BS EN ISO 4895-2014 Plastics Liquid epoxy resins Determination of tendency to crystallize《塑料 液态环氧树脂 结晶倾向的测定》.pdf

《BS EN ISO 4895-2014 Plastics Liquid epoxy resins Determination of tendency to crystallize《塑料 液态环氧树脂 结晶倾向的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 4895-2014 Plastics Liquid epoxy resins Determination of tendency to crystallize《塑料 液态环氧树脂 结晶倾向的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 4895:2014Plastics Liquid epoxy resins Determination of tendencyto crystallizeBS EN ISO 4895:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 4895:2014.It supersedes BS EN ISO 4895:1999 which is withdrawn.The UK particip

2、ation in its preparation was entrusted to TechnicalCommittee PRI/42, Fibre reinforced thermosetting plastics andprepregs.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a cont

3、ract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 81809 7ICS 83.080.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho

4、rity of theStandards Policy and Strategy Committee on 31 July 2014.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4895 July 2014 ICS 83.080.10 Supersedes EN ISO 4895:1999English Version Plastics - Liquid epoxy resins - Determination of t

5、endency to crystallize (ISO 4895:2014) Plastiques - Rsines poxydes liquides - Dtermination de la tendance la cristallisation (ISO 4895:2014) Kunststoffe - Flssige Epoxidharze - Bestimmung der Kristallisationsneigung (ISO 4895:2014) This European Standard was approved by CEN on 28 June 2014. CEN memb

6、ers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicati

7、on to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Managem

8、ent Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

9、Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 1

10、7, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4895:2014 EBS EN ISO 4895:2014EN ISO 4895:2014 (E) 3 Foreword This document (EN ISO 4895:2014) has been prepared by Technical Committee ISO/TC 61 “Plastics

11、“ in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2015, and conflicting national st

12、andards shall be withdrawn at the latest by January 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN

13、ISO 4895:1999. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedon

14、ia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 4895:2014 has been approved by CEN as

15、 EN ISO 4895:2014 without any modification. BS EN ISO 4895:2014ISO 4895:2014(E) ISO 2014 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope . 12 Normative references 13 Principle 14 Reagents 15 Apparatus . 16 Procedure. 27 Expression of results 38 Precision . 39 Test report . 3BS E

16、N ISO 4895:2014ISO 4895:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interes

17、ted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical C

18、ommission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO document

19、s should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible f

20、or identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the

21、convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Fore

22、word - Supplementary informationThe committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 12, Thermosetting materials.This third edition cancels and replaces the second edition (ISO 4895:1997), which has been technically revised.iv ISO 2014 All rights reservedBS EN ISO 4895

23、:2014ISO 4895:2014(E)IntroductionThe tendency of liquid epoxy resins to crystallize varies depending on factors such as basic composition, purity, additives, homogeneity and water content, in addition to external factors such as storage history and ambient temperature.As it is rather difficult to in

24、dicate the tendency quantitatively by observation and comparison, the tendency is therefore to express the results by observing, at intervals, the changes in fluidity and appearance of samples. ISO 2014 All rights reserved vBS EN ISO 4895:2014BS EN ISO 4895:2014Plastics Liquid epoxy resins Determina

25、tion of tendency to crystallizeSAFETY STATEMENT Persons using this document should be familiar with normal laboratory practice, if applicable. This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user to establish appr

26、opriate safety and health practices and to ensure compliance with any regulatory requirements.1 ScopeThis International Standard specifies a method for determining the tendency of liquid epoxy resins to crystallize. The tendency to crystallize is determined by observing, at specified time intervals,

27、 changes in fluidity and the onset of crystallization.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest ed

28、ition of the referenced document (including any amendments) applies.ISO 6353-2:1983, Reagents for chemical analysis Part 2: Specifications First seriesISO 6353-3:1987, Reagents for chemical analysis Part 3: Specifications Second series3 PrincipleCalcium carbonate powder is mixed with the liquid epox

29、y resin dissolved in ethanol. The mixture is kept at a specified low temperature and observed at specified time intervals to compare the changes in fluidity and crystallization.4 Reagents4.1 Calcium carbonate, as specified in ISO 6353-3:1987, R 53.4.2 Ethanol, as specified in ISO 6353-2:1983, R 11.5

30、 Apparatus5.1 Refrigerator or cold enclosure, maintained at (10 2) C.5.2 Glass test tube, of capacity approximately 100 ml, 40 mm in diameter and 80 mm in height, with a polyethylene-covered stopper.5.3 Glass rod, of hard glass, approximately 10 mm in diameter.5.4 Oven.5.5 Analytical balance, accura

31、te to 0,01g.INTERNATIONAL STANDARD ISO 4895:2014(E) ISO 2014 All rights reserved 1BS EN ISO 4895:2014ISO 4895:2014(E)5.6 Constant temperature room maintained at (23 5)C.6 Procedure6.1 Weigh 20 g of liquid epoxy resin into the test tube (5.2).6.2 Stopper the test tube and place it in the oven (5.4) a

32、t (60 2) C for 16 h.6.3 Cool the test tube to room temperature (23 5) C in the constant temperature room (5.6), add 20 g of calcium carbonate (4.1) and 2 g of ethanol (4.2), and mix the sample thoroughly with the glass rod for 2 min.6.4 Stopper the test tube again and place it in the vertical positi

33、on in the refrigerator or cold enclosure (5.1) at (10 2) C.6.5 Observe the sample twice a day at a specified time (for example at an interval of 8 h during the day and 16 h during the night): to start at 9 am; to carry out first observation at 5 pm; to carry out second observation at 9 am (next day)

34、; to carry out third observation at 5 pm (next day); to carry out fourth observation at 9 am (the day after).Observe the sample in the following way.Allow the test tube to warm to room temperature (23 5) C in the constant temperature room (5.6), then place it in the horizontal position and leave it

35、for 1 min. When the distance of movement of the liquid surface tip (L in Figure 1) is 10 mm and more, record “a”. When the distance of movement of the liquid surface tip (L in Figure 1) is less than 10 mm, record “b”. When the sample has completely solidified due to crystallization, record “c”.Figur

36、e 1 Observation of samplesAfter each observation, if the sample has not yet crystallized, mix thoroughly with the glass rod for 2 min and place into refrigerator until next observation.Record the number of days which elapse to each stage of crystallization (see Figure 2).2 ISO 2014 All rights reserv

37、edBS EN ISO 4895:2014ISO 4895:2014(E)KeyAn arrow indicates the time when the test was discontinued because of no further change.Figure 2 Results of the interlaboratory tests7 Expression of resultsThe tendency of a liquid epoxy resin to crystallize is expressed as the number of days which elapse unti

38、l each stage specified in 6.5, “a”, “b” and “c”, is reached.8 PrecisionPrecision in the generally accepted sense of the term for test methods cannot be determined here since it is a tendency which is being assessed.However, interlaboratory tests conducted in Japan have shown that this method is curr

39、ently more reliable and environmentally more acceptable than the previous edition (ISO 4895:1987).9 Test reportThe test report shall include the following particulars:a) a reference to this International Standard, i.e. ISO 4895;b) all details necessary for identification of the sample tested;c) the

40、results of the test;d) the date of the test;e) any deviation, by agreement or otherwise, from the specified procedure. ISO 2014 All rights reserved 3This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standa

41、rds-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring togeth

42、er business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organiza

43、tions of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services tea

44、m or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards D

45、evelopment Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant acc

46、ess to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in sing

47、le copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and

48、 the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For f

49、urther information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set o