BS EN ISO 11432-2005 Building construction - Sealants - Determination of resistance to compression《房屋建筑 密封胶 抗压性测定》.pdf

《BS EN ISO 11432-2005 Building construction - Sealants - Determination of resistance to compression《房屋建筑 密封胶 抗压性测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 11432-2005 Building construction - Sealants - Determination of resistance to compression《房屋建筑 密封胶 抗压性测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Determination of resistance to compressionThe European Standard EN ISO 11432:2005 has the status of

2、 a British StandardICS 91.100.50Building construction Sealants BRITISH STANDARDBS EN ISO 11432:2005BS EN ISO 11432:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 17 November 2005 BSI 17 November 2005ISBN 0 580 46763 5Additional informati

3、onEN ISO 11432:2005 is a test method useful in the determination of compressive properties and one of the procedures used for classifying construction sealants within BS EN ISO 11600:2003.Cross-referencesThe British Standards which implement international or European publications referred to in this

4、 document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contr

5、act. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, page

6、s ii to iv, pages 1 to 5 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsA list of organizations represented on this committee can be obtained on request to its secretary. presen

7、t to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.National forewordThis British Standard is the official English lan

8、guage version of EN ISO 11432:2005. It is identical with ISO 11432:2005. It supersedes BS EN ISO 11432:1998 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/547, Sealants for building and construction, which has the responsibility to: aid enquirers to

9、 understand the text;EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 11432July 2005ICS 91.100.50 Supersedes EN ISO 11432:1997 English VersionBuilding construction - Sealants - Determination of resistance tocompression (ISO 11432:2005)Construction immobilire - Mastics - Dtermination de larsista

10、nce la compression des mastics (ISO 11432:2005)Hochbau - Fugendichtstoffe - Bestimmung desDruckwiderstands (ISO 11432:2005)This European Standard was approved by CEN on 20 June 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving th

11、is EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (Eng

12、lish, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czec

13、h Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMAL

14、ISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 11432:2005: EForeword This document (EN ISO 11432:2005) has been prepared by Technic

15、al Committee ISO/TC 59 “Building construction“ in collaboration with CMC. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2006, and conflicting national standards shall be withdrawn at the

16、 latest by January 2006. This document supersedes EN ISO 11432:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland,

17、France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of ISO 11432:2005 has been approved by CEN as EN ISO 11432:2005 witho

18、ut any modifications. EN ISO 11432:2005Reference numberISO 11432:2005(E)INTERNATIONAL STANDARD ISO11432Second edition2005-07-01Building construction Sealants Determination of resistance to compression Construction immobilire Mastics Dtermination de la rsistance la compression des mastics EN ISO 1143

19、2:2005ii iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 1 4 Principle. 1 5 Apparatus 1 6 Preparation of test specimens 2 7 Conditioning of test specimens 2 8 Test procedure 3 9 Expression of results . 3 10 Test report . 3 EN ISO 11432:2005iv Foreword ISO

20、 (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical com

21、mittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrot

22、echnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the mem

23、ber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identify

24、ing any or all such patent rights. ISO 11432 was prepared by Technical Committee ISO/TC 59, Building construction, Subcommittee SC 8, Jointing products. This second edition cancels and replaces the first edition (ISO 11432:1993), Clauses 5, 6 and 7 of which have been technically revised. EN ISO 1143

25、2:20051Building construction Sealants Determination of resistance to compression 1 Scope This International Standard specifies a method for the determination of the resistance to compression of sealants used in joints in building construction. 2 Normative references The following referenced document

26、s are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6927, Building construction Jointing products Sealants Vocabulary ISO 13640, B

27、uilding construction Jointing products Specifications for test substrates 3 Terms and definitions For the purposes of this document, the definitions given in ISO 6927 apply. 4 Principle Test specimens, in which the sealant to be tested is adhered to two parallel substrate surfaces, are compressed by

28、 a defined percentage of the original width and the force recorded. 5 Apparatus 5.1 Substrate materials, used for the preparation of test specimens, are defined in ISO 13640, Specification for test substrates. The materials shall be selected from mortar and/or anodized aluminium and/or glass. Other

29、substrate materials may be used as agreed by the parties concerned. For each test specimen, two substrate pieces of the same material are required; with dimensions as shown in Figures 1 and 2. Test substrates of other dimensions may be used, but then the dimensions of the sealant bead and the area o

30、f adhesion shall be the same as those shown in Figures 1 and 2. 5.2 Spacers, for the preparation of the test specimens, of cross-sections (12 mm 12 mm) with anti-adherent surface. 5.3 Anti-adherent substrate, for the preparation of test specimens, e.g. polyethylene (PE) film, preferably according to

