DLA A-A-50473 B-1993 OILERS HAND PUSH-BOTTOM《按键手动加油器》.pdf

《DLA A-A-50473 B-1993 OILERS HAND PUSH-BOTTOM《按键手动加油器》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-50473 B-1993 OILERS HAND PUSH-BOTTOM《按键手动加油器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-504738 9999974 OL44bb0 OTT I Diameter (A) I I I Size I Capacity I I code Iminimum maximumlminimum maximum I I fl oz I inches 1/2 1-1/2 I 1-1/2 3 I1 I I INCH-POUND I A-A-50473B June 21. 1993 SUPERSEDING April 11, 1989 A-A-50473A COMMERCIAL ITEM DESCRIPTION OILERS, HAND, PUSH-BOTTOM The General Se

2、rvices Administration has authorized the use of this commercial item description in preference to Federal Specification GGG-0-592, type I, class A. Abstract. This CID covers the requirements for push-bottom hand oilers. The oiler shall be of cold-rolled steel. The oiler shall consist essentially of

3、a top section with spring-action bottom, a washer, and a threaded removable spout. Salient characteristics. 1. Oiler description. The oiler shall be similar to figure 1. The oiler body and spout shall be connected by means of machine-cut threads in both parts. Material thickness and dimensions for t

4、he oiler shall be in accordance with table I for the size as specified in the contract or order. (fl oz). Oiler capacity requirements shall be measured in fluid ounces TABLE I. Oiler dimensions. Height I Material thickness I (B) /Wall (C) I Bottom (D)I minimum maximum1 minimum I minimum 1 inches I i

5、nches I inches I 1 2-1/2 I 0.022 1 0.012 I 3 I 0.022 I 0.012 I 4 I 0.022 I 0.012 I 12 12 4 13 4 12 13 15 10 13 5 12 4 I 0.022 I 0.014 I I4 110 16 I 3-1/2 5-1/2 I 2 /Beneficial comments (recommendations, additions, deletions) and any pertinent1 Jdata which may be of use in improving this document sho

6、uld be addressed to: I Iconmanding Officer (Code 156), Naval Construction Battalion Center, I 1621 Pleasant Valley Road, Port Hueneme. CA 93043-4300. I FSC 4930 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networkin

7、g permitted without license from IHS-,-,-A-A-50473B 9999974 0344663 T35 A-A-50473B 5.r 2. Oiler body. The oiler body shall consist of a one-piece seamless cold-rolled steel top section and a spring-action bottom. The top section and bottom shall be securely fitted to each other with a strong and lea

8、kproof joint. less than 3/4 inch in diameter. This opening shall be either fitted with a solid-brass collar, or the top part of the body opening shall be reinforced with a solid-metal neck in a manner to prevent weakening connections when the threads are cut. The body shall have an opening in the to

9、p of not 3. Oiler spout. The oiler spout shall be of cold-rolled steel; length shall be between 1-1/2 and 4 inches, between 4 and 6 inches, between 6 and 9 inches, or between 9 and 12 inches, as specified in the contract or order. The spout shall be either straight or bent, as specified in the contr

10、act or order. having machine-cut threads suitable for engagement in the threaded opening of the oiler body. The spout seam shall be welded, brazed, or silver-soldered. Lead-tin solders are not acceptable. The fitting of the collar/neck and spout shall afford a strong and leakproof joint. The spout s

11、hall be fitted with a solid-brass bushing 4. Oiler finish. The oiler shall be polished or copper plated and finished with a coat of lacquer or varnish or baked-on enamel finish. 5. Washer. The washer shall be impervious to oil and shall have such oil-sealing qualities so as to prevent leakage at the

12、 threaded connection. 6. Marking. Each oiler shall be marked in a plain and permanent manner with the manufacturers name or with a trademark of such known character that the source of manufacture may be readily determined. Contractor certification. The contractor shall certify and maintain substanti

13、ating evidence that the product offered meets the salient characteristics of this CID and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices and is the same product sold in the commercial marketplace. The Government reserves the right

14、to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided

15、 they fall within specified tolerances using conversion tables contained in the latest revision of FED-STD-376, and all other requirements of this CID are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request sh

16、ould be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. Regulatory requirements. In accordance with Section 23.403 of the Federal Acquisition Regulations, the Governments policy is to acquire ite

17、ms composed of the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition without adversely affecting performance requirements or exposing the suppliers employees to undue hazards from the recovered materials. 2 Provided by IHSNot for R

18、esaleNo reproduction or networking permitted without license from IHS-,-,-A-A-504738 9999974 0144662 971 A-A-50473B PackaPinn. DackinP and markinq. The packaging, packing, labeling, and marking shall be as specified in the contract or order. CID based Dart identification number (PIN). The following

19、PIN procedure is for O Government purposes and does not constitute a requirement for the contractor. The PIN to be used for oilers acquired to this CID is created as follows: A50473 - X - X I II CID part number I II Size code (see table 11) II Spout length code (see table III) I 1. Size code. The si

20、ze code of the oiler, relative to its capacity, is identified by a single number (see table II). TABLE II. Size code to capacity. Size I Capacity range I code I fluid ounces I 1 I 1/2 to 1-1/2 I 2 12 to 4 I 3 15 to 10 I I 4 I 10 to 16 I 2. Spout length code, The spout length code is identified by a

21、cingle letter (see table III). TABLE III. Spout length code to spout lennth. Ispout length code I Spout length I to 6 I I A I 1-1/2 to 4 I to 9 I I B 14 to 12 I I C 16 I D 19 3, Cross-referencing of PIN. The PIN of oilers in this CID differs from the previous edition in the following respects: A-A-5

22、0473A A-A-50473B Finish number Finish 1. Polished copy clear lacquer or varnish 2. Brass coated or plated w/clear lacquer or varnish 3. Copper coated or plated w/clear or varnish 4. Lacquer or opaque 5. Nickel plated 6. Baked on enamel 3 Not designated Not designated Not designated Not designated No

23、t designated Not designated Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50473B 9999974 0144663 808 ! 4 A-A-50473B Spout number 1. 2 inches 2, 3 inches 3. 4 inches 4. 5 inches 5. 6 inches 6. 9 inches 7. 12 inches Size number 1. 1/2 oz 3. 1-1/2

24、 oz 2. 1 oz 4, 1/4 pint 5. 1/3 pint 6. 1/2 pint 7. 3/4 pint 8. 1 pint Spout length - code A - 1-1/2 to 4 inches B - 4 to 6 inches C - 6 to 9 inches D - 9 to 12 inches Size code 1 - 1/2 to 1-1/2 fl oz 2 - 2 to 4 fl oz 3 - 5 to 10 fl oz 4 - 10 to 16 fl OZ Class number Class 1. Class A 2. Class B Not d

25、esignated Not designated Notes. Purchaser should specify size of oiler, length of spout, straight or bent spout, and PIN required for a specific procurement. FED-STD-376 is available from Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. MILITARY INTERE

26、STS: CIVIL AGENCY COORDINATING ACTIVITY: Custodian GSA - FSS Navy - YD PREPARING ACTIVITY: Review Activity Navy - YD DLA - CS (Project 4930 - 0373) User Activities Army - EA Navy - MC Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50473B m 9999974 0344664 744 m A-A-50473B FIGURE 1 . O i ler conf i Qurat i on. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-