DLA A-A-50528 A-1992 COAT SHOOTER-S GREEN《爆破手绿色大衣》.pdf

《DLA A-A-50528 A-1992 COAT SHOOTER-S GREEN《爆破手绿色大衣》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-50528 A-1992 COAT SHOOTER-S GREEN《爆破手绿色大衣》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-50528A W 9999974 OLL9b49 2T W COMMERCIAL ITEM DESCRIPTION COAT, SHOOTERS GREEN The General Service Administration has authori Commercial Item Description. d Abstract. This description covers green cotton or cotton shooting coats in an ambidextrous style for hand shooters, intended for wear by ma

2、le personnel Marine Corps. I INCHPOUND 1 A-A-50528A 20 Nov. 1992 Superseding 29 Sept. 1988 A-A- 5 O 5 2 8 he use of this polyester right or left of the US Salient characteristics The shooters coat shall be a single breasted, unlined coat with a five button front closure; cardigan type neck; two-piec

3、e back with bellows at each side and a set-on half-belt; one piece sleeves with elbow pads; a button patch pocket on left side, hemmed on top edge and bartacked corners; a flap with a buttonhole; a shoulder/pulse pad on right and left front; double stitched shoulder, armhole, sleeve, side seams, and

4、 center back seam. The bottom of the coat shall have a 3/4 2 1/8 inch hem. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, At

5、tn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provid

6、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50528A 74 OLL9650 TO1 = A-A-50528A Sizes. The coats shall be available in sizes small, medium, large and extra large. Material. The basic fabric shall be cotton or polyester/cotton sateen cloth, weighing

7、a minimum of seven ounces per square yard dyed to a dark olive green shade and shall be in accordance with the requirements in table I. Cotton duck cloth. The cotton duck cloth which covers the pads shall be an olive green shade to approximate the basic material and shall be in accordance with the r

8、equirements in table II. Table I 1 1. Requirements Test method Weight - 7 oz per sq/yd (min) Breaking strength (lbs, minimum) Warp - 115 Filling - 100 Colorfastness to: Light - (good) Laundering (after 3 cycles) - (good) Perspiration - (good) Crocking - (good) Shrinkage elongation (not more than 2.0

9、% in warp or filling direction) ASTM-D 3776 Option C ASTM-D 5034 - 90 ASTM-D 5034 - 90 AATCC 16A-1988 AATCC 61-1986 AATCC 15-1985 AATCC 8-1988 FED-STD-191/5550 Table II Requirements Test method Weight - 8.25 oz per sq/yd (min) Colorfastness to: Laundering (after 3 cycles) - (good) Crocking - (good)

10、Shrinkage - 2.0 (in warp or filling direction) Breaking strength: Warp - not less than 90% Filling - not less than 85% Felt: Weight (original dry specimen) content (45% min) ASTM-D 3776 Option C AATCC 61-1986 AATCC 8-1988 FED-STD-191/5550 ASTM-D 5034-90 ASTM-D 5034-90 FED-STD-191/2101 FED-STD-191/21

11、01 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50528A W 9999974 0119651 948 A-A-50528A Pads. The pads shall be constructed from 1/4 inch thick felt. The pads shall be cross stitched and edge stitched with a double row of stitching to provid

12、e stability. The area of measurement cited for all pads shall be the center of the length and the center of the width. The elbow pads shall be 8-3/4 inches wide and 17 inches long and shall be placed 1 inch from armhole. The shoulder/pulse pads shall measure approximately 11-1/2 inches wide and 9 in

13、ches long. The shoulder/pulse pad placement shall be 4 inches from front finished edge and 1 inch from shoulder/neckline seam. The pad shall have a slit opening 3 inches from the bottom to allow free arm movement (see figures 1 and 2). Fiqure. The figure is furnished for information purposes only. I

14、f there are any inconsistencies between the written Commercial Item Description and the figure, the written Commercial Item Description shall govern. Pocket and Flap. The pocket shall be placed 3/4 to 1 inch below the shoulder/pulse pad 3 inches over from finished front edge. The finished pocket sha

15、ll measure 6-1/2 2 1/4 inches long and 5-3/4 f. 1/8 inches wide. The pocket flap shall be placed 1/4 to 1/2 inch up from the top of the pocket and should measure 2-1/4 2 1/2 inches long at the center point. Thread. The thread shall be cotton or polyester/cotton and dyed an olive green shade. Buttons

16、. The buttons shall be plastic, 30 line, and an olive green shade. Buttonholes. The buttonholes should be clean cut, eyelet end taper bar type or rectangular with bartacks at each end and properly positioned to fit the 30 line buttons. Label. Each coat shall have a printed or stamped label at the ba

17、ck of the neck containing the size and national stock number (NSN). A printed or stamped label shall be placed inside the right facing near the bottom of the coat containing the contract number and contractors name or a combination label may be used at the back of the neck. Patterns. The government

