BS ISO 11527-2010 Building construction Sealants Test method for the determination of stringiness《房屋建筑 密封剂 粘性测定用试验方法》.pdf

《BS ISO 11527-2010 Building construction Sealants Test method for the determination of stringiness《房屋建筑 密封剂 粘性测定用试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 11527-2010 Building construction Sealants Test method for the determination of stringiness《房屋建筑 密封剂 粘性测定用试验方法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 11527:2010Building construction Sealants Test method for thedetermination of stringinessBS ISO 11527:2010 BRITISH STANDARDNational forewordThis British Standard is the UK

2、implementation of ISO 11527:2010.The UK participation in its preparation was entrusted to TechnicalCommittee B/547, Sealants for building and construction.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all

3、 the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 65514 2ICS 91.100.50Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Stra

4、tegy Committee on 30 November 2010.Amendments issued since publicationDate Text affectedBS ISO 11527:2010Reference numberISO 11527:2010(E)ISO 2010INTERNATIONAL STANDARD ISO11527First edition2010-11-15Building construction Sealants Test method for the determination of stringiness Construction immobil

5、ire Mastics Mthode dessai pour la dtermination du pouvoir filant BS ISO 11527:2010ISO 11527:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embed

6、ded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated.

7、Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a probl

8、em relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includ

9、ing photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publishe

10、d in Switzerland ii ISO 2010 All rights reservedBS ISO 11527:2010ISO 11527:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standar

11、ds is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take

12、 part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is

13、to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility

14、 that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11527 was prepared by Technical Committee ISO/TC 59, Buildings and civil engineering works, Subcommittee SC 8, Sealants. BS ISO 11527:

15、2010BS ISO 11527:2010INTERNATIONAL STANDARD ISO 11527:2010(E) ISO 2010 All rights reserved 1Building construction Sealants Test method for the determination of stringiness 1 Scope This International Standard specifies a method for the determination of the stringiness of a wet-applied sealant. 2 Norm

16、ative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6927, Building construction

17、Jointing products Vocabulary for sealants1)3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6927 apply. 4 Principle This method determines the stringiness of a sealant by measuring the maximum length of a strand or string which can be pulled from a we

18、t sealant sample. A probe (tip) is forced into the wet sealant sample. After a short time, the probe is removed from the sample using a constant rate of pull. An extensometer or similar apparatus is used to provide a constant rate of pull, and the maximum travel before the “string” breaks is reporte

19、d in millimetres. 5 Apparatus 5.1 Extensometer or similar apparatus Extensometer or other apparatus, e.g. pneumatic piston, which allows a grip to be pulled at a constant rate and provides a reading of the distance between the grips to the nearest millimetre. 5.2 Probe Tip 1 (round) according to Fig

20、ure 1. Tip 2 (conical) according to Figure 2. Tip made of aluminium. 1) Under revision. BS ISO 11527:2010ISO 11527:2010(E) 2 ISO 2010 All rights reservedDimensions in millimetres Figure 1 Tip 1 Dimensions in millimetres Figure 2 Tip 2 5.3 Container Container from any suitable source, with a minimum

21、depth of 30 mm and a minimum diameter of 30 mm. 6 Conditioning The sealant shall be shelf-aged for a minimum of 1 d from production. Prior to preparation of the specimen, the sealant, the container and the probe (tip) shall be conditioned for 6 h in the unopened container at the test temperature, e.

22、g. (23 2) C. 7 Preparation of test specimens Fill the container with the sample and remove excess with a spatula to provide a clean, smooth surface free of bubbles. 8 Test procedure Attach the probe (tip) to the upper clamp of the extension device (e.g. the extensometer). Fix the container to the lo

23、wer clamp of the extension device. Slowly raise the container with the wet sealant or move the probe downwards until the nozzle just touches the sample surface. This is the “zero” reading. Alternatively, the “zero” reading can be determined by placing a sheet of paper on the container (assuming the

24、sealant is tooled evenly with the upper edges of the container). Raise the container with the wet sealant further or move the tip downwards at a rate of 60 mm/min until the tip of the nozzle is submerged a minimum of 10 mm into the sample. Begin the test by moving either the probe upwards or the con

25、tainer with the sealant sample downwards at a rate of 700 mm/min. Stop the extension machine when the string formed between the sealant in the container and the tip breaks and report the length of the string at break (Lmax). Do not clean the tip. BS ISO 11527:2010ISO 11527:2010(E) ISO 2010 All right

26、s reserved 3Repeat the test two more times (it is not necessary to smooth the surface and to clean the tip between tests). Then take another specimen (container with wet sealant) and repeat the test (making three new measurements), i.e. generate six measurements in total. NOTE For slow-curing sealan

27、ts, sequential measurements can be carried out on the same sealant specimen. 9 Expression of results Report the individual readings and the average over the second, third, and fourth trials to the nearest millimetre. The repeatability of the value reported (the maximum difference between two indepen

28、dent results) should not exceed 4 mm at the 95 % confidence level. If the sample surface cures before measurements are complete, results will be in error. If either the highest or lowest of the three measurements is greater than 15 % from the median, discard the data and repeat the test from the ini

29、tial preparation. 10 Test report The test report shall include at least the following information: a) name of test laboratory, number and date of test report; b) reference to this International Standard; c) name, type (chemical family) and colour of sealant; d) batch of sealant from which the test s

30、pecimens were produced, if possible; e) test temperature; f) individual and average measurement values for stringiness; g) any deviations from the specified test conditions. BS ISO 11527:2010ISO 11527:2010(E) ICS 91.100.50 Price based on 3 pages ISO 2010 All rights reserved This page deliberately le

31、ft blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution

32、 (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant

33、 aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +4

34、4 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions

35、of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards,

36、 it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004

37、Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial dis

38、counts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI

39、is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a ret

40、rieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: