BS ISO 12576-2-2008 Thermal insulation products - Conformity control systems - In-situ products《绝热产品 一致性控制系统 现场制品》.pdf

《BS ISO 12576-2-2008 Thermal insulation products - Conformity control systems - In-situ products《绝热产品 一致性控制系统 现场制品》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 12576-2-2008 Thermal insulation products - Conformity control systems - In-situ products《绝热产品 一致性控制系统 现场制品》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO12576-2:2008ICS 91.100.60NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDThermal insulationproducts Conformitycontrol systemsPart 2: In-situ productsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 32008

2、 BSI 2008ISBN 978 0 580 58543 2Amendments/corrigenda issued since publicationDate CommentsBS ISO 12576-2:2008National forewordThis British Standard is the UK implementation of ISO 12576-2:2008.The UK participation in its preparation was entrusted to TechnicalCommittee B/540/8, Mirror committee for I

3、SO/TC 163.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immuni

4、tyfrom legal obligations.0 SeptemberBS ISO 12576-2:2008Reference numberISO 12576-2:2008(E)ISO 2008INTERNATIONAL STANDARD ISO12576-2First edition2008-07-01Thermal insulation products Conformity control systems Part 2: In-situ products Produits isolants thermiques Systmes de contrle de la conformit Pa

5、rtie 2: Produits fabriqus sur place BS ISO 12576-2:2008ISO 12576-2:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and i

6、nstalled on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software p

7、roducts used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is foun

8、d, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and micr

9、ofilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2

10、008 All rights reservedBS ISO 12576-2:2008ISO 12576-2:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv 1 Scope 1 2 Normative references 1 3 Terms and definitions .2 4 Conformity systems, their elements and recommended application of the systems3 5 Factory production control.6 6 Site

11、 installation control .6 7 Certification of factory production control and of site quality control 8 8 Sampling.12 Bibliography 13 BS ISO 12576-2:2008ISO 12576-2:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of nati

12、onal standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internat

13、ional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the ru

14、les given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at

15、 least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12576-2 was prepared by Technical Committee ISO/

16、TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 3, Thermal insulation products. ISO 12576 consists of the following parts, under the general title Thermal insulation products Conformity control systems: Part 1: Factory-made products Part 2: In-situ products BS IS

17、O 12576-2:2008INTERNATIONAL STANDARD ISO 12576-2:2008(E) ISO 2008 All rights reserved 1Thermal insulation products Conformity control systems Part 2: In-situ products 1 Scope This part of ISO 12576 establishes three systems for the conformity control of thermal insulation products that are manufactu

18、red on site from components produced in a factory, and provides the minimum requirements for each system. Examples of these types of products are loose fill and spray-applied insulations. The purpose of this part of ISO 12576 is to provide uniform methods to determine whether the production of a the

19、rmal insulation product is acceptable as conforming to the relevant specification requirements once it is installed on site. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For und

20、ated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC Guide 65, General requirements for bodies operating product certification systems ISO 9229, Thermal insulation Vocabulary ISO 12576-1, Thermal insulation Insulating materials and products for b

21、uildings Conformity control systems Part 1: Factory-made products ISO 17020, General criteria for the operation of various types of bodies performing inspection ISO 17021, Conformity assessment Requirements for bodies providing audit and certification of management systems ISO 17024, Conformity asse

22、ssment General requirements for bodies operating certification of persons ISO 17025, General requirements for the competence of testing and calibration laboratories ISO 17050-1, Conformity assessment Suppliers declaration of conformity Part 1: General requirements BS ISO 12576-2:2008ISO 12576-2:2008

23、(E) 2 ISO 2008 All rights reserved3 Terms and definitions For the purpose of this document, the terms and definitions given in ISO 9229 and the following apply. 3.1 certification organization organization that conducts certification of conformity and is accredited by an appropriate body, possessing

24、the necessary competence and reliability to operate a certification system in accordance with International Standards in which the interests of all parties concerned with the functioning of the system are represented NOTE A certification organization may operate its own testing and inspection activi

25、ties or oversee these activities carried out on its behalf by other bodies. 3.2 conformity control performance of control methods to prove whether a product can be accepted as conforming to specified requirements 3.3 inspection lot definite quantity of packages (product items) manufactured under con

26、ditions that are presumed uniform, and that are submitted for inspection and accepted or rejected as a whole, depending on the quality found by inspection of a representative sample drawn from the lot 3.4 manufacturers declaration of conformity action by which a manufacturer declares under his own r

27、esponsibility, by means of a “declaration of conformity” that the product is in conformity with the specification, without being under procedures of a third-party certification system See ISO 17050-1. 3.5 qualified contractor individual, organization or corporation who/that has the knowledge require

28、d for installing the material, who/that is responsible for the installation of the material and who/that has the contractual obligations for the installation 3.6 qualified installer individual who has proper knowledge of the installation requirements and who installs the material on site to form the