18、shall furnish a single size pattern. The contractor is responsible for grading patterns for additional sizes. Commercial patterns may be used in lieu of the government furnished pattern provided they conform to the cited design and finished measurements. Provided by IHSNot for ResaleNo reproduction

19、or networking permitted without license from IHS-,-,-A-A-50528A = 9999974 OLL9652 884 A-A-50528A Finished measurements. The finished coat shall conform to the measurements below. Coat measurements L/ Size Back Sleeve length 2/ Waist 3/ length A/ ( inches ) ( inches ) ( inches ) Small 28 19 Medium 28

20、-112 21 Large 29 23 Ex-large 29-1/2 25 23 24 23-1/2 24-1/2 i/ 2/ Tolerance on all measurements: 5 1/2 inch. Back length measurement shall be taken along center back seam from top to bottom edge of coat. 3/ Waist measurement shall be taken along center of belt from folded edge to folded edge of coat

21、with coat buttoned and lying flat. - 4/ Sleeve length measurement shall be taken along the center of sleeve from the shoulder seam of armhole to lower finished end. Workmanship. After completion, the coats shall be thoroughly cleaned and all loose threads, lint and foreign matter removed. The coats

22、shall be uniform in quality and shall be free from irregularities or defects which adversely affect performance, reliability or durability. Contractor certification. The contractor shall certify and maintain inspection records indicating that the product offered meets the salient characteristics of

23、this CID, and that the product conforms to the producers own drawings, specifications standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the

24、 contract. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50528A W 9999974 0119b53 ?LO W A-A-5O528A Qualitv Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description an

25、d that the product conforms to the producers own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contra

26、ct. Reliance on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all products or i supplies submitted to the government for acceptance comply with ) all requirements of the contract. 4 Examination. Coat lots shall be inspected in accordance with “Sampling

27、 Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control Dimensional Examination. The finished coat shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect

28、. The sample unit shall be one coat; the inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. Visual Examination. The coat shall be examined for the defects listed below. The lot size shall be expressed in units of coats. The sample unit is one co

29、at. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 2.5. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50528A W 9999974 OLL9b54 657 D A-A-50528A VISUAL EXAMINA

30、TION Examine Defect Basic fabric color Pads Pocket But tons Seams and stitching Hole, tear, slub, etc, that may develop a hole. Not dark olive green shade. Not cross stitched or edge stitched with double row of stitching. Improperly positioned. Improper size of pads (too large or too small). Pocket

31、or flap poorly shaped or set on crooked, affecting appearance. Too small or large by 1/2 inch or more. Cracked or broken. Not aligned with buttonholes in front or pocket flap causing fronts to twist, pucker or bulging between buttons. Wrong size and shade. Seam twisted, puckered or pleated seriously

32、 affecting appearance. Tight or loose tension causing thread breaks or open seams. Thread breaks not secured by back tacking. Open seam over 1/4 inch. Raw edges over 1/2 inch. Buttonholes Not clean cut (loose threads). Component parts Not proper size. Missing, distorted, misplaced or not as specifie

33、d. Inspection for preparation and delivery. An inspection shall be made to determine whether the packaging, packing, and marking comply with the requirements of the contract or purchase order. Examination for defects shall be in accordance with Table II. For examination of interior packaging, the sa

34、mple unit shall be one shipping container fully prepared for delivery. Sampling shall be in accordance with ANSI/ASQC 21.4. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 with an AQL of 2.5 defects per hundred units. 6 Provid

35、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50528A W 9999974 0339655 593 W A-A-50528A Preparation for delivery defects. Examine Markings Ma teria 1 Workmanship Contents Defects Omitted; incorrect; illegible; improper size, location, sequence, or me

36、thod of application. Any component missing, damaged, or not conforming to applicable requirements stated herein. Inadequate application of components such as incomplete closure of container flaps, loose strapping, or distortion of container. Quantity of container is more or less than required. Gross

37、 weight exceeds requirements of the box specifications. Reuulatorv Reuuirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Preservation, Packinq, and Markinq. The preservation, packing, and marking shall be

38、 as specified in the contract or order. Source of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonuovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures a

39、nd Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5052AA 9999974 0339656 42T

40、m A-A-50528A ASTM-D 3776 - Weight ASTM-D SO34 - Breaking strength (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) AATCC 16 - Colorfastness to Light AATCC 8 - Colorfastness to Crocking: AATCC Crockmeter Method AATC

41、C 61 - Colorfastness to Laundering, Home, and Commercial: AATCC 15 - Colorfastness to Perspiration Accelerated (Applications for copies should be addressed to American I 12215, Triangle Park, NC 27709-2215) i Association of Textile Chemists and Colorists (AATCC), P.O. Box Custodian: Navy - MC Civil

42、Agency Coordinating Activities: GSA-FSS Preparing Activity: DLA - CT 8 Project No. 8415-0882 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5052A 6 Y8ZSOS-Q-Q Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I f3 8 k Lu E;: 0 I LI YSZSO5-V-Y A-A-50528A D 9999974 OLL9658 2T2 = OT Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-