BS ISO 12822-2015 Glass packaging 26 H 126 crown finish Dimensions《玻璃包装 26 H 126冠形盖瓶口 尺寸》.pdf

《BS ISO 12822-2015 Glass packaging 26 H 126 crown finish Dimensions《玻璃包装 26 H 126冠形盖瓶口 尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 12822-2015 Glass packaging 26 H 126 crown finish Dimensions《玻璃包装 26 H 126冠形盖瓶口 尺寸》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 12822:2015Glass packaging 26 H 126crown finish DimensionsBS ISO 12822:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 12822:2015.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/7, Packagin

2、g - Glass.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published by BS

3、I StandardsLimited 2015ISBN 978 0 580 79195 6ICS 55.100Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2015.Amendments issued since publicationDate Text af

4、fectedBS ISO 12822:2015 ISO 2015Glass packaging 26 H 126 crown finish DimensionsEmballages en verre Bague couronne 26 H 126 DimensionsINTERNATIONAL STANDARDISO12822First edition2015-08-01Reference numberISO 12822:2015(E)BS ISO 12822:2015ISO 12822:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTE

5、CTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

6、 written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 12822

7、:2015ISO 12822:2015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Dimensions . 1Bibliography 5 ISO 2015 All rights reserved iiiContents PageBS ISO 12822:2015ISO 12822:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national stand

8、ards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International orga

9、nizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its

10、further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/dire

11、ctives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the

12、 Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related

13、 to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 63, Glass containers.iv ISO 2015 All rights reservedB

14、S ISO 12822:2015ISO 12822:2015(E)IntroductionThis International Standard is based on CE.T.I.E. (International Technical Centre for Bottling and Related Packaging) data sheet GME 13.02 Revision 1 (2007).Efficient packaging is of great importance for the distribution and the protection of goods. Insuf

15、ficient or inappropriate packaging can lead to damage or wastage of the contents of the pack.This International Standard is identical to EN 14635:2010. ISO 2015 All rights reserved vBS ISO 12822:2015BS ISO 12822:2015Glass packaging 26 H 126 crown finish Dimensions1 ScopeThis International standard s

16、pecifies the dimensions of the 26 mm shallow crown finish for glass bottles containing beverages. The shallow crown finish is designed to use a metal crown closure (see CE.T.I.E. data sheet EC1-02 revision 1).2 Normative referencesThe following documents, in whole or in part, are normatively referen

17、ced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 9058, Glass containers Standard tolerances for bottles3 DimensionsThe des

18、ign and dimensions of the finish shall be as shown in Figure 1 to Figure 5.Details which are not specified shall be selected in accordance with the application.For general tolerances, ISO 9058 shall apply.Dimensions in millimetresg389Keya between 18,5 max and 17 min measured at 3 mm max down from th

19、e top.Figure 1 Shoulder and bore dimensionsConstruction limit: Certain capping equipment may place further dimensional limits on the neck contour.INTERNATIONAL STANDARD ISO 12822:2015(E) ISO 2015 All rights reserved 1BS ISO 12822:2015ISO 12822:2015(E)Dimensions in millimetresg389g390g391KeyaNominal

20、diameter to suit glass manufacturer.bDetail X (see Figure 4 and Figure 5).cTop of the finish.Figure 2 Profile of the finish2 ISO 2015 All rights reservedBS ISO 12822:2015ISO 12822:2015(E)Dimensions in millimetresg389KeyaFor optimum performance, the radius should lie between 0,5 and 0,8 excluding the

21、 vertical mould joint and be as near as possible to 0,5.Figure 3 Point “P”Dimensions in millimetresg389g389g390g391KeyaMould parting line of glass finish.bFlat.cGlass sealing surface.Figure 4 Detail X Glass sealing surface Alternative 1 ISO 2015 All rights reserved 3BS ISO 12822:2015ISO 12822:2015(E

22、)Contact between the crown cork liner compound and the internal mould parting line of glass finish should be avoided (see CE.T.I.E. data sheets EC1-02 revision 1 and EC1-021). The sealing surface should be smooth and free of any defects.Dimensions in millimetresg389g389g391g390KeyaMould parting line

23、 of glass finish.bFlat.cGlass sealing surface.Figure 5 Detail X Glass sealing surface Alternative 2Contact between the crown cork liner compound and the internal mould parting line of glass finish should be avoided (see CE.T.I.E. data sheets EC1-02 revision 1 and EC1-021). The sealing surface should

24、 be smooth and free of any defects.4 ISO 2015 All rights reservedBS ISO 12822:2015ISO 12822:2015(E)Bibliography1 ISO 9058, Glass containers Standard tolerances for bottles2 CE.T.I.E. data sheet GME 13.02 Revision 1, 26 H 126 Crown finish1)3 CE.T.I.E. EC1-02 revision 1, 26 millimetres crown cork4 CE.

25、T.I.E. EC1-021, 26 millimetres crown cork: main liner profiles1) Obtainable through Centre Technique International de lEmbouteillage (CE.T.I.E), 112-114, rue La Botie, 75008 Paris, France: www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21. ISO 2015 All rights reserved 5BS ISO 12822:2015I

26、SO 12822:2015(E) ISO 2015 All rights reservedICS 55.100Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standard

27、s and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience an

28、d expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information o

29、n standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, includin

30、g British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur ran

31、ge of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its availa

32、ble 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclus

33、ive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host stand

34、ards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment

35、 or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all Britis

36、h Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as p

37、ermitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Cop

38、yright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW