DIN EN ISO 2078-2016 Textile glass - Yarns - Designation (ISO 2078 1993 + Amd 1 2015) German version EN ISO 2078 1994 + A1 2015《纺织玻璃纤维 纱线 标识(ISO 2078 1993+Amd 1-2015) 德文版本EN ISO 20.pdf

《DIN EN ISO 2078-2016 Textile glass - Yarns - Designation (ISO 2078 1993 + Amd 1 2015) German version EN ISO 2078 1994 + A1 2015《纺织玻璃纤维 纱线 标识(ISO 2078 1993+Amd 1-2015) 德文版本EN ISO 20.pdf》由会员分享，可在线阅读，更多相关《DIN EN ISO 2078-2016 Textile glass - Yarns - Designation (ISO 2078 1993 + Amd 1 2015) German version EN ISO 2078 1994 + A1 2015《纺织玻璃纤维 纱线 标识(ISO 2078 1993+Amd 1-2015) 德文版本EN ISO 20.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、May 2016 English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 59.100.10!%UT*“2504907www.din.deDIN E

2、N ISO 2078Textile glass Yarns Designation (ISO 2078:1993 + Amd 1:2015);English version EN ISO 2078:1994 + A1:2015,English translation of DIN EN ISO 2078:2016-05Textilglas Garne Bezeichnung (ISO 2078:1993 + Amd 1:2015);Englische Fassung EN ISO 2078:1994 + A1:2015,Englische bersetzung von DIN EN ISO 2

3、078:2016-05Verre textile Fils Dsignation (ISO 2078:1993 + Amd 1:2015);Version anglaise EN ISO 2078:1994 + A1:2015,Traduction anglaise de DIN EN ISO 2078:2016-05SupersedesDIN EN ISO 2078:1994-12www.beuth.deDocument comprises 10 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-lang

4、uage original shall be considered authoritative.05.16 DIN EN ISO 2078:2016-05 2 A comma is used as the decimal marker. National foreword This document (EN ISO 2078:1994 + A1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics”, in collaboration with Technical Committee CEN/TC 249 “Pla

5、stics” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was DIN-Normenausschuss Kunststoffe (DIN Standards Committee Plastics), Working Committee NA 054-02-02 AA Verstrkte Kunststoffe und hrtbare Harze. The start and finish of text introduced or altered by amendme

6、nt is indicated in the text by tags !“. For the International Standards referred to in this standard there are no national standards available, except for that below, which corresponds as follows: ISO 472 DIN EN ISO 472 Amendments This standard differs from DIN EN ISO 2078:1994-12 as follows: a) Ame

7、ndment A1:2015 concerning Table 1 has been incorporated. Previous editions DIN 60850: 1960-01, 1975-03, 1976-02 DIN 60850-1: 1987-03 DIN EN ISO 2078: 1994-12 National Annex NA (informative) Bibliography DIN EN ISO 472, Plastics Vocabulary EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 2078

8、 October 1994 + A1 December 2015 ICS 59.100.10 English Version Textile glass Yarns Designation (ISO 2078:1993 + Amd 1:2015) Verre textile Fils Dsignation (ISO 2078:1993 + Amd 1:2015) Textilglas Garne Bezeichnung (ISO 2078:1993 + Amd 1:2015) EN ISO 2078:1993 was approved by CEN on 1994-08-25 and Amen

9、dment A1:2015 on 2015-10-03. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national s

10、tandards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language an

11、d notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hunga

12、ry, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Managemen

13、t Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2078:1994 + A1:2015 E 2DIN EN ISO 2078:2016-05 EN ISO 2078:1994 + A1:2015 (E)Contents Page Foreword to EN ISO 2078:1994 . 3 !Europ

14、ean foreword to EN ISO 2078:1994/A1:2015 4 1 Scope 5 2 Normative references 5 3 Definitions 5 4 Designation of a yarn 5 4.1 Elements of the designation 5 4.1.1 Glass used . 5 4.1.2 Type of yarn . 5 4.1.3 Nominal diameter of fibre . 5 4.1.4 Linear density, direction and amount of twist and number of

15、components . 6 4.1.5 Manufacturers code . 6 4.2 Designation of different types of textile glass yarn . 6 4.2.1 Strands . 6 4.2.2 Silvers . 6 4.2.3 Single yarns . 6 4.2.4 Folded (plied) (doubled) yarns . 7 4.2.5 Cabled yarns 7 4.2.6 Multiple wound yarns 8 4.2.7 Rovings. 8 4.2.8 Chopped strands . 8 Fo

