CECC 96 601-2002 Blank Detail Specification Slide switches《空白详细规范 滑动开关》.pdf

《CECC 96 601-2002 Blank Detail Specification Slide switches《空白详细规范 滑动开关》.pdf》由会员分享，可在线阅读，更多相关《CECC 96 601-2002 Blank Detail Specification Slide switches《空白详细规范 滑动开关》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS CECC 96601:2002 Blank Detail Specification: Slide switches The European Standard CECC 96601:2002 has the status of a British Standard ICS 31.220.20 BS CECC 96601:2002 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 25 Marc

2、h 2003 BSI 25 March 2003 ISBN 0 580 41473 6 National foreword This British Standard is the official English language version of CECC 96601:2002. The UK participation in its preparation was entrusted to Technical Committee EPL/23, Switches for appliances and electronic equipment, which has the respon

3、sibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “Int

4、ernational Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a

5、British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related internationa

6、l and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 23 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issue

7、d since publication Amd. No. Date CommentsBLANK DETAIL SPECIFICATION CECC 96 601 SPCIFICATION PARTICULIRE CADRE VORDRUCK FR BAUARTSPEZIFIKATION October 2002 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrot

8、echnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. CECC 96 601:2002 E English version Blank Detail Specification: Slide switches Spcification particulire

9、cadre: Interrupteurs glissire Vordruck fr Bauartspezifikation: Schiebeschalter This Blank Detail Specification was approved on 1991-07-15. Up-to-date lists and bibliographical references of other blank detail specifications relating to EN 196000:1992 and CECC 96 600:1994 may be obtained on applicati

10、on to the Central Secretariat or to any CENELEC member. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sw

11、eden, Switzerland and United Kingdom. CECC 96 601:2002 - 2 - Contents Foreword . 3 1 Basic information 6 1.1 General. 6 1.2 Range and variants available . 6 2 Ratings and characteristics . 6 2.1 Electrical ratings 6 2.2 Environmental ratings. 6 2.3 Mechanical characteristics. 7 2.4 Electrical charac

12、teristics 7 3 Marking information 7 4 Ordering information. 7 5 Related documents .7 6 Certified test records 8 7 Structural similarity. 8 8 Delayed delivery 8 9 Additional information (Not for inspection purposes except where stated). 8 10 Test schedule. 8 - 3 - CECC 96 601:2002 Foreword This Blank

13、 Detail Specification has been prepared by the former CENELEC/TC CECC/SC 23 JX, Switches and sensors. The text of this specification was circulated for voting as document CECC(Secretariat)2417. Based on the voting report circulated as document CECC(Secretariat)2842, it was approved for printing as C

14、ECC 96 601 on 1991-07-15. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2003-05-01 latest date by which the national standards conflicting with the EN have to be withdrawn (

15、dow) 2003-05-01 NOTE This specification is published in English only. _ CECC 96 601:2002 - 4 - Key for page 3 The numbers between square brackets on page 3 correspond to the following information which shall be given. Identification of the harmonized detail specification 1 The name of the National S

16、tandards Organization under whose authority the detail specification is published, followed by the manufacturers name and address if appropriate. 2 The CECC symbol and the number allocated by the CECC General Secretariat. 3 The number and year of availability of the EN (or CECC) generic or sectional

17、 specification; also national reference if different. 4 If different from the CECC number, the national number, date of issue and any further information required by the national system, together with any amendment numbers. Identification of the slide switch 5 A statement of the class of switch, as

18、listed in 1.2 of EN 196000:1992 (CECC 96 000). 6 Information on principal features of construction, such as provision of illumination, sealing, special mounting or termination facilities. It shall be stated if the switch is suitable for printed wiring applications. See 1.3.4 of EN 196000:1992. For 5

19、 and 6, the text shall be suitable for an entry in CECC 00 200 and CECC 00 300. 7 An outline drawing and main dimensions which are of importance for interchangeability, and/or reference to the appropriate national or international document for outlines. Alternatively, this drawing may be given in an

20、 annex. Dimensions shall be given in millimetres. 8 Level of quality assessment, in accordance with 3.4 of EN 196000:1992. 9 The principal ratings and characteristics of the switch. Those parameters which are not subject to lot-by-lot or periodic inspection shall be clearly identified as such. - 5 -

21、 CECC 96 601:2002 Recommended layout for detail specifications for switches of assessed quality 1 Page of CECC 96 601 - 2 ELECTRONIC COMPONENT OF ASSESSED QUALITY: DETAIL SPECIFICATION IN ACCORDANCE WITH EN 196000:1992 3 4 (CECC 96 000) CECC 96 600:1994 OUTLINE AND DIMENSIONS (mm) SLIDE SWITCH 5 (St

