CIE 62-1984 Lighting for Swimming Pools (E)《游泳池用照明》.pdf

《CIE 62-1984 Lighting for Swimming Pools (E)《游泳池用照明》.pdf》由会员分享，可在线阅读，更多相关《CIE 62-1984 Lighting for Swimming Pools (E)《游泳池用照明》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、COMMISSION INTERNATIONALE DE LECLAIRAGE INTERNATIONAL COMMISSION ON ILLUMINATION INTERNATIONALE BELEUCHTUNGSKOMMISSION LIGHTING FOR SWIMMING POOLS PUBLICATION CIE NO 62 (1984) BUREAU CENTRAL DE LA CIE 52, BOULEVARD MALESHERBES 75008 PARIS - FRANCE COPYRIGHT International Commission on IlluminationLi

2、censed by Information Handling Services CIE 62 Bq .I 9006145 O002601 TOB This report has been prepared by CIE Technical Cormnittee 4.4 Sports Lighting. It has been approved by the majority of the Technical Committee and is recommended for study and application. This report is not an Officially Agree

3、d CIE Recommendation approved by the National Committees of the Member Countries of the CIE. It should be noted that any recommendations in this report are advisory and not mandatory. The latest CIE Proceedings or CIE Journal should be consulted regarding the current status of this report and possib

4、le subsequent amendments. Ce rapport a t prpar par le Comit Technique 4.4 LEclairage pour la pratique des sports. I1 a windows and is not recommended as a means of correction for poorly designed electric lighting. - Ensure that the lighting of the pool surrounds and spectator galleries does not crea

5、te disturbing reflections. Any adjacent areas, separated from the main hall by glazed walls, should also be designed to avoid spurious reflections. 3. DAYLIGHT 3.1. REQUIREMENTS FOR INDOOR POOLS The primary objective is to ensure the safety of users by providing good visual conditions for everyone.

6、The daylighting design must therefore contribute to this requirement, by providing a sufficient level of illuminance and a good penetration of light into the water. The design aims therefore are: - to ensure a minimum horizontal illuminance, of say 250 lux, at any point over the pool. This illuminan

7、ce should be achieved for a crtai depending on the seasons. - to ensure the penetration of light into the water. - to avoid glare due to direct or reflected sunlight and moving surface of the water or high contrast between w 3.2. INFLUENCE OF LIGHTING ON ARCHITECTURAL DESIGN I number of hours per da

8、y, skylight reflected in the ndows and their surrounds. Steps should be taken to make the best use of daylight. In open air pools, during the site selection process, the best location would be the site where shadows of the surrounding buildings are not cast across the pool. Also, spectator accommoda

9、tion and divers should not directly face into the sun. In the case of daylit indoor pools, or those with sliding roofs, the building orientation should be selected, if possible, to provide visual contact with the external environment and ensure penetration of sunlight and the variations of daylight

10、to enhance the general atmosphere. The design of the pool hall might be such that daylight will be the only source of interior lighting for as long a time as possible each day. To provide full recreational facilities the indoor or sliding-roofed pool may include other areas such as open air pools, a

11、nd sun-bathing areas. In towns it will sometimes be expedient to use existing parks, gardens and sports grounds as sites for new swimming pool s. 3.3. WINDOWS OR WALLS Glazing installed in one side elevation of the building to obtain maximum daylight and to contribute towards a pleasant atmosphere i

12、s sometimes not sufficient to obtain a satisfactory level of illuminance. Additional glazing is often necessary on one or both end elevations, or by installing roof-lights fitted with diffusing materials and louvres to attenuate direct sunlight. Solar radiation will of course raise the temperature i

13、nside the building. In some cases this effect can be used to advantage, in others, the solar gain must be reduced to COPYRIGHT International Commission on IlluminationLicensed by Information Handling Services CIE 62 84 7006245 0002bLO TL0 avoid thermal discomfort of the occupants, particularly the p

14、ermanent pool staff. Glazing orientation which does not permit entry of direct sunlight can be used successfully in climates where direct sunshine is undesirable. In the winter, thermal losses from large areas of glazing can be excessive; to reduce the cost of heating and to ensure the comfort of us

15、ers by avoiding the “cold wall“ effect, double or triple glazing should be used. As will be appreciated from the details in 2.2, low level windows which provide visual contact with the exterior, are in the least effective position to achieve light penetration into the water and are therefore most li

16、kely to be the source of high luminance reflections on the surface of the pool. A direct view of the sun and excessive luminance contrast can be avoided by the use of external shades, baffles or tinted glass. Internal roller blinds or adjustable venetian blinds achieve the same result. Although both

17、 of these devices can present maintenance problems they also help at night to reduce losses due to the low reflectance of the glazing and so provide more pleasing luminance ratios when the hall is illuminated only by electric lighting. Glare from the water is-experienced when the windows are on the

18、far side of the pool to the viewing position. The instructor or attendant will operate under the best conditions if he has his back to the window as from this position he sees no reflections of the windows in the water surface (Fig.3). The same applies to spectator accommodation, but this is often d

19、ifficult to achieve. The penetration of light into water will be improved by the use of roof- complement the side lighting windows. For general comments on the problems associated with the daylight design where colour television coverage is required, see 4.2.4. 3.4. DAYLIGHT ILLUMINANCE ights to of

20、pool halls The prediction of natural lighting inside a building is complicated because the light source is from the outside and daylight varies with time, season and location. The principles, and methods of daylight design will be found in CIE Publication No.16 Daylight, 7970. In order to reach the

21、level of daylight illuminance specified for roofed swimming pools, the dimensions of windows and roof lights have to be determined to give a daylight factor which meets the design requirements. This is computed according to the location concerned, arriving at an economic balance between daylight and

22、 electric lighting (e.g.the requirements might be not to use electric lighting for 80% of hours of use of the swimming pool between 09.00 and 17.00 hours). 3.5. AVAILABILITY OF DAYLIGHT CIE Publication No. 16 gives the necessary information to set up the reference value of the external illuminance f

23、rom an overcast sky. This reference value (Fig.4 and Table 1) which is likely to be achieved or exceeded during a given percentage of daytime hours, is given in terms Of iatitwde between 50 and 70 north and south. The curves refer to various percentages (95, 90, 85, 80, 70 and 60 %) for a period bet

24、ween 09.00 and 17.00 hours thus for a latitude of 45O the reference value of external illuminance achieved for 80% of this period is 10000 lux. To maintain a minimum level of 250 lux inside the building the minimum daylight factor would be: 250 x 100 10,000 = 2,5% A more general means of specifying

25、illuminance on a horizontal plane under an overcast sky is given in Fig.5 as a function of the height of the sun above the horizon. -6- COPYRIGHT International Commission on IlluminationLicensed by Information Handling Services1400 1300 1200 1100 1000 950 900 850 800 750 700 I :i: 550 5 500 F Q Z 45

26、0 z 3, 400 -1 380 2 360 340 c- 320 300 280 260 240 220 21 o 200 190 180 170 160 150 140 130 CIE 62 84 900bl145 0002bLL 957 W 1700 for which levels of illumination Percentage of hours between O 900 it is also necessary for the referee and spectators to see fast movements in a game of water polo, the

27、judges and spectators having accurately to determine when swimmers touch the pool side, or correctly execute tumble turns during races or to see details of movement in a diving competition. Added to this the spectators often have to see this detail from a considerable distance. Measuring device -7 O

28、 Figure 6. Method of measuring illuminance at a distance 0,2 m above the water surface. -9- COPYRIGHT International Commission on IlluminationLicensed by Information Handling Services CIE 62 84 9006145 0002634 666 spec ta tors The illuminance recommended in the following table is the average maintai

29、ned service horizontal illuminance, measured at a level of 0,2m above the water surface (Fig.6) and on the pool surrounds. Throughout the life of the installation, loss of light output will occur due to lamp lumen maintenance and the accumulation of dirt on luminaires. The extent of this light loss

30、will depend upon local conditions and therefore the initial illuminance, for a new installation should be 1.2 to 1.5 times higher than the service illuminance given in Table 2. Tab1 e 2 Recommended Servi ce t 11 uminance ( 1 ux) 200 Competition (1) Swimming, water polo, and Diving (2) Instruct i on

31、y trai ni ng y water polo, and diving 500 300 (1) The World Swimming Association (Federation Internationale de Natation, FINA) specify a requirement of 400 lux. (2) It is important to obtain in the diving area a vertical illuminance of at least 200 lux in the directions of the judges and spectators.

