BS ISO 2328-2011 Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions《叉车 钩接式叉臂和叉臂车厢 安装尺寸》.pdf

《BS ISO 2328-2011 Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions《叉车 钩接式叉臂和叉臂车厢 安装尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 2328-2011 Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions《叉车 钩接式叉臂和叉臂车厢 安装尺寸》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 2328:2011Fork-lift trucks Hook-on type fork arms and forkarm carriages MountingdimensionsBS ISO 2328:2011 BRITISH STANDARDNational forewordThis British Standard is the UK

2、implementation of ISO 2328:2011. Itsupersedes BS ISO 2328:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MHE/7, Industrial trucks.A list of organizations represented on this committee can beobtained on request to its secretary.This publication doe

3、s not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 65612 5ICS 53.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the

4、Standards Policy and Strategy Committee on 31 October 2011.Amendments issued since publicationDate Text affectedBS ISO 2328:2011Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensionsChariots lvateurs fourche Bras de fourche tenons et tabliers porte-fourches Dimensions de

5、montage ISO 2011Reference numberISO 2328:2011(E)Fourth edition2011-09-15ISO2328INTERNATIONAL STANDARDBS ISO 2328:2011ISO 2328:2011(E)COPYRIGHT PROTECTED DOCUMENT ISO 2011All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any m

6、eans, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrigh

7、tiso.orgWeb www.iso.orgPublished in Switzerlandii ISO 2011 All rights reservedBS ISO 2328:2011ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried

8、 out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO

9、 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International

10、 Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the element

11、s of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 2328 was prepared by Technical Committee ISO/TC 110, Industrial trucks, Subcommittee SC 2, Safety of powered industrial trucks.This fourth edition cancels and r

12、eplaces the third edition (ISO 2328:2007), which has been technically revised.ISO 2328:2011(E) ISO 2011 All rights reserved iiiBS ISO 2328:2011BS ISO 2328:2011INTERNATIONAL STANDARD ISO 2328:2011(E)Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions1 ScopeThis Internat

13、ional Standard specifies the dimensions of, and additional requirements for, fork carriers and hook-on type fork arms, to permit the interchangeability of these fork arms and/or other attachments, relative to the truck-rated capacity and fork arm type, on fork-lift trucks up to and including a rated

14、 capacity of 10 999 kg.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 2

15、331, Fork lift trucks Hook-on type fork arms VocabularyISO 3691-1, Industrial trucks Safety requirements and verification Part 1: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks3 Terms and definitionsFor the purposes of this document, t

16、he terms and definitions given in ISO 2331 and ISO 3691-1 apply.4 Requirements4.1 DimensionsThe mounting dimensions of the fork arms and fork carrier for type A (short drop) and type B (long drop) fork arms (the position of the lower hook determining the type of fork arm) shall be in accordance with

17、 Figures 1, 2 and 3 and Tables 1 and 2. The fork arm removal/mounting slot on the lower fork carrier is optional and shall be in accordance with 4.3. Fork arm location slots to the dimensions specified in Table 2 shall be provided at a suitable spacing on the fork carrier. In order to locate attachm

18、ents, one slot shall be situated on the top edge of the fork carrier centreline. However, when an offset lower slot is provided to avoid unintentional disengagement, then the lower slot shall be offset from the fork carrier centreline by dimension w (see Figure 1); this slot shall be 3 mm deeper tha

19、n k2(see Figure 3), to facilitate the attachment and fork arm mounting.4.2 StopsStops shall be provided in order to prevent lateral disengagement of the fork arms from the extremities of the fork carrier. If these stops are not permanent, i.e. welded, then the instruction handbook shall contain warn

20、ings that the truck is not to be used if the stops are not correctly in place.4.3 Slot on the lower carriageIf a fork arm removal/mounting slot is provided in the lower edge of the fork carrier, it shall be positioned as shown in Figure 3, that shown in the detailed view XX being optional. If the po

