DLA A-A-50021 B-2001 GLOVES MEN-S CLOTH LEATHER PALM WITH GAUNTLET《中号针织腕带 皮革手掌的男式布手套》.pdf

《DLA A-A-50021 B-2001 GLOVES MEN-S CLOTH LEATHER PALM WITH GAUNTLET《中号针织腕带 皮革手掌的男式布手套》.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-50021 B-2001 GLOVES MEN-S CLOTH LEATHER PALM WITH GAUNTLET《中号针织腕带 皮革手掌的男式布手套》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH/POUND A-A-50021B MAY 18, 2001 SUPERSEDING A-A-50021A JAN. 30, 1990 COMMERCIAL ITEM DESCRIPTION GLOVES, MENS; CLOTH, LEATHER PALM WITH GAUNTLET The General Services Administration has authorized the use of this commercial item description as a replacement for Type II, Class 1 of JJ-G-451. 1. SC

2、OPE. This document covers gloves for use as work gloves in the following type and style as specified: Type I - Gunn cut pattern with gauntlet and knuckle reinforcement Style 1 - 5 inch long gauntlet 2. SALIENT CHARACTERISTICS 2.1 Description. The gloves will utilize the Gunn pattern, with a leather

3、palm with gauntlet and knuckle reinforcement. 2.2 Material. 2.2.1 Leather. The leather for the front of fingers, back of fingertips, front and back thumb, knuckle reinforcement piece, palm with gauntlet reinforcement extension, and the protective welt for the seam joining fingers to palm will be chr

4、ome tanned, flesh split from cattlehide bends. and will be suitable for use in gloves. Both sides of the leather will be smooth and free of loose flesh. Middle splits, head splits, belly splits and shoulder splits will not be used. All leather parts, except the welt, will be 2-1/2 to 3-1/2 ounces th

5、ick when tested as specified in ASTM-D-1814. (Note: One ounce is equivalent to 1/64 inch). The welt will be 1-1/2 to 2-1/2 ounces thick when tested as specified in ASTM-D-1814. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this docume

6、nt should be sent to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DPSC-COCT, 700 Robbins Avenue, Philadelphia, PA 19111-5092. AMSC N/A FSC 8415 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50021B22.2 Cloth. The

7、 back of the glove will be a napped cotton canton flannel, minimum weight 10.0 ounces per square yard, with the napped surface facing the hand. The palm, front of the fingers, and front of the thumb will be lined with cotton flannel, minimum weight 6.0 ounces per square yard when tested as specified

8、 in ASTM-D-3776. The napped surface of the lining will face the hand. The gauntlet will be composed of a two thickness plain weave construction fabric of cotton or spun polyester yarns securely bonded together with synthetic resin, synthetic rubber, or natural rubber. The bonded fabric will weigh no

9、t less than 16.0 ounces per square yard when tested as specified in ASTM-D-3776. The top edge of the gauntlet will be overedge stitched or bound with a bias cut cotton binding. 2.3 Dimensions. The finished gloves will conform to the measurements specified below. Any variation on the same pair of mor

10、e than 1/4 inch for any dimension will be scored as a defect. Location Inches Tolerance (inch) A. Overall length, tip of 2nd (middle) finger to top of cuff. 12-1/2 + 1/2 B. Hand length; tip of 2nd (middle) 7-1/2 + 1/4 finger to wrist seam C. Width of glove across palm 5-1/4 + 1/4 _ 2.4 Labels. A com

11、mercial-type label is acceptable, provided that an additional printed cloth label containing the contractors name, contract number, size and National Stock Number (NSN) is caught on the stitching of the commercial label. The commercial label will include fiber and laundering information. 2.4.1 Label

12、/tag. Each item will be individually bar-coded with a paper tag for personal clothing items. The paper tag will be standard bleached sulfate having a basis weight of 100 pounds. The paper used for the tags will have a smooth finish to accept thermal transfer and direct printing. The tags will have a

13、 hole and will be attached to each item by a fastener, clearly legible and readable by a scanner. The bar coding element will be a 13 digit national stock number (NSN). The bar code type will be a medium to high code density and will be located so that it is completely visible on the item when it is

