CEN TS 1401-2-2012 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2 Guidance for assessment of confo.pdf

《CEN TS 1401-2-2012 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2 Guidance for assessment of confo.pdf》由会员分享，可在线阅读，更多相关《CEN TS 1401-2-2012 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2 Guidance for assessment of confo.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPlastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)Part 2: Guidance for assessment of conformityPD CEN/TS 1401-2

2、:2012National forewordThis Published Document is the UK implementation of CEN/TS 1401-2:2012.It supersedes DD ENV 1401-2:2001, which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee PRI/88/1, Plastics piping for non-pressure applications.A list of organizatio

3、ns represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012 ISBN

4、978 0 580 73651 3 ICS 23.040.20; 93.030Compliance with a British Standard cannot confer immunity from legal obligations.This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 May 2012.Amendments issued since publicationDate Text affectedPUBLISH

5、ED DOCUMENTPD CEN/TS 1401-2:2012TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 1401-2 May 2012 ICS 23.040.01; 93.030 Supersedes ENV 1401-2:2000English Version Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chlorid

6、e) (PVC-U) - Part 2: Guidance for assessment of conformity Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement enterrs sans pression - Poly(chlorure de vinyle) non plastifi (PVC-U) - Partie 2 : Guide pour lvaluation de la conformit Kunststoff-Rohrleitungssy

7、steme fr erdverlegte drucklose Abwasserkanle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN on 6 September 2011 for provisional application. The period of validity of this

8、CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as f

9、or an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the n

10、ational standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swit

11、zerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

12、Ref. No. CEN/TS 1401-2:2012: EPD CEN/TS 1401-2:2012CEN/TS 1401-2:2012 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Abbreviated terms 10 5 General . 10 6 Testing and inspection . 10 6.1 Material specification . 10 6.2 Grouping 11 6.2.1

13、 General . 11 6.2.2 Size groups 11 6.2.3 Fitting groups 12 6.3 Type testing . 12 6.4 Batch release tests . 15 6.5 Process verification tests 17 6.6 Audit tests . 18 6.7 Indirect tests 20 6.8 Test records 20 Annex A (informative) Basic test matrix 21 Bibliography . 22 PD CEN/TS 1401-2:2012CEN/TS 1401

14、-2:2012 (E) 3 Foreword This document (CEN/TS 1401-2:2012) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the elements of this document may be the subject of

15、 patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes ENV 1401-2:2000. Compared with ENV 1401-2:2000, the following changes have been made: a) Use of the template drafted by CEN/TC 155/WG 21 for assessment of conformi

16、ty documents (change of “Terms and definitions“ and addition of 1 column “Sampling procedures“ in Tables); b) Introduction of “Limits of addition of PVC reprocessed and recycled material“ in a separate table (Table 2); c) Addition of an informative Annex A: Basic test matrix. EN 1401, Plastics pipin

17、g systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U), consists of the following Parts: Part 1: Specifications for pipes, fittings and the system; Part 2: Guidance for the assessment of conformity. According to the CEN/CENELEC Internal Regulations, t

18、he national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

19、Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 1401-2:2012CEN/TS 1401-2:2012 (E) 4 Introduction Figures 1 and 2 are intended to provide general information on the concept of testing and organisation of those te

20、sts used for the purpose of the assessment of conformity. This part of EN 1401 details the applicable characteristics to be assessed as well as the frequency and sampling of testing for each type of test, i.e. type testing (TT), batch release test (BRT), process verification test (PVT) and audit tes

21、t (AT). A typical scheme for the assessment of conformity of compounds/formulations, pipes, fittings, assemblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer PD CEN/TS 1401-2:2012CEN/TS 1401-2:2012 (E) 5 A typical scheme for the as

22、sessment of conformity of compounds/formulations, pipes, fittings, assemblies by manufacturers, including a third-party certification, is given in Figure 2. Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including a third-party certification PD CEN/TS 1401-2:2012CEN/TS 1

23、401-2:2012 (E) 6 1 Scope This Technical Specification gives guidance for the assessment of conformity of compounds/formulations, products and assemblies in accordance with EN 1401-1. It applies to those compounds/formulations, products and assemblies intended to be included in the manufacturers qual

24、ity plan as part of the quality management system and for the establishment of third-party certification procedures. NOTE 1 It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements of EN ISO 9001 1. NOTE 2 If third-party certification is

25、 involved, it is recommended that the certification body is accredited to either EN 45011 2, EN 45012 3 or EN ISO/IEC 17021 4, as applicable. NOTE 3 In order to help the reader, a basic test matrix is given in Annex A. In conjunction with EN 1401-1 (see Foreword), this Technical Specification is app

26、licable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) used for the following puposes: for non pressure underground drainage and sewerage outside the building structure (application area code “U“), reflected in the marking of products by “U“; for non-pressure underground draina

