BS ISO 23206-2006 Agricultural wheeled tractors and attachments - Front loaders - Carriages for attachments《农业轮式拖拉机和附件 前端式装载机 附件用托架》.pdf

《BS ISO 23206-2006 Agricultural wheeled tractors and attachments - Front loaders - Carriages for attachments《农业轮式拖拉机和附件 前端式装载机 附件用托架》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 23206-2006 Agricultural wheeled tractors and attachments - Front loaders - Carriages for attachments《农业轮式拖拉机和附件 前端式装载机 附件用托架》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 23206:2005 Incorporating corrigendum no. 1 Agricultural wheeled tractors and attachments Front loaders Carriages for attachments ICS 65.060.10 BS ISO 23206:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 13 Februa

2、ry 2006 BSI 2007 ISBN 0 580 47786 X National foreword This British Standard was published by BSI. It is the UK implementation of ISO 23206:2005, incorporating corrigendum March 2007. The UK participation in its preparation was entrusted to Technical Committee AGE/6, Agricultural tractors and forestr

3、y machinery. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer

4、 immunity from legal obligations. Amendments issued since publication Amd. No. Date Comments 17130 Corrigendum No. 1 31 May 2007 Replacement of Figure 3 Reference number ISO 23206:2005(E)INTERNATIONAL STANDARD ISO 23206 First edition 2005-06-01 Agricultural wheeled tractors and attachments Front loa

5、ders Carriages for attachments BS ISO 23206:2005ii BS ISO 23206:2005 iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO tech

6、nical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely

7、 with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft I

8、nternational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document

9、 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 23206 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 4, Tractors. blankBS ISO 23206:20051Agricultural wheele

10、d tractors and attachments Front loaders Carriages for attachments 1 Scope This International Standard specifies the dimensions and clearance requirements for the carriages for attachments on agricultural tractors and machines equipped with front loaders and having a maximum load capacity of 30 kN a

11、nd a maximum unladen tractor weight of 7 500 kg. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 front loader detachable unit consisting of lifting arms and fastening devices designed to be mounted on a frame on the front of a tractor and equ

12、ipped with a carriage for mounting various attachments See Figure 1. 2.2 attachment working device to be mounted on and operated with a front loader See Figure 1. Key 1 attachment 2 carriage 3 lifting arm Figure 1 Tractor with front loader and an attachment BS ISO 23206:2005 2 2.3 carriage coupler a

13、ssembly at the front loader arm end for mounting various attachments to the front loader See Figure 1. 2.4 maximum load capacity maximum vertical lift capacity generated at a point 800 mm horizontal in front of the locking pin of the carriage, when operating the lift and/or tilt cylinders See Figure

14、 2. Dimensions in millimetres Figure 2 Maximum load capacity 3 Dimensions and clearances The carriage dimensions and the dimensions associated with the attachment shall be in accordance with Figures 3 and 4. For the carriage clearance zones, see Figure 3. For the clearance at the back of the attachm

15、ent, see Figure 5. BS ISO 23206:2005 3Dimensions in millimetres Key 1 clearance for hook 2 clearance for eyelet 3 buffer for attachment 4 border of front of carriage 5 locking pin Figure 3 Carriage dimensions Explanation of the replacement of the figure For proper coupling/function of the carriage,

16、in the right-hand side of the drawing it is necessary that the horizontal dimension that was formerly W 35 mm, in combination with the dimension 720 0 2 mm, be in any case greater than the horizontal dimension 790 mm 2 mm in Figure 4. The sum of the smallest values allowed for dimensions W 35 mm (35

17、 mm itself) and 720 mm (718 mm) is 788 mm just the lower limit of dimension 790 mm 2 mm of Figure 4. In this case, no coupling is possible. Accordingly, horizontal dimension W 35 mm has been replaced by W 38 mm in the corrected Figure 3. BS ISO 23206:2005 4 Dimensions in millimetres Key 1 hook 2 eye

18、let 3 attachment buffer aaThe buffer shall be wide enough (W 790 mm) so that the attachment does not deform the carriage during normal operation. Figure 4 Dimensions associated with the attachment BS ISO 23206:2005 5Dimensions in millimetres Key 1 clearance Figure 5 Clearance at back of attachment B

19、S ISO 23206:2005 6 4 Requirements 4.1 General The front loader manufacturer shall specify the type and capacity of the allowable attachments that can be fitted and safely operated. 4.2 Locking device The locking pin on the carriage as shown in Figure 3 may be placed either inside or outside of the f

20、rame. 4.3 Locking and unlocking Locking and unlocking of the carriage to the attachment may be operated either from the drivers seat or from a place near the locking device. A means of visually verifying that the locking process is completed shall be provided such that it is visible from the positio

21、n where the locking device is operated. 4.4 Clearance zones Clearance zones 1 and 2 according to Figure 3 and the clearance at the back of the attachment as shown in Figure 5 shall be maintained to facilitate the coupling process. 4.5 Mounting height of eyelet to an attachment The recommended distan

22、ce between the base surface and the centre of the eyelet is W 150 mm. See Figure 6. Dimensions in millimetres Key 1 attachment 2 base surface Figure 6 Mounting height of eyelet to an attachment blankBS ISO 23206:2005 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is t

23、he independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure

24、that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsibl

25、e, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BS

26、I, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI polic

27、y to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.

28、Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and rece

29、ive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online ca

30、n be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the

31、Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing

32、 the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.