31、 the advice of the sealant manufacturer. 5.4 Ventilated convection-type oven, capable of operating at (70 2) C for conditioning according to method B. 5.5 Container, for water immersion of the specimen for conditioning according to method B. 5.6 Tensile test machine, capable of compressing the test

32、specimens at a rate of (5,5 0,7) mm/min. EN ISO 11432:20052 6 Preparation of test specimens The sealant and the test substrate shall be brought to (23 2) C. For each substrate material, three test specimens shall be prepared. For each test specimen, two substrates (5.1) and two spacers (5.2) shall b

33、e assembled (see Figures 1 and 2) and set on the anti-adherent substrate (5.3). The instructions of the sealant manufacturer shall be followed concerning, for instance, whether a primer is to be used and the mixing procedure for multi-component sealants. The hollow volume formed by the substrates sh

34、all be filled with the sealant. The following precautions shall be taken: a) the formation of air bubbles shall be avoided; b) the sealant shall be pressed to the contact surfaces of the substrates; c) the sealant surface shall be trimmed so that it is flush with the faces of the substrates and the

35、spacers. The test specimens shall be set on the edge of one of the supports and the anti-adherent substrate shall be removed as soon as possible. The test specimens shall be kept in this position to allow curing or optimum drying of the sealant. The spacers shall be maintained in place during condit

36、ioning. 7 Conditioning of test specimens 7.1 General The test specimens shall be conditioned either according to method A (see 7.2) or method B (see 7.3). 7.2 Conditioning method A The test specimens shall be conditioned for 28 days at (23 2) C and (50 5) % relative humidity. 7.3 Conditioning method

37、 B First the test specimens shall be conditioned according to method A and subsequently subjected three times to the following storage cycle: a) three days in the oven (5.4) at (70 2) C; b) one day in distilled water (5.5) at (23 2) C; c) two days in the oven (5.4) at (70 2) C; d) one day in distill

38、ed water (5.5) at (23 2) C. This cycle may be carried out alternatively in the sequence: c), d), a), b). After conditioning according to method B, the test specimens shall be stored for a further period of 24 h at (23 2) C and (50 5) % relative humidity before testing. NOTE Conditioning method B is

39、a normal conditioning procedure using the influence of heat and water. It is not intended to give information on the durability of the sealant. EN ISO 11432:200538 Test procedure The test shall be carried out at (23 2) C and (50 5) % relative humidity. The spacers (5.2) shall be removed. The test sp

40、ecimens shall be placed in the tensile test machine (5.6) and compressed at a rate of (5,5 0,7) mm/min to 75 % or 80 % of the initial width, or by any other percentage as agreed by the parties concerned. The following table gives the correspondence in millimetres of the percentage compression for a

41、test specimen of 12 mm initial width. Table 1 Correspondence of compression values original width 12 mm Compressed width relative to the original width % Compression % Width after compression mm 75 25 9,0 80 20 9,6 The force, expressed in newtons, required for the appropriate compression shall be re

42、corded. 9 Expression of results For each test specimen, the secant compression modulus shall be calculated, for the chosen compression amplitude, rounded to 0,01 N/mm2, using the equation: Secant compression modulus = Force at chosen compression (expressed in N)/initial cross-section area (expressed

43、 in mm2) The arithmetic mean of the three secant compression modulus values shall be calculated, rounded to 0,01 N/mm2. 10 Test report The test report shall contain the following information: a) the test laboratorys name and the date of testing; b) a reference to this International Standard; c) name

44、, type (chemical family) and colour of sealant; d) batch of sealant from which the test specimens were produced; e) substrate material used; f) the primer used, if applicable; g) the method of conditioning (see Clause 7); h) the percentage compression (see Clause 8); i) the secant compression modulu

45、s of each test specimen (N/mm2); j) the arithmetic mean of the three secant compression moduls; k) any deviations from this International Standard. EN ISO 11432:20054 Dimensions in millimetres Key 1 mortar substrates 2 sealant 3 spacers (5.2) Figure 1 Test specimens with mortar substrates EN ISO 114

46、32:20055Dimensions in millimetres Key 1 anodized aluminium or glass substrates 2 sealant 3 spacers (5.2) Figure 2 Test specimens with anodized aluminium or glass substrates EN ISO 11432:2005BS EN ISO BSI389 Chiswick High RoadLondonW4 4AL11432:2005BSI British Standards InstitutionBSI is the independe

47、nt national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they poss

48、ess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity

49、 of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Stand