21、sitioning of the slots in the upper and lower fork carrier could enable the fork arm or attachment to become inadvertently disengaged from the carrier, then other means (e.g. mechanical) shall be provided to prevent this from occurring.Where the exclusive means of preventing unintentional fork arm d

22、isengagement is by an offset lower slot, then the instruction handbook shall contain the following warning notice: ISO 2011 All rights reserved 1BS ISO 2328:2011WARNING If the fork/locking pin is not fully engaged, the fork could become unintentionally disengaged.Key1 carriage centreline2 upper hook

23、3 fork carrier4 lower hookNOTE 1 For the values of the dimensions, see Tables 1 and 2.NOTE 2 h1and h2are fork arm dimensions; a and b are fork carrier dimensions.Figure 1 Hook -on type fork arm mounted on fork carrierISO 2328:2011(E)2 ISO 2011 All rights reservedBS ISO 2328:2011KeyX detail of upper

24、hookY detail of lower hookNOTE For the values of the dimensions, see Table 1.aUpper and lower fork hooks may be rounded or chamfered for clearance (see Table 1).bMaximum radius 1,0 mm.Figure 2 Fork arm hook detailISO 2328:2011(E) ISO 2011 All rights reserved 3BS ISO 2328:2011Key1 carriage centreline

25、2 slot on right side when looking at front face of the fork arm carrier3 hook-on type fork arm carrier 4 bottom of fork arm (ground level)5 lower hook of fork arm or attachment lug6a optional front slope for ease of attachment mounting6b optional front square cut-out for ease of attachment mountingN

26、OTE For the values of the dimensions, see Tables 1 and 2.aMaximum radius 5 mm.Figure 3 Hook-on type fork arm carrierISO 2328:2011(E)4 ISO 2011 All rights reservedBS ISO 2328:2011Table 1 Mounting dimensions of hook -on type fork armsDimensions in millimetresTruck rated capacity at rated distance of c

27、entre loadFork arm typea c1h1h2m1m2k1Lower hookvClass kg/mm ref.+100,3,0 tol. max. max. min. max.1Up to 999/ 400 and 600aA 7616,5394306+100,28 26 14 90B 114 43221 000 to 2 500/ 500 and 600bA 7616,5470382 31 29 14 90B 152 54632 501 to 4 999/ 500 and 600bA 7622568477+150,40 38 17 115B 203 69545 000 to

28、 8 000/ 600A 12726743598 47 45 20 139B 254 87058 001 to 10 999/ 600A 12735830680 65 63 26 164B 257 960a600 mm is used in the USA.b600 mm is used in the USA, Asia and Australia.Table 2 Mounting dimensions of fork carriersDimensions in millimetresTruck rated capacityat rated distance of centre loadFor

29、k arm typea b c2e h3k2qaLower slotuSlot offset from pClass kg/mm ref. ref.010 ,0,8 tol.015 ,min. 2,0 1,5 max.1Up to 999/ 400 and 600bA 76331 16 16 305010 ,13 8 95 13 160B 11421 000 to 2 500/ 500 and 600cA 76407 16 16 381 13 8 95 13 160B 15232 501 to 4 999/ 500 and 600cA 76508 21,5 19 476015 ,16 10 1

30、20 20 160B 20345 000 to 8 000/ 600A 127635 25,5 19 597 19 12 145 27,5 160B 25458 001 to 10 999/ 600A 127728 34 25 678 25 16 171 30 160B 257aThe centre slot shall be 3 mm deeper to facilitate attachment and fork arm mounting.b600 mm is used in the USA.c600 mm is used in the USA, Asia and Australia.IS

31、O 2328:2011(E) ISO 2011 All rights reserved 5BS ISO 2328:2011ISO 2328:2011(E)ICS 53.060Price based on 5 pages ISO 2011 All rights reservedThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, informa

32、tion and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996

33、Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity while

34、using this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers aut

35、omatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standar

36、ds publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Infor

37、mation on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and s

38、ervices. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996

39、 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications

40、 of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission

41、 from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: