CEA-2038-2012 Command朌riven Analog IR-Synchronized Active Eyewear.pdf

《CEA-2038-2012 Command朌riven Analog IR-Synchronized Active Eyewear.pdf》由会员分享，可在线阅读，更多相关《CEA-2038-2012 Command朌riven Analog IR-Synchronized Active Eyewear.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI/CEA Standard CommandDriven Analog IR-Synchronized Active Eyewear ANSI/CEA-2038 November 2012 NOTICE Consumer Electronics Association (CEA) Standards, Bulletins and other technical publications are designed to serve the public interest through eliminating misunderstandings between manufacturers

2、 and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards, Bulletins and other technical publications shall not in any respect preclud

3、e any member or nonmember of CEA from manufacturing or selling products not conforming to such Standards, Bulletins or other technical publications, nor shall the existence of such Standards, Bulletins and other technical publications preclude their voluntary use by those other than CEA members, whe

4、ther the standard is to be used either domestically or internationally. Standards, Bulletins and other technical publications are adopted by CEA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, CEA does not assume any liability to any patent owner, n

5、or does it assume any obligation whatever to parties adopting the Standard, Bulletin or other technical publication. This document does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this document

6、to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. This document is copyrighted by the Consumer Electronics Association (CEA) and may not be reproduced, in whole or part, without written permission. Federal copyright law

7、prohibits unauthorized reproduction of this document by any means. Organizations may obtain permission to reproduce a limited number of copies by entering into a license agreement. Requests to reproduce text, data, charts, figures or other material should be made to CEA. (Formulated under the cogniz

8、ance of the CEA R4 Video Systems Committee.) Published by CONSUMER ELECTRONICS ASSOCIATION 2012 Technology After1 (“A1”), Before1 (“B1”), After2 (“A2”), and Before2 (“B2”). The command sequence (order and repetition of commands) per image cycle define the mode of operation. The mode of operation spe

9、cified by the command sequence communicates information like Dual View versus 3D to the eyewear. The number of images per image cycle is specific to the mode of operation. The 3D Image Pairs shall come Left (odd image number) then Right (even image number) together in the Image Cycle. The operation

10、modes defined for the command set is summarized in the following table, a more detailed description of these modes can be found in Annex A of this document. Table 1: Operating Mode Summary Mode Number Mode Name Eyewear Support Description 1 Shutdown Required Both Shutters open 2 & 3 Symmetrical Sing

11、le 3D Required Single 3D image sent as 1st image to Left eye and 2nd image to Right eye. Variable shutter close timing. 4 Swap Single 3D Required Single 3D image sent as 1st image to Left eye and 2nd image to Right eye. Both shutters are never closed simultaneously. 5 & 6 Symmetrical Dual 2D3 Option

12、al4 Individual images are sent to the Left & Right eye. Variable shutter close timing. 7 Swap Dual 2D3 Optional4 Individual images are sent to the Left & Right eye. Both shutters are never closed simultaneously. 8 & 9 Single 2D Optional4 Image is sent to the Left & Right eye simultaneously. Variable

13、 shutter close timing. 10 Half Single 2D Optional4 Image is sent to the Left & Right eye simultaneously. Shutters are open 50% of the time. 11 & 12 Symmetrical Dual 3D2 Optional4 Two 3D images are sent as images 1&3 to the Left eye and images 2&4 to the Right eye Variable shutter close timing. 13 Sw

14、ap Dual 3D Optional4 Two 3D images are sent as images 1&3 to the Left eye and images 2&4 to the Right eye. Both shutters are never closed simultaneously. 14 & 15 Symmetrical Quad 2D Optional4 One of four individual images is sent to the Left & Right eye. Variable shutter close timing. 16 & 17 Asymme

15、trical Dual 2D 1 or Asymmetrical Single 3D Optional4 Individual 2D images sent to Left & Right eyes or single 3D image sent as 1st image to Left eye and 2nd image to Right eye. CEA-2038 6 1 Multiple 2D views or 3D view are selected on the eyewear and support is optional, however eyewear without sele

16、ction supporting such modes shall default to 3D. 2 Multiple 3D views are selected on the eyewear and support is optional, however eyewear without selection supporting such modes shall default to 3D with 1st and 2nd images. 3 Multiple 2D views are selected on the eyewear and support is optional, howe

17、ver eyewear without selection supporting such modes shall default to 2D with 1st image. 4 Unsupported modes shall be treated as the shutdown mode by the eyewear. 4.3.2 Command Timing a. The transmit time for each command shall be equal, the actual time depends on the short or long encoding selected.

