CAN CSA-E1029-2-1A-2006 Amendment 1 Safety of transportable motor-operated electric tools – Part 2-1 Particular requirements for circular saws.pdf

《CAN CSA-E1029-2-1A-2006 Amendment 1 Safety of transportable motor-operated electric tools – Part 2-1 Particular requirements for circular saws.pdf》由会员分享，可在线阅读，更多相关《CAN CSA-E1029-2-1A-2006 Amendment 1 Safety of transportable motor-operated electric tools – Part 2-1 Particular requirements for circular saws.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Amendment 1Safety of transportable motor-operatedelectric tools Part 2-1:Particular requirements for circular sawsAmendement 1Scurit des machines-outils lectriques semi-fixes Partie 2.1:Rgles particulires pour les scies circulairesPRICE CODE IEC 1999 Copyright - all rights reservedInternational Elec

2、trotechnical Commission 3, rue de Varemb Geneva, SwitzerlandTelefax: +41 22 919 0300 e-mail: inmailiec.ch IEC web site http:/www.iec.chCFor price, see current catalogueCommission Electrotechnique InternationaleInternational Electrotechnical CommissionAmendment 1:2006 toNational Standard of CanadaCAN

3、/CSA-E1029-2-1-94Amendment 1:1999 to International Standard CEI/IEC 1029-2-1:1993 has been adopted withoutmodification (IDT) as Amendment 1:2006 to CAN/CSA-E1029-2-1-94. At the time of publication, IECAmendment 1:1999 is available from IEC in English only. CSA will publish the French version when it

4、 becomesavailable from IEC. This Amendment was reviewed by the CSA Technical Committee on InternationalStandards, under the jurisdiction of the Strategic Steering Committee on Requirements for Electrical Safety, andhas been formally approved by the Technical Committee. April 2006 2 61029-2-1 Amend.

5、1 IEC:1999(E)FOREWORDThis amendment has been prepared by subcommittee 61F: Safety of hand-held motor-operatedelectric tools, of IEC technical committee 61: Safety of household and similar electricalappliances.The text of this amendment is based on the following documents:FDIS Report on voting61F/257

6、/FDIS 61F/263/RVDFull information on the voting for the approval of this amendment can be found in the report onvoting indicated in the above table.Page 72 DefinitionsSubclause 2.21Replace the third dashed item with the following: 0,13 s 0n for other saws designed for cutting depths from 20 mm to 55

7、 mm and forcircular saw components of combined machines;Add the following new fourth dashed item: 0,10 s 0n for other saws designed for cutting depths not exceeding 20 mm.Amendment 1:2006 to CAN/CSA-E1029-2-1-9461029-2-1 Amend. 1 IEC:1999(E) 3 Page 1318 Stability and mechanical hazardsSubclause 18.1

8、.104.1Replace, on page 17, the table of figure 102 by the following:Maximum diametersof saw bladeDimensionsof the saw table60 * 60 and 100 * 100 and 200 200L 175 300 5002D 5I 150 200 335 400a 87,5 150 2504D 5b 75 75 1109D 5* Maximum depth of cut: 15 mm.* Maximum depth of cut: 10 mm.Figure 102 Dimensions of the saw table in millimetresAmendment 1:2006 to CAN/CSA-E1029-2-1-94ICS 25.140.20