14、 folded and/or packaged as specified and so that it causes no damage to the item. 3. REGULATORY REQUIREMENTS. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance require

15、ments, and promotes economically advantageous life cycle costs. 4. QUALITY ASSURANCE PROVISIONS 4.1 Product conformance. The products provided will meet the salient characteristics of this commercial item description and will conform to the producers own drawings, specifications, standards, and qual

16、ity assurance practices. The Government reserves the right to require proof of such conformance. 4.2 Examination. Each glove will be inspected for visual and dimensional attributes in accordance with ANSI/ASQC Z1.4 - Sampling Procedures and Tables for Inspection by Attributes, published by the Ameri

17、can Society for Quality Control. The lot size will be Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50021B3expressed in units of one glove. The sample unit will be one glove and the selection will be by pairs. 4.2.1 Visual examination. Each glo

18、ve will be examined for the defects listed below: Any hole, cut, or tear; color not as specified; any part shaded; any spot or stain (outside); raw edges, open seams, thread ends not removed, or loose tension resulting in loose seams; any material defects, distorted parts or poor workmanship; any co

19、mponent part omitted; for leather: unhealed scratch, grub, tick marks, open veins, or clearly noticeable fat wrinkles; label missing, incorrect, or illegible; measurement of item not as specified; bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible;

20、bar code not visible on folded, packaged item; bar code causes damage to the item; any items not packaged in accordance with the contract or purchase order. (Up to 3 needle holes are acceptable). 4.2.2 Dimensional examination. The gloves will be measured for overall length, hand length and hand widt

21、h for conformance to the dimensions listed in 2.3. 4.3 Acceptance criteria. Acceptance criteria will be as specified in the contract or purchase order. 5. PACKAGING. The preservation, packing, and marking will be as specified in the contract or order. 6. NOTES 6.1 Source of Government documents. Cop

22、ies of military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 6.2 Source of non-Government documents ANSI/ASQC Z1.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should b

23、e addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018-3308). MILITARY INTERESTS: Custodians CIVIL AGENCY COORDINATING Army - GL ACTIVITY: Navy - MC GSA - FSS Air Force 99 Review Activities PREPARING ACTIVITY: Army - MD DLA - CT Navy - CG Air Force - 82 Project 8415-

24、0202 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50021B4STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, boththe document number and revision letter should be

25、given.2. The submitter of this form must complete blocks 4, 5, 6, and 7 and send topreparing activity.3. The preparing activity must provide a reply within 30 days from receipt of theform.NOTE: This form may not be used to request copies of documents, nor to requestwaivers, or clarification of requi

26、rements on current contracts. Comments submitted onthis form do not constitute or imply authorization to waive any portion of thereferenced document(s) or to amend contractual requirements.I RECOMMEND A CHANGE:1. DOCUMENT NUMBERA-A-50021B2. DOCUMENT DATE(YYYYMMDD)2001/05/183. DOCUMENT TITLEGLOVES, M

27、ENS; CLOTH, LEATHER PALM WITH GAUNTLET4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheetsas needed.)5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Last, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Inclu

28、de Area Code)(1) Commercial(2) DSN(If applicable)7. DATESUBMITTED(YYYYMMDD)8. PREPARING ACTIVITYa. NAMEDEFENSE SUPPLY CENTER PHILADELPHIADSCP-COCTb. TELEPHONE (Include Area Code)(1) Commercial (2)DSN-444-2426(215) 737-2426c. ADDRESS (Include Zip Code)700 Robbins Ave (Bldg 6, C&T)PHILADELPHIA, PA 191

29、11-5092IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT:Defense Standardization Program Office (DLSC-LM)8725 John J. Kingman Road, Suite 2533Fort Belvoir, Virginia 22060-6221Telephone (703) 767-6888 DSN 427-6888DD Form 1426, FEB 1999 (EG) PREVIOUS EDITION IS OBSOLETEWHS/DIOR, Feb 99Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-