18、 b. The actual transmit time shall be 305uS for short command encoding, and 1220uS for long command encoding. c. The time between a command and the associated shutter action for all symmetric modes shall be 1/16th of the command repetition period as measured at the center of the command. d. The time

19、 between a command and the associated shutter action for all asymmetric modes shall be equal to the command transmission time offset from the center of the command. e. The time between a command and any shutter action for all symmetric modes should be 1/16th of the command repetition period as measu

20、red at the center of the command. f. The time between a command and the any shutter action for all asymmetric modes should be equal to the command transmission time offset from the center of the command. g. The commands should be separated by at least one command transmission period. h. The lens tra

21、nsition from open to closed shall be when the transmittance is at or below 1%. i. The lens transition from closed to open shall be when the transmittance is at or above 1%. j. A swap transition of the lenses for 3D modes shall first close the previously open lens, and then open the previously closed

22、 lens if the actions cannot be simultaneous due to system design. The swap lens transition shall be complete when the closing lens transmittance is at or below 1% and the opening lens reaches a transmittance of 1%. k. Simultaneous lens transactions for 2D modes shall have the same lens transitioning

23、 first for opening and closing transitions to ensure more balanced timing between the lenses. Simultaneous lens transitions shall be complete when the last lens has transitioned to the 1% transmittance. See Annex A for detailed timing diagrams show valid and invalid cases. l. See detailed descriptio

24、n of operational modes in Annex A for implied lens open and close times. 4.3.3 Command Sequencing The following table summarizes the command sequences and resulting implied modes of operation. More detailed timing diagrams can be found in Annex A. CEA-2038 7 Table 2: Command Sequence Summary Operati

25、onal Mode Closed Duty Command Sequence Command Timing Dependence* Mode Number Eyewear Shutdown NA No Commands None 1 Symmetrical Single 3D Short A1, B1 Time(B1) Time(A1) Tperiod/2 2 Long B2, A2 Time(A2) Time(B2) Tperiod/2 3 Swap Single 3D None A1 None 4 Symmetrical Dual 2D Short A1, B1 Time(B1) Time

26、(A1) Tperiod/2 11 Long B2, A2, A2 Time(A2) Time(B2) Tperiod/2 12 Swap Dual 3D None B1 None 13 Symmetrical Quad 2D Short A1, B1, B1 Time(B1) Time(A1) Tperiod/2 Specific timing requirements Time B1(n) Time A1(n) + Tperiod/2 + 2*Tdelay Time B1(n) Tperiod/2 Specific timing requirements Time A2(n) Time B

27、2(n) + Tperiod/2 Time A2(n) Time A1(n) + 2*Tdelay Time B1(n) Tperiod/2 Specific timing requirements Time A2(n) Time B2(n) + Tdelay + 2*Tcommand Time A2(n) Time A1(n) + 2*Tdelay Time B2(n) Time B1(n) + 2*Tcommand Time A2(n) Time B1(n+1) 2*delay Command sequence, lens state and image timing circle L c

28、 l o s e d /R c l o s e dL o p e n /R o p e nT d e l a yB 1T p e r i o dD i s p l a y S h o w i n g I m a g e 1T c d u t yTclose-bothTdelayA2Topen-bothTperiod Time B1(n) Time B1(n-1) Tdelay Tperiod/16 Tcduty Time A2(n) Time B1(n) + 2*Tdelay Tclose-both Time B1(n) - Tdelay Topen-both Tclose-both + Tcduty Figure 12: Mode 9 Single 2D with Long Close Duty Timing