, seamless, with a 1 by 1 rib stitch, and have not less than 14 wales and 26 courses 2er inch. The cuffs shall have a tuck or expanding stitch not less than 1-1/2 or more than 2 inches in length when cut and doubled. The fi

18、nished cuffs shall conform to the following measurements: Cuff measurements Length Folded edge Open edge Tolerance Weight per (inches) (inches) (inches ) ( inches ) dozen pair 7 2-1/2 4 - + 3/8 4 ounces 3.2.7 Collarette. The finished fabric shall be a true 1 by 1 ribbed knit and have a minimum of 12

19、 wales and 26 courses per inch and shall have a finished weight of not less than 8 ounces per square yard of single fabric. 3.2.8 Tape. The tape for waist drawcord tunnel and hanger loop shall be tape, nylon, woven, natural color, 3/4 inch wide, .O15 - .O25 inch thick with a breaking strength of 400

20、 pounds. The tape shall have 150 yarns per warp and 66 yarns per filling. 3.2.9 Cord, nylon. The drawcord for the hood and waist shall be nylon, natural coior with a breaking strength of 95 pounds, (minimum) and elongation of 30 percent (minimum). The length per pound shall be 951: feet (minimum). A

21、fter cord is cut to required length, the ends shai3. be fused to prevent raveling. The construction sh.all conform to the following requirements: Yarn Denier/ply Ply Core 210/3 5 to 7 Sleeve ?0/3 15 to 19 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

22、-,-,- A-A-55102 = 9999974 01b7558 038 = A-A-55 102 3.2.10 Slide fastener. The slide hood shall conform to requirements for type I, style 4, size IM with short tab pull of V-F-106. The fastener chain shall be fabricated of aluminum, brass or zinc. 3.2.10.1 Lensth of slide fasteners. The respective le

23、ngths of the slide fastener shall be 11-1/2 inches for small size, 12 inches for medium size, 12-1/2 inches for large size, and 13 inches for X-large sizes. 3.2.10.2 Slide fastener tape. The tape shall be white cotton. 3.2.11 Snap fasteners. The snap fasteners shall be fasteners, snap, brass, style,

24、 SA, male and female complete, consisting of stud and eyelet- size 1 or 2 and socket conforming to MIL-F-10884. 3.2.12 Eyelets. The eyelets for drawcord outlets shall be brass, conforming to BWE 107 of MIL-E-20652/1. 3.3 Label/markinq. A commercial type label is acceptable, provided that an addition

25、al printed cloth label containing the contractors name, contract number, size and National Stock Number (NSN) is caught on the stitching of the commercial label. The commercial label shall include fiber and laundering information. 3.3.1 Identification, size and instruction labels. The identification

26、, size md instruction labels shall be made on nonwoven, spunbonded polyester cloth, or mildew resistant printed, acrylic coated, impregnated, nonwoven 80/20 polyester/cellulose cloth. The instruction label shall contain the following information: LINER, FOOD INSPECTORS SMOCK 1. Dry liner and smock s

27、eparately when damp or wet. 2. Avoid contact with heated stoves or other heat sources; fabric may fuse. 3. Wash by hand or machine in warm water with mild soap or detergent, Rinse thoroughly and drip or machine dry. DO NOT DRY CLEAN 3.4 Label/taq. Each item shall be individually bar-coded with a pap

28、er tag for personal clothing items. The paper tag shall be standard bleached sulfate having a basis weight of 100 pounds. The paper used for thi tags shall have a smooth finish to accept thermal transfer and direct printing. The tags shall have a hole and shall be attached to each item by a fastener

29、, clearly legible and readable by a scanrier. The bar coding element shall be a 13 digit national stock number (NSN). The bar code type shall be a medium to high code deiisity and shall be located so that it is completely visible on the item when it is folded and/or packaged as specified and so that

30、 it causes no damage to the item. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55102 1999974 0367557 T74 Lg A-A-55 10 2 X-Lg Tolerance 3.5 Patterns. The Government shall furnish a single size pattern. The contractor is responsible for gradin