22、atement of the class of switch) First angle projection PRINCIPAL CONSTRUCTIONAL FEATURES 7 6 LEVEL OF QUALITY ASSESSMENT 8 NOTE Other shapes are permitted within the (Application dimensions given. range/performance) PRINCIPAL RATINGS AND CHARACTERISTICS (A table of basic dimensions, ratings and char

23、acteristics is required. Variants may be given in annexes to the detail specification). 9 Information about manufacturers who have components qualified to this detail specification is available in the current CECC 00 200. CECC 96 601:2002 - 6 - 1 Basic information 1.1 General A statement of the prin

24、cipal usage features of the device; for example Panel mounting, high current, extended life. 1.2 Range and variants available To include such details as number of circuits, types of contacts, number of indexing positions and distances between two indexed positions; for example 2 circuits, shorting,

25、non-shorting 6 positions x 5,08 mm. 2 Ratings and characteristics Additional parameters may be stated where relevant. Values for all parameters shall be selected as prescribed in 2.1 of CECC 96 600. Ratings and characteristics are required to be stated only if called up to the test schedule for the

26、relevant assessment level. 2.1 Electrical ratings Maximum switched voltage (and - V a.c.and/or d.c. minimum switched voltage, if applicable) Rated voltage - V a.c. and/or d.c. Maximum switched current (and - A a.c. and/or d.c. minimum switched current if applicable) Maximum switched power - VA a.c.

27、and/or d.c. 2.2 Environmental ratings Climatic category -/-/- Shock severity -m/s 2 ; -ms; -shocks in each plane or Bump severity -m/s 2 ; -bumps; duration of each bump 6 ms Vibration 10 Hz to - Hz; d i s p l a c e m e n t 0 , 7 5 m m ; acceleration 98 m/s (10 g); duration - Sealing - kPa (- mbar) c

28、onditions to be stated in accordance with 4.3.14 of EN 196000:1992 - 7 - CECC 96 601:2002 2.3 Mechanical characteristics Operating force -N (min.), -N (max.) Mechanical endurance - operations without load Robustness of actuator - N 2.4 Electrical characteristics Electrical endurance - cycles conditi

29、ons to be stated Maximum initial contact resistance -M conditions to be stated Maximum final contact resistance -M Minimum initial insulation resistance -M conditions to be stated Minimum final insulation resistance -M resistance Voltage proof -V r.m.s. in accordance with 4.3.4 of EN 196000:1992 Cap

30、acitance -pF conditions to be stated 3 Marking information In accordance with 2.4 of EN 196000:1992. 4 Ordering information Ordering for slide switches covered by this specification shall contain the following information: Number of the detail specification; Details of manufacturers codes for specif

31、ic variants. If appropriate. Information on the codes for variants may take the form of an annex showing a typical ordering sheet 5 Related documents EN 196000:1992 (originally CECC 96 000 Issue 2, 1992). Any other documents referred to in this specification shall be listed. CECC 96 601:2002 - 8 - 6

32、 Certified test records State either not required or required in accordance with 3.3 of CECC 96 600. If certified test records are required their contents shall be defined. 7 Structural similarity State either not applicable or to be applied in accordance with 3.2 of CECC 96 600. If applied, details

33、 of the grouping procedures shall be given. 8 Delayed delivery Either state in accordance with 3.6 of CECC 96 600, or state any deviation therefrom. 9 Additional information (Not for inspection purposes except where stated) The following optional details may be given; this information may be present

34、ed in the form of an annex. Unchecked parameters: information concerning factors (such as materials and flammability) which are not subject to regular quality conformance inspection but which may be of significance in selecting a switch for an application. Special contractual information: any additi

35、onal information demanded by special contractual requirements and which is required to be verified by a stated inspection procedure. Application details: any other information intended to assist the user in the application of the components. 10 Test schedule The pro-forma test schedules given in the

36、 sectional specification shall be used as directed by the sectional specification and this BDS. The test schedules for lot by lot and periodic testing are given as pro-forma schedules in Tables 1 and 2 of this BDS. They may be reproduced in the detail specification, if not then reference to them sha

37、ll be made in the detail specification. - 9 - CECC 96 601:2002Table 1 Test schedule for quality conformance inspection, assessment level D Group A (non-destructive) To be conducted on a sampling basis, lot-by-lot Sub Test and measurements group Title a Conditions of test ILo r See individual test me

