BS ISO 13296-2016 Diesel engines High-pressure fuel injection pipe assemblies General requirements and dimensions《柴油发动机 高压燃料喷射管组件 通用要求和尺寸规格》.pdf
《BS ISO 13296-2016 Diesel engines High-pressure fuel injection pipe assemblies General requirements and dimensions《柴油发动机 高压燃料喷射管组件 通用要求和尺寸规格》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 13296-2016 Diesel engines High-pressure fuel injection pipe assemblies General requirements and dimensions《柴油发动机 高压燃料喷射管组件 通用要求和尺寸规格》.pdf(20页珍藏版)》请在麦多课文档分享上搜索。
1、BS ISO 13296:2016Diesel engines High-pressurefuel injection pipe assemblies General requirements anddimensionsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 13296:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 1329
2、6:2016. It supersedes BS ISO 13296:2012 which is withdrawn. The UK participation in its preparation was entrusted to TechnicalCommittee MCE/22, Engines for road vehicles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport
3、 to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 91456 0ICS 43.060.40Compliance with a British Standard cannot confer immunity fromlegal obligations.T
4、his British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2016.Amendments/Corrigenda issued since publicationDate Text affectedBS ISO 13296:2016 ISO 2016Diesel engines High-pressure fuel injection pipe assemblies General requirements and dime
5、nsionsMoteurs diesels Lignes assembles dinjection de carburant haute pression Exigences gnrales et dimensionsINTERNATIONAL STANDARDISO13296Fourth edition2016-12-15Reference numberISO 13296:2016(E)BS ISO 13296:2016ISO 13296:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016,
6、Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Per
7、mission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 13296:2016ISO 13296:2016(E)Fo
8、reword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Dimensions and tolerances . 15 Cleanliness 36 Minimum bend radii . 37 Pipe end connections . 37.1 General . 37.2 Types of connection ends 37.3 Pipe end assembly for integral 60 female cones 47.4 Pipe end assembly for fabricated
9、 60 female cones . 67.5 Bore entrance configuration . 88 Assembly clamps 89 External coatings 910 Operating pressure 911 Pipe inside diameter 912 Tightening torque and sealing performance 913 Packaging and identification . 9Annex A (normative) Operating pressure 10Bibliography .11 ISO 2016 All right
10、s reserved iiiContents PageBS ISO 13296:2016ISO 13296:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical commit
11、tees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the In
12、ternational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the d
13、ifferent types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO s
14、hall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document
15、 is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Tech
16、nical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 34, Propulsion, powertrain, and powertrain fluids.This fourth edition cancels and replaces the third edition (ISO 13296:2012), w
17、hich has been technically revised by making normative reference to ISO 4288 for the measurement of surface texture.iv ISO 2016 All rights reservedBS ISO 13296:2016INTERNATIONAL STANDARD ISO 13296:2016(E)Diesel engines High-pressure fuel injection pipe assemblies General requirements and dimensions1
18、ScopeThis document specifies dimensions and requirements for high-pressure fuel injection pipe assemblies and assembled pipe sets for both integral and fabricated 60 female cones used on diesel (compression-ignition) engines.NOTE Dimensions of integral and fabricated 60 female cone connectors are sp
19、ecified in ISO 2974.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced
20、document (including any amendments) applies.ISO 2974:2011, Diesel engines 60 female cones for high-pressure fuel injection componentsISO 4288, Geometrical Product Specifications (GPS) Surface texture: Profile method Rules and procedures for the assessment of surface textureISO 8535-1:2011, Diesel en
21、gines Steel tubes for high-pressure fuel injection pipes Part 1: Requirements for seamless cold-drawn single-wall tubesISO 8535-2:2003, Compression-ignition engines Steel tubes for high-pressure fuel injection pipes Part 2: Requirements for composite tubesISO 12345, Diesel engines Cleanliness assess
22、ment of fuel injection equipment3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 7876-4 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org
23、/ ISO Online browsing platform: available at http:/www.iso.org/obp 4 Dimensions and tolerancesThe requirement and configuration drawing for a pipe assembly shall include at least the following:a) an indication of compliance with this document, i.e. ISO 13296;b) the outside diameter and inside diamet
24、er of the pipe and an indication of compliance with ISO 8535-1 or ISO 8535-2;c) the thread and the hexagon size of the connector nuts according to Table 2 or Table 4;d) the type of connection ends as specified in 7.2;e) a graphic representation of the centre-line of the pipe with the connection ends
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO132962016DIESELENGINESHIGHPRESSUREFUELINJECTIONPIPEASSEMBLIESGENERALREQUIREMENTSANDDIMENSIONS 柴油发动机

链接地址:http://www.mydoc123.com/p-584117.html