16、reword to EN ISO 2078:1994 International Standard ISO 2078:1993 Textile glass; yarns; designation which was prepared by ISO/TC 61 Plastics of the International Organization for Standardization, has been adopted by Technical Committee CEN/TC 249 Plastics as a European Standard. This European Standard

17、 shall be given the status of a national Standard, either by publication of an identical text or by endorsement, and conflicting national Standards withdrawn, by April 1995 at the latest. In accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to implement this Eur

18、opean Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of the International Standard ISO 2078:1993 was approved by CEN as a European St

19、andard without any modification. 3DIN EN ISO 2078:2016-05EN ISO 2078:1994 + A1:2015 (E)!European foreword to EN ISO 2078:1994/A1:2015 This document (EN ISO 2078:1994/A1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics”

20、 the secretariat of which is held by NBN. This Amendment to the European Standard EN ISO 2078:1994 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be withdrawn at the

21、latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national s

22、tandards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania

23、, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement noticeThe text of ISO 2078:1993/Amd 1:2015 has been approved by CEN as EN ISO 2078:1994/A1:2015 without any modification.“ 4DIN EN ISO 2078:

24、2016-05 EN ISO 2078:1994 + A1:2015 (E)1 Scope This International Standard specifies a System of designating textile glass yarns including Single, multiple-wound, folded (plied), cabled and textured yarns, Strands, slivers and rovings based on their Iin- ear density expressed in the tex System. This

25、International Standard applies the rules of the Single-to-fold designation given in ISO 1139 to these textile glass products. 2 Normative references The following Standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of

26、publi- cation, the editions indicated were valid. All Standards are subject to revision, and Parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most re- cent editions of the Standards indicated below. Members of IEC and ISO mainta

27、in registers of cur- rently valid International Standards. ISO 2:1973, Textiles - Designa tjon of the direction of twist in yarns and rela ted products. ISO 472: 1988, Plastics - Vocabulary. ISO 1139: 1973, Textiles - Designation of yarns. 3 Definitions For the purposes of this International Standar

28、d, the definitions given in ISO 2 and ISO 472 apply. 4 Designation of a yarn 4.1 Elements of the designation According to the definition given in ISO 1139, the designation of a yarn (Single yarn, Strand, sliver, . . . . roving) is a condensed technical description contain- ing the following elements

29、. 4.1.1 Glass used One or several letters, to specify the glass used by the manufacturer (see table 1). 4.1.2 Type of yarn A letter to describe the type of yarn: - C (continuous) for continuous-filament yarns, - D (discontinuous) for staple-fibre yarns. NOTE 7 These letters are placed in the first g

30、roup, as it is of special importante in the case of textile glass to dis- tinguish between continuous-filament yarns and staple fibre yarns; their use makes it unnecessary to indicate the num- ber of filaments, preceded by the Symbol f, as proposed in ISO 1139. 4.1.3 Nominal diameter of fibre A numb

31、er, consisting of one or two figures, giving the nominal diameter, in micrometres, of the filament or staple fibre. 5DIN EN ISO 2078:2016-05EN ISO 2078:1994 + A1:2015 (E)4.1.4 Linear density, direction and amount of twist and number of components Some, or all, of the following elements, as in ISO 11

32、39: a) a number giving the linear density expressed in the tex System. lt is strongly recommended that the tex be used as the basic unit, in which case the word “tex” tan be omitted from the designation (if multiples or submultiples of the tex are used, these units shall be indicated after the value

33、 given for linear density); b) the direction(s) of twist;) c) the amount(s) of twist, expressed in turns per metre, for the twist of the final Stage, and (if necessary) in the full designation, for the twist of each intermediate Stage; d) the number of components in folding (plying) or cabling. 4.1.

34、5 Manufacturers code If desired, the designation may also include the manufacturers Code, permitting the incorporation of any complementary information that does not appear among the previous elements, for example the type of size and the Overall linear density. If it is included, the manufacturers

35、code shall be placed either before or after the designation as defined below and never between the elements of the designation for exam- ple in the case of folded (plied) yarns having dissimilar components. 4.2 Designation of different types of textile glass yarn Subclauses 4.2.1 to 4.2.8 give the e

36、lements that shall appear in the designation of various types of glass yarn. 4.2.1 Strands a) the type of glass used; b) the letter C for continuous-filament yarn; c) the nominal diameter , in micromet me nts, followed by a space; res, of the fila- d) the linear density, preferably in tex see 4.1.4

37、a). EXAMPLE EC10 40 4.2.2 Slivers a) the type of glass used; b) the letter D (discontinuous) for staple-fibre yarns; c) the nominal diameter, in micrometres, of the sta- ple fibres, followed by a space; d) the linear density, preferably in tex see 4.1.4 a). EXAMPLE ED7 190 4.2.3 Single yarns 4.2.3.1

38、 Single continuous-filament yarns a) the type of glass used; b) the letter C for continuous-filament yarn; c) the nominal diameter, in micrometres, of the fila- ments, followed by a space; d) e) f) EXAMPLE NOTE and Strands For twisting yarn 4.2.3.2 Single staple-fibre yarns a) the type of glass used

39、; b) the letter D (discontinuous) for staple-fibre yarns; c) the nominal diameter, in micrometres, of the sta- ple fibres, followed by a space; d) the linear density, preferably in tex see 4.1.4 a), followed by a space; e) the direction of twist, followed by a space; f) the amount of twist, expresse

40、d in turns per metre. EXAMPLE ED7 190 Z 160 1) If the yarn has been subjected to a twisting Operation, this shall be indicated by the direction of twist followed by the degree of twist. If the designation does not include any mention of twist, this shall always be taken to signify the absence of any

41、 twisting Operation. 6DIN EN ISO 2078:2016-05 EN ISO 2078:1994 + A1:2015 (E)4.2.3.3 Textured yarns a) the type of glass used; b) the letter C or D for the designation of the original yarn (see 4.1.2); c) the nominal diameter, in micrometres, of the fila- ments, followed by a space; d) the linear den

42、sity, preferably in tex see 4.1.4 a), before texturing, followed by a space; e) the linear density, preferably in tex see 4.1.4 a), after texturing, preceded by the letter T. EXAMPLE EC9 340 T352 4.2.4 Folded (plied) (doubled) yarns2) 4.2.4.1 Folded (plied) yarns having identical components a) Full

43、designation: 1) the designation of the Single continuous- filament or staple-fibre yarns used, in accord- ante with 4.2.3.1 or 4.2.3.2, followed by a space; 2) a multiplication sign, x, followed by a space; 3) the number of Single continuous-filament or staple-fibre yarns, followed by a space; 4) th

44、e direction of the folding (plying) twist, fol- lowed by a space; 5) the amount of folding (plying) twist, expressed in turns per metre. EXAMPLES ED7 190 Z 160 x 2 S 260 b) Simplified designation: 1) the designation of the Single continuous- filament or staple-fibre yarns used, in accord- ante with

45、4.2.3.1 or 4.2.3.2, without indication of the direction or amount of twist the twist of folded (plied) yarns is generally balanced, followed by a space; 2) a multiplication sign, x, followed by a space; 3) the number of Single continuous-filament or staple-fibre yarns, followed by a space; 2) This t

46、erm is defined in ISO 1139. 4) the direction of the folding (plying) twist, fol- lowed by a space; 5) the amount of folding (plying) twist, expressed in turns per metre. EXAMPLES EC934x2S150 EC9 190 x 2 S 260 4.2.4.2 Folded (plied) yarns having dissimilar components a) the designations of the Single

47、 continuous-filament yarns used, in accordance with 4.2.3.1, joined by a plus sign, +, preceded and followed by a space, the whole being placed in parentheses and fol- lowed by a space; b) the direction of the folding (plying) twist, followed by a space; EXAMPLE EC934Z150x2S100x3Z80 b) Simplified de

48、signation: The twist of cabled yarns is generally balanced, and in most cases it is not necessary to know the direction and the amount of twist of each of the intermediate stages; consequently, the simplified designation for a cabled yarn shall only show the direction and the amount of final twist.

49、The simplified designation shall therefore consist of the following elements: 1) the designation of the Single continuous- filament yarns, in accordance with 4.2.3.1, omitting the direction and the amount of twist, followed by a space; for each intermediate Stage: 7DIN EN ISO 2078:2016-05EN ISO 2078:1994 + A1:2015 (E)2) a multiplication sign, X, followed by a space; 3) the number of yarns involved, followed by a space; for the final Stage: 4) a multiplic