31、g patterns for additional sizes. The pattern generally provides for a seam allowance of 1/2 inch for joining seams and 1/4 inch for all other seams. Commercial patterns may be used in lieu of the Government furnished pattern provided they conform to the cited design and finished measurements. 28 50

32、17-1/2 3.6 Sizes and measurements. The finished liner shall conform to the measurements below. TABLE I. Finished measurements (inches) 30 - + 3/4 52 2 3/4 17-1/2 2 1/2 1/2 breast measurement i/ c length L/3/ Sleeve length - Sm 24 46 17-1/2 Med 26 48 17-1/2 - i/ Measure at base of armhole, from folde

33、d edge to folded edge, with front closed. - 2/ Measure along center back from hood joining seam to extreme bottom edge of ;iner. - 3/ Measure from base of armhole along inseam to bottom of sleeve, excluding cuff. 4. REGULATORY REOUIREMENTS. The offeror/contractor is encouraged to use recovered mater

34、ials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QUALITY ASSURANCE ?IIOVISIONS 5.1 Certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of

35、 this commercial item description; conforms to the producers ow1 dzwings, specifications, standards and quality assurance practices; and is the same product offered for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance prior to the first deliv

36、ery and thereafter as may be Qtherwise provided for, under the provisions of the contract. 5.2 Market acceptabi.?ity. The iteK cffered, or a generic equivalent, must have been sold to the commercial market or to the Government for at least 2 years. Provided by IHSNot for ResaleNo reproduction or net

37、working permitted without license from IHS-,-,- A-A-55102 I 9999974 0367560 796 I A-A-55 1 O 2 5.3 Visual examination. Liner lots shall be inspected in accordance with “Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control

38、. 5.3.1 Defects. Any hole, c-at, tear; color not as specified; any spot or stain (outside); thread ends not removed; any bartacks missing insecure, or misplaced; any component part or required operation omitted; any draw cord ends not fused, knots omitted; any eyelets missing, defective, or not secu

39、rely clinches; rough or sharp edges on one or more eyelets; label missing; any hood drawcords less than 24-1/2 or more than 25-1/2 inches, or caught by snap fastener; any snap fasteners cap portion less than 7/8 or more than 1-1/8 inch from side or top edge; any slide fastener tape stitched too clos

40、e to metal chain obstructing freedom of slider; any fastener tape set too loose or too tight, causing noticeable bulge on tape or hood; any excessive fullness or puckering on hood at joining to neck incorrect, eyelets on right side are less than 7/8 or more than 1-1/8 inch from side edge, on left si

41、de are less than 1-3/8 or more than 1-5/8 inch from bottom of edge; not centered on facing by more than 1/8 inch; collarette twisted or distorted; hanger ends not caught between collarette twisted or fronts uneven in length when closed; wristlets badly twisted; or illegible measurement of item not a

42、s specified, and any variance not otherwise classified herein; bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code causes damage to the item; any items not packaged in accordance with the contr

43、act or purchase order. 6. PACKAGING 6.1 Preservation, packinq, and markinq. The preservation, packing, and marking shall be as specified in the contract or purchase order. 7. NOTES 7.1 ,Sources of Government documents. Copies of military and Federal documents are available from: Standardization Docu

44、ments Order Desk Bldg. 4D 700 Robbins Avenile Philadelphia, PA 19111-5094 7.2 Sources of Nonqovernment documents ASTM Test Methods (Applications for copies siiuuld be addressed to American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187. ) 6 Provided by IHSNot for Re

45、saleNo reproduction or networking permitted without license from IHS-,-,-A-A-55102 9999974 01b75bL 622 A-A-5 5 1 O 2 ANSI/ASQC 21.4 - Sampling Procedures and Tables for Inspection of Attributes (Applications for copies should be addressed to American National Standards Institute, 11 West 42nd Street

46、, New York, NY 10036-8002.) Custodians: Navy - NU Air Force - 99 Army - GL Review Activities: Coast Guard - CT Air Force - 45 - MD Civil Agency Coordinating Activity GSA - FSS Preparing Activity: DLA - CT (Project No. 8415-0051) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. , , ,_ . 1 I - . FIGURE 1. Liner, Food Inspectors Smock 8 . . . .- - _. . . : Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-