38、thods i a in 4.3 of EN 196000:1992 AQL Requirements A1 Visual examination a 1.1 Note 1 I 1,5 % Note 1 A2 Outline dimensions a 1.2 Note 1 S3 1% Note 1 A3 Functional operation a 1.7 Note 1 II 1% Note 1Either 2.1 Notes 1 and 2 1 ,5 % -m max. A4 Initial contact resistance a or 2.2 Notes 1 and 2 S3 as in

39、 2.3.6 NOTE See end of table 2. CECC 96 601:2002 - 10 -Table 1 Test schedule for quality conformance inspection, assessment level D Group B (non-destructive) (continued) To be conducted on a sampling basis, lot-by-lot Sub Test Measurement to be performed group Title a Conditions of test IL AQLTitle

40、Test detail Requirementso r See individual test methodsi a in 4.3 of EN 196000:1992 B1 Operating a 13.4 Note 1 S3 2,5 % Operating 13.4 Note 1 Note 1characteristics characteristicsIndexing mechanism i a 13.3 Note 1 Indexing mechanism 13.3 Note 1 Note 1Sealing Water proof i a 14.2 Note 1 Insulation re

41、sistance 3.1 Notes 1 and 2 -M min.(non-immersion) as in 2.3.5Water i a 14.3 Note 1 Visual examination 1.1 Note 1 No trace of water-M min.(immersion proof) Insulation resistance 3.1 Notes 1 and 2 as in 2.3.5Flux ingress i a 14.4 Notes 1 Note 1 Note 1 Note 1Visual examination 1.1 Note 1 No deteriorati

42、onImmersion in i a 15.1 Note 1 Insulation resistance 3.1 Notes 1 and 2 -M min.cleaning solvents as in 2.3.5 B2 Insulation resistance a 3.1 Notes 1 and 2 S3 1% Insulation resistance 3.1 Notes 1 and 2 -M min.as in 2.3.5Voltage a 4.1 Notes 1 and 2 Voltage proof 4.1 Notes 1 and 2 No breakdown or flashov

43、er NOTE See end of table 2. - 11 - CECC 96 601:2002Table 1 Test schedule for quality conformance inspection, assessment level D Group C (destructive) (continued) To be conducted on a periodic basis Sub Test Measurement to be performed group Title a Conditions of test p n c Title Test detail Requirem

44、entso r See individual test methodsi a in 4.3 of EN 196000:1992 C1 Robustness of a 8.3 Notes 1 and 2 6 5 1 Visual 1.1 Note 1 No damageterminations Solderability i a Either 12.1 Notes 1 and 2 Visual 1.1 Note 1 As in 12.1 or 12.2 o r 12.2 Notes 1 and 2 to be as appropriateDe-wetting i a 12.3 Notes 1 a

45、nd 2 Visual 1.1 Note 1 As in 12.3Resistance to i a Either 12.4 Notes 1 and 2 Visual 1.1 Note 1 No damageo r 12.5 Notes 1 and 2 to be Electrical overload a Either 10.1 Notes 1 and 2 only: Visual 1.1 Note 1 No damageseparate switches to be tested at: Contact resistance Either 2.1 -m max.Notes 1 and 2

46、as in 2.3.6or 2.2 Notes 1 and 2 to be specifiedFunctional 1.7 Note 1 As in 1.7(i) -V-mA d.c. Insulation 3.1 Notes 1 and 2 -M min.3 specimens as in 2.3.5(ii) -V-mA a.c. r.m.s. Voltage proof 4.1 Notes 1 and 2 No breakdown or 3 specimens flashovero r 10.1 and 10.2 Notes 1 and 2separate switches to be t

47、ested at:(i) -V-mA d.c. 2 specimens(ii) -V-mA a.c.r.m.s 2 (iii) Capacitive 2 specimens NOTES See end of table 2. CECC 96 601:2002 - 12 -Table 1 Test schedule for quality conformance inspection, assessment level D Group D (destructive) (continued) To be conducted on a periodic basis Sub Test Measurem

48、ent to be performed group Title a Conditions of test pncTitle Test detail Requirementso r See individual test methodsi a in 4.3 of EN 196000:1992 D1 Detailed dimensions a 1.5 Note 1 1 5 1 Detailed dimensions 1.5 Note 1 As in 1.5Robustness of a 8.1 Note 1 Visual examination 1.1 Note 1 No damageFunctional operation 1.7 Note 1 As in 1.7Sealing Water proof (i a) 14.2 Note 1(non-immersion)Insulation -M