29、 final product 3.7 specification document defining requirements for performance of the product 3.8 third party person or body that is recognized as being independent of the parties involved with respect to the issues in question 3.9 third-party certification certification provided by a person or bod

30、y that is recognized as being independent of the parties involved the certification See ISO 17000. 3.10 verification validation by a third party, independent of the manufacturer, of the manufacturers declaration of conformity BS ISO 12576-2:2008ISO 12576-2:2008(E) ISO 2008 All rights reserved 34 Con

31、formity systems, their elements and recommended application of the systems 4.1 General In this specification, the following three systems for attestation of conformity are described: system A: qualified contractors self-declaration of conformity in accordance with ISO 17050-1, based on the installer

32、s documented installation procedures and internal quality control and initial type testing of the product by the manufacturer, without any participation of a third party to the ongoing surveillance of factory production or site installation; system B: qualified contractors declaration of conformity,

33、 based on the installers documented installation procedures and internal quality control and initial type testing of the components by a laboratory accredited in accordance with ISO 17025, where both the manufacturers quality control and the installers quality control has been certified initially by

34、 a third party; there is ongoing surveillance for the factory production control but not for the site installation; system C: installed product certification by a certification organization in accordance with ISO 17021 and ISO/IEC Guide 65, based on the installers documented installation procedures

35、and internal quality control and initial type testing of the components by a laboratory accredited in accordance with ISO 17025, where both the manufacturers quality control and the installers quality control has been certified initially by a third party; the certification organization certifies the

36、 installer in accordance with ISO 17024 and ongoing surveillance site audits are conducted on a regular basis by the certification organization accredited in accordance with ISO 17020. NOTE Systems B and C have a progressive increase in third-party involvement in the conformity control system. 4.2 S

37、ystem A Declaration of conformity by a qualified contractor Initial type testing of manufacturers product, manufacturers internal quality control and qualified contractors internal site quality control This system is based on the following elements: a) manufacturers responsibilities: factory product

38、ion control; having initial type testing of the components completed by the manufacturer; b) qualified contractors responsibilities: self-declaration of conformity following requirements outlined in ISO 17050-1; document site quality-control programme; c) qualified installers responsibilities: docum

39、ented installation procedures; ongoing site inspection and testing by the installer; daily work records by the installer; d) certification organization: none. BS ISO 12576-2:2008ISO 12576-2:2008(E) 4 ISO 2008 All rights reservedBy the qualified contractors declaration of conformity, the contractor v

40、erifies that the installation is under a site quality-control program and that the results of the site quality-control program show that the installed products are in conformity with the product specification and any applicable installation standards. 4.3 System B Declaration of conformity by an ins

41、taller Initial type testing of manufacturers product by a third party, third-party verification of factory production control, verification of a qualified contractors site quality-control program and site quality control by a qualified contractor This system is based on the following elements: a) ma

42、nufacturers responsibilities: factory production control; having initial type testing of the components completed by a laboratory accredited in accordance with ISO 17025; b) qualified contractors responsibilities: document site quality-control program; c) qualified installers responsibilities: docum

43、ented installation procedures; ongoing site inspection and testing by the installer; daily work records by the installer; d) certification organization, in accordance with ISO 17021 and ISO/IEC Guide 65: testing laboratory accredited in accordance with ISO 17025; initial inspection of factory produc

44、tion control; ongoing surveillance audits of factory production control; initial inspection of the qualified contractors installation procedures, site quality-control program, installers site inspection, installers site testing procedures and daily work record. By the qualified contractors declarati

45、on of conformity, the qualified contractor verifies that the installation is under a site quality-control program that has been verified by a third party and that the results of the site quality-control program show that the installed product is in conformity with the product specification and any i

46、nstallation standards. The qualified contractor also declares that the factory production control has been verified and is being monitored by a certification organization. Certification bodies shall be in accordance with ISO 17021 and be accredited by an accreditation body that is member of the IAF/

47、ILAC Multilateral Agreement. BS ISO 12576-2:2008ISO 12576-2:2008(E) ISO 2008 All rights reserved 54.4 System C Declaration of conformity by a third party Initial type testing of manufacturers product by a third party, third-party verification of factory production control, verification of a qualifie

48、d contractors site quality-control program and site quality control by a third party This system is based on the following elements: a) manufacturers responsibilities: factory production control; initial type testing of the components completed by a laboratory accredited in accordance with ISO 17025

49、; b) qualified contractors responsibilities: document site quality-control program; c) qualified installers responsibilities: documented installation procedures; ongoing site inspection and testing by the installer; daily work records by the installer; d) certification organization, in accordance ISO 17021 and ISO/IEC Guide 65: testing laboratory accredited in accordance with ISO 17025; initial inspection of fac