DLA A-A-52079 B-2009 MANTLE ILLUMINATING (GASOLINE LANTERN).pdf

《DLA A-A-52079 B-2009 MANTLE ILLUMINATING (GASOLINE LANTERN).pdf》由会员分享，可在线阅读，更多相关《DLA A-A-52079 B-2009 MANTLE ILLUMINATING (GASOLINE LANTERN).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: STDZNMGTdla.mil or Defense Supply Center Richmond (DSCR), ATTN: DSCR-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616. FSC 6260 INCH-POUND A-A-520

2、79B 19 March 2009 SUPERSEDING A-A-52079A 30 June 1993 COMMERCIAL ITEM DESCRIPTION MANTLE, ILLUMINATING (GASOLINE LANTERN) The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers o

3、ne type of mantle for fuel burning lanterns. 2. SALIENT CHARACTERISTICS 2.1 Design. The mantel shall be commercial, knitted, soft-type. When the mantle is laid flat its dimensions shall approximate 2.87 inches long by 2.25 inches wide with a tolerance of 0.25 inches. 2.2 Mantle. The mantle shall be

4、made from a chemically treated seamless knitted rayon tubing. The closed end of the mantle shall be formed by gathering or pleating the tube and sewing with chemically treated cotton thread. The resulting bag shall be turned so that the end is on the inside. The top section of the mantle shall be tr

5、eated with a chemical solution or material selection to provide hardness and increase the strength and abrasion resistance of this section of the mantle after ignition. Approximately half of this treated band shall be turned in, to form a double thickness. A drawstring shall be threaded around and t

6、hrough the top or head hardened section of the mantle for fastening the mantle to the mantle holder of the lantern. 2.2.1 Seamless knitted tubing. The seamless knitted tubing shall be knit from 150 denier, 42 filament, bright rayon yarn (or equal) using duplex weave. 2.2.2 Instructions. Mantle insta

7、llation instructions shall be included with each unit pack. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52079B 2 3. REGULATORY REQUIREMENTS 3.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximu

8、m extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS 4.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards

9、, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 4.2 Bid sample. Ten mantles shall be submitted for bid sample testing. 4.2.1 Bid sample performance test. Two mantles sha

10、ll be installed and prepared in a commercial lantern according to mantle manufacturers instructions prior to lantern operation. The lantern shall then be lit per the manufactures instructions. The lantern shall be operated for 30 minutes, turned off, and allowed to cool for 30 minutes. This operatio

11、n shall be repeated five times. The other mantle shall be installed and ignited (in pairs of two) in the same manner except they will be ignited only one time. All mantles shall be examined for broken threads and holes. The first set of mantles will be tested for light output. The light output shall

12、 be a minimum of 150 candle power. 4.3 Metric product. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in FED-STD-376, “Preferred Metric Un

13、its for General Use by the Federal Government“, and all other requirements of this CID are met. If a product is manufactured to a metric dimension and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the pro

14、duct is acceptable. The contracting officer has the option of accepting or rejecting the product. 4.4 Market acceptability. The product offered must have been previously sold either to the government or on the commercial market. 5. PACKAGING 5.1 Preservation, packing, and marking. Preservation, pack

15、ing, and marking shall be as specified in the acquisition order (see 6.3(b). 6. NOTES 6.1 Intended use. The mantle is intended for use with a single or double mantle fuel burning lantern. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52079B 3 6

16、.2 Sources of documents. 6.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of FAR documents may be obtained from http:/www.arnet.gov/far/. 6.2.2 Federal standards. Copies of federal standards may be obtained from Ge

17、neral Services Administration, Federal Supply Service, Specification Section, 470 East LEnfant Plaza SW, Suite 8100, Washington, DC 20407. Electronic copies of federal standards may be obtained from http:/assist.daps.dla.mil/. 6.3 Ordering data. The acquisition order should specify the following inf

18、ormation: a. CID document number and revision. b. Preservation, packing, and marking (see 5.1). 6.4 Subject term (key word) listing. fuel knitted rayon tubing yarn MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: Army - GL Navy - CG Air Force - 99 GSA - FAS Review Activity: Army -

19、 CR4 Preparing Activity: DLA - GS2 (Project 6260-2009-003) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-