32、 Competition divers can be distracted by high brightness images of luminaires reflected in the pool, particularly if these are close to the point where the diver enters the water. 4.1.1. Uniformity The uniformity of illuminance is most important on the pool surrounds. In these areas, the following u

33、niformity ratio should be achieved:- Where there are practical limitations a uniformity ratio of up to 2 is acceptable over the water area. These limits ?f illuminance, in themselves, are not the decisive factors for the quality of the illumination. The luminance and colour of the various vertical s

34、urfaces largely decide the subjective impression given by an interior. As mentioned in 1.2 it is particularly important to avoid high luminance on walls as these are more likely to cause unacceptable reflected glare from the pool surface. 4.1.2. Lamps - colour of light In principle, lamps providing

35、good colour rendering should be used. Generally these are covered by CIE Colour Rendering Groups 7 and 2, but some lamps from group 3 can also be considered. for the higher illuminance levels or where a blend with daylight is required, lamps of a colour temperature above 4000K are sometimes favoured

36、. However, the warmer col our appearance of lamps with lower colour temperatures around 3000K are often preferred. In certain cases, the combination of lamps can give very pleasant effects if their light is suitably blended in the occupied space. The high luminous efficacy and long life of tubular f

37、luorescent lamps or HID lamps -10- COPYRIGHT International Commission on IlluminationLicensed by Information Handling Servicesusually provide the most economic solution. The final choice of the light source will depend upon many factors including the hours of use each year, initial cost versus opera

38、ting cost, light control, switching requirement and colour quality. (See also 4.2.1.). 4.1.3. Luminaires The lighting of outdoor pools can be achieved with standard floodlighting equipment and conventional maintenance techniques are also applicable. For indoor pools, however, the high temperature an

39、d humidity conditions often combined with chemical corrosion require luminaires which are designed specifically to operate efficiently and survive mechanically in these onerous condi ti ons . In cases where the pool hall design includes a sealed false ceiling below an access void, the problems are l

40、east severe as only the underside of the bezel holding a sealed cover to the luminaire needs to withstand the conditions in the pool hall. All maintenance can be carried out from the ceiling void which, if it is dry and well ventilated, presents no special problems. For reasons of cost, as well as s

41、tructural and architectural requirements, it is more usual to install complete luminaires within the pool hall. It is advisable that totally enclosed luminaires should be used; these restrict the deposition of dirt onto the lamp and optical surfaces and also in the rare event of lamp breakage, the g

42、lass will be contained within the luminaire. Due to humidity and condensation, the luminaires must resist the.ingress of moisture to a minimum standard such as IP23. (Reference: IEC 529 : 1976 - Classification of degrees of protection provided by enclosures). Standard stove enamel paint finishes on

43、mild steel will not withstand the corrosive attack present. Adequate protection is usually provided by the use of high quality paint finishes on protected metalwork or luminaires constructed in glass reinforced plastic or cast aluminium. It is of course essential that any attachments, exposed bolts,

44、 screws, hinges or supporting metalwork should be as well protected from attack as the main body of the luminaire. The positioning of 1 umi nai res should al so take account of access requirements for maintenance, cleaning and relamping. For this reason, luminaires should not be positioned over the

45、pool unless access catwalks, gantries or rear access from a ceiling void is available. These requirements tend to lead to 1 ighting equipment being positioned over the side of the pool and particularly where mounting height is limited this can lead to problems of reflection in the water. To avoid th

46、is, particular attention must be paid to the light distribution of the luminaire and this will be discussed in the following section which covers a range of lighting techniques which can be used in swimming pools. 4.2. PRINCIPLES OF ELECTRIC LIGHTING One common requirement of outdoor and indoor pool

47、s is that the lining of the pool basin should be of high reflectance in order to achieve a luminance which is as high as possible. Nevertheless the lighting systems used for outdoor and indoor swimming pools are fundamentally different, and therefore it is suitable to treat them separately. 4.2.1. O

48、utdoor pools The usual method is to mount luminaires on masts located on the pool surround. The mounting height depends on their distance from the sides of the pool. In order to achieve adequate light penetration into the water the angle of incidence at the far side of the pool should preferably be

49、50 but not greater than 60. This also ensures that only low luminance images of the floodlights occur in the water. See Fig. 1. The small dimensions -11- COPYRIGHT International Commission on IlluminationLicensed by Information Handling Servicesof the light sources produce only small areas of reflection on the water separated by large areas of dark sky. This produces a low average water surface luminance. In such a case, underwater lighting will not improve the visibility and is therefore unnecessary. ,Suitable light sources are metal halide or high pressure so