DIN EN 12561-8-2011 Railway applications - Tank wagons - Part 8 Heating connections German version EN 12561-8 2011《轨道交通 油罐车 第8部分 加热连接器 德文版本EN 12561-8-2011》.pdf

《DIN EN 12561-8-2011 Railway applications - Tank wagons - Part 8 Heating connections German version EN 12561-8 2011《轨道交通 油罐车 第8部分 加热连接器 德文版本EN 12561-8-2011》.pdf》由会员分享，可在线阅读，更多相关《DIN EN 12561-8-2011 Railway applications - Tank wagons - Part 8 Heating connections German version EN 12561-8 2011《轨道交通 油罐车 第8部分 加热连接器 德文版本EN 12561-8-2011》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、October 2011 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、 45.060.20!$u|“1822589www.din.deDDIN EN 12561-8Railway applications Tank wagons Part 8: Heating connectionsEnglish translation of DIN EN 12561-8:2011-10Bahnanwendungen Kesselwagen Teil 8: HeizanschlsseEnglische bersetzung von DIN EN 12561-8:2011-10Applications ferroviaires Wagons citernes Partie 8:

3、Raccordements de rchauffageTraduction anglaise de DIN EN 12561-8:2011-10SupersedesDIN EN 12561-8:2004-07www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1009.11DIN EN 12561-8:2011-10 A comma is used as the decimal marker. National f

4、oreword This standard has been prepared by Technical Committee CEN/TC 256 “Railway applications” (Secretariat: DIN, Germany), Working Committee WG 20 “Tank wagons” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Fahrweg und Schienenfahrze

5、uge (Railway Standards Committee), Working Committee NA 087-00-10 AA Gterfahrzeuge. Amendments This standard differs from DIN EN 12561-8:2004-07 as follows: a) the requirements have been brought in line with the modified RIV; b) the standard has been editorially revised. Previous editions DIN 26024:

6、 1965-10, 1973-08, 1982-01, 1992-04, DIN EN 12561-8: 2004-07 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12561-8 June 2011 ICS 45.060.20 Supersedes EN 12561-8:2004English Version Railway applications - Tank wagons - Part 8:Heating connections Applications ferroviaires - Wagons citernes -

7、Partie 8 : Raccordements de rchauffage Bahnanwendungen - Kesselwagen - Teil 8: HeizanschlsseThis European Standard was approved by CEN on 3 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

8、 of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germ

9、an). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia

10、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZAT

11、ION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12561-8:2011: E2 Contents Page Foreword 31 Scope 42 Normati

12、ve references 43 Terms and definitions .44 Requirements .45 Positioning of connections .46 Connection .56.1 Dimensions .56.2 Tightening device 66.3 Test pressure of connections .67 Materials .78 Marking .7Bibliography 8Figures Figure 1 Positioning of connections 5 Figure 2 Dimensions of connections

13、.6 Figure 3 Example of tightening device 6 EN 12561-8:2011 (E) DIN EN 12561-8:2011-10 3 Foreword This document (EN 12561-8:2011) has been prepared by Technical Committee CEN/TC 256 “Raiway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a n

14、ational standard, either by publication of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of

15、 patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12561-8:2004. This European Standard Railway applications Tank wagons consists of the following parts: Part 1: Identification plates for tank wagons for the car

16、riage of dangerous goods; Part 2: Bottom emptying devices for liquid products including vapour return; Part 3: Bottom filling and emptying devices for gases liquefied under pressure; Part 4: Devices for top filling and emptying of liquid products; Part 5: Devices for vapour return while filling or e

17、mptying of liquid products; Part 6: Manholes; Part 7: Platforms and ladders; Part 8: Heating connections. The changes made during this revision are editorial because of the change of the title of part 1 and the necessary updates of references. According to the CEN/CENELEC Internal Regulations, the n

18、ational standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan

19、ds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 12561-8:2011 (E) DIN EN 12561-8:2011-10 4 1 Scope This European Standard specifies positioning of connections, connection dimensions and coupling tightening devices for connections of ste

