CAN CSA-C22 2 NO 60745-2-18A-2009 Amendment 1 Hand-held motor-operated electric tools - Safety - Part 2-18 Particular requirements for strapping tools (First Edition).pdf

《CAN CSA-C22 2 NO 60745-2-18A-2009 Amendment 1 Hand-held motor-operated electric tools - Safety - Part 2-18 Particular requirements for strapping tools (First Edition).pdf》由会员分享，可在线阅读，更多相关《CAN CSA-C22 2 NO 60745-2-18A-2009 Amendment 1 Hand-held motor-operated electric tools - Safety - Part 2-18 Particular requirements for strapping tools (First Edition).pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、(IEC 60745-2-18:2003, IDT)CAN/CSA-C22.2 No. 60745-2-18-05Amendment 1Hand-held motor-operated electric tools Safety Part 2-18: Particular requirements for strapping toolsAmendment 1:2009 (IDT) to National Standard of CanadaBlank pageCanadian Standards AssociationAmendment 1:2009 (IDT) to National Sta

2、ndard of CanadaCAN/CSA-C22.2 No. 60745-2-18-05, First Edition(IEC 60745-2-18:2003, IDT)Underwriters Laboratories Inc.UL 60745-2-18First EditionAmendment 1Hand-held motor-operated electric tools Safety Part 2-18:Particular requirements for strapping toolsAmendment publication date: MARCH 13, 2009This

3、 amendment is an adoption of IEC Amendment 1 (2008) to publication IEC 60745-2-18, First Edition (2003).ANSI/UL 60745-2-18-2009 2009Canadian Standards AssociationAll rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher.Am

4、endment 1:2008 to International Standard IEC 60745-2-18:2003 has been adopted without modification (IDT) as Amendment 1:2009 to CAN/CSA-C22.2 No. 60745-2-18-05. This Amendment was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA

5、 Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee.March 2009Copyright 2009 Underwriters Laboratories Inc.Revisions of this Standard will be made by iss

6、uing revised or additional pages bearing their date of issue. A UL Standard is current only if it incorporates the most recently adopted revisions, all of which are itemized on the transmittal notice that accompanies the latest set of revised requirements. Comments or proposals for revisions on any

7、part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/.The most recent designation of ANSI/UL 60745-2-18 as an American National Standard (ANSI) occurred on March 13, 200

8、9.This ANSI/UL Standard for Safety, which consists of the First edition with revisions through March 13, 2009, is under continuous maintenance, whereby each revision is ANSI approved upon publication.IEC 60745-2-18Edition 1.0 2008-02INTERNATIONAL STANDARD NORME INTERNATIONALEHand-held motor-operated

9、 electric tools Safety Part 2-18: Particular requirements for strapping tools Outils lectroportatifs moteur Scurit Partie 2-18: Rgles particulires pour les outils de cerclage INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE CICS 25.140.20 PRICE CODECODE PRIXAMENDM

10、ENT 1 AMENDEMENT 1 2 60745-2-18 Amend. 1 IEC:2008 FOREWORD This amendment has been prepared by subcommittee 61F: Safety of hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household and similar electrical appliances. The text of this amendment is based on the followi

11、ng documents: CDV Report on voting 61F/677/CDV 61F/725/RVC Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. With this amendment, this Part 2 is established on the basis of the fourth edition (2006) of IEC 60745-1, Ha

12、nd-held motor-operated electric tools Safety Part 1: General requirements. Main changes include editorial modifications to match with the fourth edition of IEC 60745-1 and clarifications in Annex K. The committee has decided that the contents of this amendment and the base publication will remain un

13、changed until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. _ 1 Scope Replace the existing text of Claus

14、e 1 by the following: This clause of Part 1 is applicable, except as follows: Addition: This standard applies to strapping tools. 3 Definitions Change the title of Clause 3 to read: 3 Terms and definitions Amendment 1:2009 to CAN/CSA-C22.2 No. 60745-2-18-0560745-2-18 Amend. 1 IEC:2008 3 20 Mechanica

15、l strength Replace the existing text of Clause 20 by the following: This clause of Part 1 is applicable, except as follows: 20.5 This subclause is not applicable. 21 Construction Replace the existing text of Clause 21 by the following: This clause of Part 1 is applicable, except as follows: 21.32 Th

16、is subclause is not applicable. Annexes Replace the existing texts of Annexes K and L by the following: Annex K (normative) Battery tools and battery packs K.1 Addition: All clauses of this Part 2 apply unless otherwise specified in this annex. K.12.2 This subclause of Part 2 is not applicable. K.12

17、.4 This subclause of Part 2 is not applicable. Annex L (normative) Battery tools and battery packs provided with mains connection or non-isolated sources L.1 Addition: All clauses of this Part 2 apply unless otherwise specified in this annex. _ Amendment 1:2009 to CAN/CSA-C22.2 No. 60745-2-18-05PRIN

18、TED IN CANADAIMPRIMEAU CANADA100%The Canadian Standards Association (CSA) prints its publications on Rolland Enviro100, which contains 100% recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactured using biogas energy.Copyright NoticeThis Amendment to the I

19、nternational Standard contains information copyright protected by theInternational Electrotechnical Commission (IEC). Except as permitted under the laws of Canada, no extract ofthis Amendment to the International Standard may be reproduced, stored in any retrieval system, ortransmitted in any form o

20、r by any means, electronic, photocopying, recording, or otherwise, without priorpermission from the Standards Council of Canada (SCC). Requests for permission to reproduce thisAmendment to the International Standard or parts thereof should be addressed to Manager, Technical Document Centre Standards

21、 Council of Canada 270 Albert Street, Suite 200 Ottawa, Ontario K1P 6N7 The Canadian adoption of this Amendment to the International Standard contains information copyrightprotected by the Canadian Standards Association. All rights reserved. No part of this adopted Amendmentmay be reproduced in any

22、form whatsoever without the prior permission of the publisher. IEC material isreprinted with permission. Requests for permission to reproduce this adopted Amendment or parts thereofshould be addressed to Director, Information Products Canadian Standards Association 5060 Spectrum Way, Suite 100 Mississauga, Ontario L4W 5N6 Copyright violators will be prosecuted to the full extent of the law.