27、ge and sewerage for both buried in ground within the building structure (application area code “D“) and outside the building structure (application area code “U“), reflected in the marking of products by “UD“. 2 Normative references The following documents, in whole or in part, are normatively refer

28、enced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1401-1:2009, Plastics piping systems for non-pressure underground drain

29、age and sewerage Unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes, fittings and the system ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 3 Terms and definitions For

30、the purposes of this document, the terms and definitions given in EN 1401-1:2009 and the following apply. 3.1 certification body impartial body, governmental or non-governmental, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules

31、of procedure and management Note 1 to entry: A certification body is preferably accredited to EN 45011 2. 3.2 inspection body impartial organisation or company approved by the certification body as possessing the necessary competence to verify and/or to carry out initial type testing, audit testing

32、and inspection of the manufacturers factory production control in accordance with the relevant standard Note 1 to entry: An inspection body is preferably accredited to EN ISO/IEC 17020 5. PD CEN/TS 1401-2:2012CEN/TS 1401-2:2012 (E) 7 3.3 testing laboratory laboratory which measures, tests, calibrate

33、s or otherwise determines the characteristics of the performance of materials and products Note 1 to entry: In the context of this part of EN 1401, the materials and products can be subjected to type testing, batch release testing, process verification testing, audit testing and/or witness testing,

34、as applicable. Note 2 to entry: A testing laboratory is preferably accredited to EN ISO/IEC 17025 6. 3.4 quality management system management system to direct and control an organization with regard to quality Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 1. 3

35、.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type testing TT testing performed to verify that the material, product, joint or assembly is capable of conforming to the requirements g

36、iven in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are done regularly. 3.7 batch release test BRT test performed by or on behalf of the manufacturer on a batch o

37、f compound/formulation or products, which needs to be satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by or on behalf of the manufacturer on compound/formulation, products, joints or assemblies at specific intervals to confirm that the proce

38、ss continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release batches of compound/formulation or products; rather, they are carried out as a measure of process control. 3.9 audit test AT test

39、performed by a test laboratory on behalf of an inspection body or certification body to confirm that the compound/formulation, product, joint or assembly continues to conform to the requirements given in the relevant standard and to provide information to assess the effectiveness of the quality mana

40、gement system 3.10 indirect test IT test performed by or on behalf of the manufacturer, different from that specified test for that particular characteristic, having previously verified its correlation with the specified test PD CEN/TS 1401-2:2012CEN/TS 1401-2:2012 (E) 8 3.11 witness test WT test ac

41、cepted by an inspection or a certification body for type testing and/or audit testing, which is carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or certification body, qualified in testing 3.12 material generic term for compounds/formulations group

42、ed by families, expressed by generic names, e.g. polypropylene, stainless steel, brass or EPDM SOURCE: European Commission, Directorate-General for Enterprise and Industry, Sub-group on Product Testing Procedures (EC, DG ENT and IND, SG PTP). 3.13 compound/formulation clearly defined homogenous mixt

43、ure of base polymer with additives, i.e. anti-oxidants, pigments, stabilizers and others, at a dosage level necessary for the processing and the intended use of the final product 3.14 material batch clearly identified quantity of a given homogeneous compound/formulation manufactured under uniform co

44、nditions and defined and identified by the compound/formulation manufacturer 3.15 product pipe or fitting, of a clearly identified type, intended to be a part of a piping system which the manufacturer puts on the market 3.16 product batch clearly identified collection of products, manufactured conse

45、cutively or continuously under the same conditions, using the same compound/formulation conforming to the same specification Note 1 to entry: The production batch is defined and identified by the product manufacturer. 3.17 lot clearly identifiable sub-division of a batch set apart for inspection pur

46、poses 3.18 sample one or more products drawn from the same production batch or lot, selected at random without regard to their quality Note 1 to entry: The number of products in the sample are the sample size. 3.19 acceptable quality limit AQL quality level that is the worst tolerable process averag

47、e when a continuing series of lots is submitted for acceptance sampling Note 1 to entry: See ISO 2859-1, ISO 3951-1 8, ISO 3951-2 9, ISO 3951-3 10 and ISO 3951-5 11. Note 2 to entry: The designation of an AQL does not imply that a manufacturer has the right, knowingly, to supply any non-conforming u

48、nit of product. PD CEN/TS 1401-2:2012CEN/TS 1401-2:2012 (E) 9 3.20 inspection level relationship between the lot or batch size and the sample size Note 1 to entry: See ISO 2859-1. 3.21 limiting quality (acceptance sampling) quality level, when a lot is considered in isolation, which, for the purpose

49、s of acceptance sampling inspection, is limited to a low probability of acceptance Note 1 to entry: See ISO 2859-2 7. 3.22 group collection of similar products from which samples are selected for testing purposes 3.23 component product manufactured out of a specific compound/formulation, brought to the market as part of another product or as a spare part 3.24 joint connection between two products 3.25 assembled product assembled final product using two or more single parts 3.26 thermoplastics fabricated fitting