20、am heating installations used on tank wagons. This European Standard applies to new tank wagons built after the 1st January 2010. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. Fo

21、r undated references, the latest edition of the referenced document (including any amendments) applies. EN 14564, Tanks for transport of dangerous goods Terminology 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14564 and the following apply. 3.1 hea

22、ting installation device heating the tank contents and/or discharge equipment with steam 3.2 steam trap self contained valve which automatically drains the condensate from a steam containing enclosure while remaining tight to live steam, or if necessary, allowing steam to flow at a controlled or adj

23、usted rate 4 Requirements The extremities of the heating installation shall be fitted as follows: each inlet shall be fitted with a valve PN 16, and a connection according to Clause 6; each outlet shall be fitted with a valve PN 16 or a steam trap. In order to drain condensate the outlet shall be si

24、tuated at the lowest point of the steam heating installation. This outlet shall not be obstructed when the outlet valve is open. It shall be directed to the ground in such a way as not to present a danger to personnel or damage on brake parts or to other wagon equipment. 5 Positioning of connections

25、 Except by agreement between customer and manufacturer, the connections shall be positioned entirely within the areas shown in Figure 1. EN 12561-8:2011 (E) DIN EN 12561-8:2011-10 5 Dimensions in millimetres Key 1 Where tank wagons are fitted with top connections, they shall be positioned within thi

26、s area 2 Where tank wagons are fitted with bottom connections, they shall be positioned on both sides within this area Figure 1 Positioning of connections The steam connections shall not infringe the loading gauge. Spaces for connections may need to be different for domestic traffic in Great Britain

27、 (see Technical Specification for Interoperability for Freight Wagons). 6 Connection 6.1 Dimensions Except for other types of connections agreed between the customer and the manufacturer, the dimensions of the connection shall be as shown in Figure 2. EN 12561-8:2011 (E) DIN EN 12561-8:2011-10 6 Dim

28、ensions in millimetres Figure 2 Dimensions of connections 6.2 Tightening device The connection to the steam supply pipe shall be made in a leak-tight manner. An example of a tightening device is shown in Figure 3. Figure 3 Example of tightening device 6.3 Test pressure of connections The test pressu

29、re of the connections shall be at least equal to the test pressure of the steam heating installation. EN 12561-8:2011 (E) DIN EN 12561-8:2011-10 7 7 Materials The materials of the fittings shall exhibit a suitable degree of safety in accordance with the maximum permissible working pressure and tempe

30、rature of the heating installation. At these maximum working conditions, the materials shall be compatible with the steam where they come in contact with it. 8 Marking The maximum allowable working pressure of the heating installation shall be clearly marked on the tank wagon close to the connection

31、s. NOTE Regulation should require other marking in case of hot parts. Where the heating device can also be used for heating tank equipment, a diagrammatic representation of the use of the different devices shall be fitted on the tank wagon close to the connections. EN 12561-8:2011 (E) DIN EN 12561-8

32、:2011-10 8 Bibliography 1 EN 12972, Tanks for transport of dangerous goods Testing, inspection and marking of metallic tanks 2 RID, Regulations concerning the International Carriage of Dangerous Goods by Rail1)implementing Commission Directives 2003/28/EC and 2003/29/EC 3 TSI Rolling Stock Freight W

33、agons 4 UIC 503, Continental wagons running in Great Britain (via the Channel Tunnel and on Network Rail Infrastructure) General conditions (reference profile, axle-load, etc.) for the acceptance, in international traffic with Great-Britain, of 2-axle and bogie wagons registered with other UIC member Rus2)5 UIC 573, Technical conditions for the construction of tank wagons 1) Commonly known as RID. 2) May be purchased from: Railway Technical Publications (ETF), 16 rue Jean Rey, F-75015 Paris. EN 12561-8:2011 (E) DIN EN 12561-8:2011-10