BS EN ISO 3908-2009 Hardmetals - Determination of insoluble (free) carbon - Gravimetric method《硬质合金 不溶性(游离)碳含量的测定 重量法》.pdf

《BS EN ISO 3908-2009 Hardmetals - Determination of insoluble (free) carbon - Gravimetric method《硬质合金 不溶性(游离)碳含量的测定 重量法》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 3908-2009 Hardmetals - Determination of insoluble (free) carbon - Gravimetric method《硬质合金 不溶性(游离)碳含量的测定 重量法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO3908:2009ICS 77.160NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDHardmetals Determination ofinsoluble (free) carbon Gravimetric method(ISO 3908:2009)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIThi

2、s British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 March2010 BSI 2010ISBN 978 0 580 56455 0Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 3908:2009National forewordThis British Standard is the UK implementation of EN ISO 3908:2

3、009. Itsupersedes BS EN 23908:1993 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/65, Sintered metal components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to in

4、clude all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORM

5、E EUROPENNE EUROPISCHE NORM EN ISO 3908 October 2009 ICS 77.160 Supersedes EN 23908:1993English Version Hardmetals - Determination of insoluble (free) carbon - Gravimetric method (ISO 3908:2009) Mtaux-durs - Dosage du carbone insoluble (libre) - Mthode gravimtrique (ISO 3908:2009) Hartmetalle - Best

6、immung des unlslichen (freien) Kohlenstoffgehaltes - Gravimetrisches Verfahren (ISO 3908:2009) This European Standard was approved by CEN on 29 September 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard t

7、he status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Ger

8、man). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech

9、Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPE

10、N DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3908:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/0

11、7/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009EN ISO 3908:2009 (E) 3 Foreword This document (EN ISO 3908:2009) has been prepared by Technical Committee ISO/TC 119 “Powder metallurgy“. This European Standard shall be given the status of a national standard, either by publication of an id

12、entical text or by endorsement, at the latest by April 2010, and conflicting national standards shall be withdrawn at the latest by April 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held r

13、esponsible for identifying any or all such patent rights. This document supersedes EN 23908:1993. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czec

14、h Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 3908:2009

15、has been approved by CEN as a EN ISO 3908:2009 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009ISO 3908:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardiza

16、tion) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be

17、represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standard

18、s are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Interna

19、tional Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3908 was

20、prepared by Technical Committee ISO/TC 119, Powder metallurgy, Subcommittee SC 4, Sampling and testing methods for hardmetals. This third edition cancels and replaces the second edition (ISO 3908:1985), which has been technically revised. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/

21、2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009INTERNATIONAL STANDARD ISO 3908:2009(E) ISO 2009 All rights reserved 1Hardmetals Determination of insoluble (free) carbon Gra

22、vimetric method 1 Scope This International Standard specifies a gravimetric method for the determination of the mass fraction of insoluble (free) carbon in carbides and hardmetals. This method is applicable to carbides of hafnium, molybdenum, niobium, tantalum, titanium, vanadium, tungsten and zirco

23、nium, mixtures of these carbides and binder metals, free of lubricant, and all grades of presintered or sintered hardmetals, produced from these carbides, having a mass fraction of insoluble carbon between 0,02 % and 0,5 %. 2 Normative references The following referenced documents are indispensable

24、for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3907:2009, Hardmetals Determination of total carbon Gravimetric method 3 Principle Decomposition o

25、f the carbides and determination of the insoluble carbon by a gravimetric method. 4 Reagents During the analysis, use only reagents of recognized analytical grade, and only distilled water or water of equivalent purity. 4.1 Nitric acid, = 1,20 g/ml. Add 2 000 ml of nitric acid, = 1,42 g/ml, to 3 000

26、 ml of water. 4.2 Hydrofluoric acid, = 1,12 g/ml. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009ISO 3908:2009(E) 2 ISO 2009 All rights reserved5 Apparatus Ordinary laboratory apparatus and the following. 5.1 Apparatus, as specif

27、ied in ISO 3907. 5.2 Platinum dish, of capacity 200 ml. 5.3 Filter device: ceramic filter device or bed of suitable refractory fibrous or powder material in a Gooch crucible. NOTE If necessary, pretreat the refractory material at 800 C to 1 000 C under strongly oxidizing conditions for a minimum of

28、3 h. If pretreated, store it in a desiccator. 5.4 Vacuum filtration assembly. 6 Sampling 6.1 The sample shall be crushed to a powder in a mortar made of a material which does not alter the sample composition. The powder shall pass through a 180 m sieve. 6.2 The analysis shall be carried out on two o

29、r three test portions. 7 Procedure 7.1 Test portion Weigh, to the nearest 0,01 g, approximately 2,5 g of the test sample. 7.2 Attack Transfer the test portion (7.1) into the platinum dish (5.2). Add 75 ml of the nitric acid (4.1) and place the dish on a steam bath for 5 min. Add, drop by drop, 10 ml

30、 of the hydrofluoric acid (4.2), and leave the dish on the steam bath for about 1 h until complete dissolution is obtained. Cool the solution to ambient temperature. CAUTION Hydrofluoric and nitric acids are very dangerous chemicals. Any contact with these acids or inhalation of their vapours shall

31、be avoided. All operations with these acids shall be carried out in a fume-cupboard with good ventilation. 7.3 Preparation of the Gooch crucible Insert the ceramic filter device (5.3) into the crucible. If a refractory material is used, fill the crucible to a depth of approximately 8 mm to 10 mm and

32、 press it down so that the residue will be retained on the refractory material and the time of filtering will not be too slow. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009ISO 3908:2009(E) ISO 2009 All rights reserved 37.4 Filt

33、ering Before filtering, add a limited quantity of water to avoid the precipitation of tungstic acid. Filter the contents of the dish (see 7.2) through the filter device (5.3). Then rinse the dish twice with small volumes of water. Be sure that all particles of carbon are transferred to the filter de

34、vice. Rinse the dish again with water at least twice and then wash the filter device free from acid with hot water (about 500 ml is usually needed). Remove the wet filter device from the Gooch crucible and transfer the wet filter device into a boat (see ISO 3907:2009, 4.1.5). Dry it at 110 C. 7.5 Bl

35、ank test Carry out two blank tests for each series of determinations. Prepare the Gooch crucible in accordance with 7.3. Filter through the filter device (5.3) a mixture of 75 ml of the nitric acid (4.1) and 10 ml of the hydrofluoric acid (4.2) and proceed in accordance with 7.4. 7.6 Determination B

36、urn the filter device (5.3) in a stream of oxygen in accordance with ISO 3907. Use a furnace with an inner temperature of the tube of approximately 1 200 C. 8 Expression of results 8.1 Calculation The mass fraction of carbon , expressed as a percentage, is given by the formula 21027,29mmm where m0is

37、 the mass, in grams (g), of the test portion; m1is the mass, in grams (g), of carbon dioxide obtained from the blank test; m2is the mass, in grams (g), of carbon dioxide obtained from the combustion of the test portion; 27,29 is the carbon dioxide to carbon conversion factor, multiplied by 100. 8.2

38、Tolerances The deviation between two or three independent determinations shall not exceed the values shown in Table 1. Table 1 Tolerances Total carbon mass fraction Range for two determinations Range for three determinations % % % from 0,02 to 0,1 0,02 0,03 over 0,1 to 0,5 0,04 0,05 Licensed Copy: W

39、ang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009ISO 3908:2009(E) 4 ISO 2009 All rights reserved8.3 Final result Report the arithmetical mean of acceptable determinations rounded to the nearest 0,01 % (mass fraction). 9 Test report The test report

40、 shall include the following information: a) a reference to this International Standard; b) all details necessary for the identification of the test sample; c) the result obtained; d) all operations not specified in this International Standard, or regarded as optional; e) details of any occurrence w

41、hich may have affected the result. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO 3908:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 05/07/2010 07:52, Uncontrolled Copy, (c) BSIBS EN ISO3908:2009BSI GroupHeadquarters 389Chisw

42、ick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter

43、.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or am

44、biguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat s

45、ubscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard

46、 from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Eu

47、ropean andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Sub

48、scribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online

49、access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 n