DLA A-A-50118 B-2000 STRAPS CRAMPONS《有金属钩的带子》.pdf

《DLA A-A-50118 B-2000 STRAPS CRAMPONS《有金属钩的带子》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-50118 B-2000 STRAPS CRAMPONS《有金属钩的带子》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDA-A-50118BOctober 10, 2000SUPERSEDINGA-A-50118AFebruary 21, 1990COMMERCIAL ITEM DESCRIPTIONSTRAPS, CRAMPONSThe General Services Administration has authorized the use of this Commercial ItemDescription for all Federal agencies.1. SCOPE. This commercial item description covers the requiremen

2、ts for the cramponstraps, which are intended to keep the crampon firmly affixed to the soldiers footwear.2. CLASSIFICATION. The crampon straps shall be of one type and size.3. SALIENT CHARACTERISTICS.3.1 Design and construction. The crampon straps when used with A-A-50117;Crampons, Hinged, shall be

3、neoprene coated nylon webbing with brass center barbuckles, copper or brass rivets, and corrosive resisting steel or brass slide buckles. Thebuckle frame shall have a minimum breaking strength of 350 pounds when tested asspecified in paragraph 3.2. The strap widths shall be + 0.008 inch. Straps for

4、one pairof crampons shall consist of the following pieces:Quantity Description2 Center bar buckles riveted to a strap 5 +1, -0 inches in length as measuredfrom the center of the center bar buckle to the tip of the strap.2 Center bar buckles riveted to a strap 7 +1, -0 inches in length as measuredfro

5、m the center of the center bar buckle to the tip of the strap.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data whichmay improve this document should be sent to: Defense Personnel Support Center, Clothing andTextiles Directorate, Attn: DSCP-COET, 700 Robbi

6、ns Ave, Philadelphia, PA 19111-5096.AMSC N/A FSC 8465Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50118B2Quantity Description4 Straps 36 +1, -0 inches in length with 12 holes no larger than 1/8 inch andlarge enough to be compatible with the ce

7、nter bar buckles. The holes shallstart within 1 to 1 inches from the end of the straps and be evenlyspaced a distance of 5 + 3/16 inches from the first hole.8 Slide buckles with an inside width of 5/8 + 1/16 inch.The crampon straps shall also be furnished with assembly and lacing instructions.3.2 Te

8、sting. Randomly select two sets of crampon straps from the end item lot and testeach of the buckles for breaking strength by placing a loop of the strap material aroundeach end of the buckle, fastening the loops in the jaws of a tensile testing machine with acapacity greater than 700 pounds and pull

9、ing the entire assembly. The jaws of the tensiletesting machine shall be set at a separation of 5 inches and shall separate at a rate of 0.5inches per minute. Failure of the buckle at a strength less than 350 pounds constitutesfailure of the test. Crampon straps shall be compatible with A-A-50117; C

10、rampons,Hinged. Any failure shall be cause for rejection of the end item lot from which thesample was selected.4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to userecovered materials to the maximum extent practicable, in accordance with paragraph23.403 of the Federal Acquisition R

11、egulation (FAR).5. QUALITY ASSURANCE PROVISIONS.5.1 Product conformance. The products provided shall meet the salient characteristics ofthis commercial item description, conform to the producers own drawings,specifications, standards, and quality assurance practices, and to be the same productoffere

12、d for sale in the commercial market. The government reserves the right to requireproof of such conformance.5.2 Visual examination. Each item shall be examined for the defects listed below.Defects. Finish not smooth and adherent; not free of burrs, rough spots, sharp edges,slivers, flat areas or proj

13、ections; any component missing or not specified type; anycomponent fractured, split, dented, bowed, malformed, damaged or loose; rivets notproperly peened; nylon webbing has cuts and/or nicks; not compatible with A-A-50117;Crampons, Hinged; markings in wrong location, incomplete, illegible, or not a

14、s specified.5.3 Dimensional examination. The crampon straps shall be examined without damagingor disassembling the item. Any dimension not within the specified tolerances shall beclassified as a defect. The lot size shall be expressed in units of straps. The sample unitshall be one set of straps.Pro

15、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50118B35.4 Acceptance criteria. Acceptance criteria shall be as specified in the contract orpurchase order.6. PACKAGING.6.1 Preservation, packing, and marking. The preservation, packing, and marking sh

16、all beas specified in the contract or order.7. NOTES7.1 Source of Government documents. Copies of military and Federal documents areavailable from:Standardization Documents Order DeskBldg. 4D700 Robbins AvenuePhiladelphia, PA 19111-50947.2 Ordering data. Acquisition documents should specify the foll

17、owing:a. Title, number, and date of this document.b. Type required (see paragraph 2)7.3 Sources of products known to meet this CID. Below is only a sampling of knownsuppliers and not an all-inclusive list. Similar items may be considered acceptable.1. Adventure Tech, Inc4124 N. Burns RoadSpokane, WA

18、 992162. Climb High1861 Shelburne RoadShelburne, Vermont 054823. REI (Recreational Equipment Incorporated)Sumner, WA 98352MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITYGSA - FSSCustodiansArmy GL PREPARING ACTIVITY:Air Force 11 DLA-CTNavy - NUReview Activities Project NumberNavy MC 8465-0330Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-