BS EN ISO 105-Z07-1998 Textiles Tests for colour fastness Determination of application solubility and solution stability of water-soluble dyes《纺织品 色牢度试验 水溶性染料的溶液稳定性和应用溶解度的测定》.pdf

《BS EN ISO 105-Z07-1998 Textiles Tests for colour fastness Determination of application solubility and solution stability of water-soluble dyes《纺织品 色牢度试验 水溶性染料的溶液稳定性和应用溶解度的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 105-Z07-1998 Textiles Tests for colour fastness Determination of application solubility and solution stability of water-soluble dyes《纺织品 色牢度试验 水溶性染料的溶液稳定性和应用溶解度的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 105-Z07:1998 Textiles Tests for colour fastness Part Z07: Determination of application solubility and solution stability of water-soluble dyes (ISO 105-Z07:1995) The European Standard EN ISO 105-Z07:1997 has the status of a British Standard ICS 59.080.01BSENISO 105-Z07:199

2、8 This British Standard, having been prepared under the directionof the Sector Board forMasterials and Chemicals, waspublished under the authorityof the Standards Boardand comes into effect on 15 January 1998 BSI 04-1999 ISBN 0 580 29451 X National foreword This British Standard is the English langu

3、age version of ENISO 105-Z07:1997. It is identical with ISO105-Z07:1995. The UK participation in its preparation was entrusted by Technical Committee TCI/25, Chemical properties, to Subcommittee TCI/25/-/10, Colour fastness, which has the responsibility to: aid enquirers to understand the text; pres

4、ent to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee ca

5、n be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement the

6、se international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary

7、 provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theENISO t

8、itle page, page 2, the ISO title page, page ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publicat

9、ion Amd. No. Date CommentsBSENISO 105-Z07:1998 BSI 04-1999 i Contents Page National foreword Inside front cover Foreword 2 Foreword ii Text of ISO 105-Z07 1ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 105-Z07 September 1997 ICS 59.080.10 Descriptors: See ISO document English vers

10、ion Textiles Tests for colour fastness Part Z07: Determination of application solubility and solution stability of water-soluble dyes (ISO 105-Z07:1995) Textiles Essais de solidit des teintures Partie Z07: Dtermination de la solubilit lapplication et de la stabilit en solution des colorants solubles

11、 dans leau (ISO 105-Z07:1995) Textilien Farbechtheitsprfungen TeilZ07: Bestimmung der Lslichkeit und der Lsungsbestndigkeit von wasserlslichen Farbstoffen (ISO 105-Z07:1995) This European Standard was approved by CEN on 24August1997. CEN members are bound to comply with the CEN/CENELEC Internal Regu

12、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This E

13、uropean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the n

14、ational standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europis

15、ches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 105-Z07:1997 EENISO 105-Z07:1997 BSI 04-1999 2 Foreword The text of the International Standar

16、d from Technical Committee ISO/TC38 “Textiles” of the International Organization for Standardization (ISO) has been taken over as an European Standard by Technical Committee CEN/TC248 “Textiles and textile products”, the secretariat of which is held by BSI. This European Standard shall be given the

17、status of a national standard, either by publication of an identical text or by endorsement, at the latest by month of March1998, and conflicting national standards shall be withdrawn at the latest by March1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations

18、of the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of

19、the International Standard ISO105-Z07:1995 has been approved by CEN as a European Standard without any modification. NOTENormative references to International Standards are listed in Annex ZA (normative). Contents Page Foreword 2 1 Scope 1 2 Normative references 1 3 Principle 1 4 Apparatus and reage

20、nts 1 5 Preparation of solutions 2 6 Filtering the solutions 2 7 Evaluation 2 8 Test report 3 Annex A (informative) Factors affecting results 4 Annex ZA (normative) Normative referencestointernational publicationswiththeirrelevant Europeanpublications Inside back coverENISO105-Z07:1997 ii BSI 04-199

21、9 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a

22、 technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matte

23、rs of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. International Standard ISO105-Z07

24、was prepared by Technical Committee ISO/TC38, Textiles, Subcommittee SC1, Tests for coloured textiles and colorants. ISO105 was previously published in thirteen “parts”, each designated by a letter (e.g.“Part A”), with publication dates between 1978 and 1985. Each part contained a series of “section

25、s”, each designated by the respective part letter and by a two-digit serial number (e.g.“Section A01”). These sections are now being republished as separate documents, themselves designated “parts” but retaining their earlier alphanumeric designations. A complete list of these parts is given in ISO1

26、05-A01. Annex A of this part of ISO105 is for information only. Descriptors: Textiles, dyeing, colour fastness, dyes, tests, colour fastness tests, determination, solubility.ENISO 105-Z07:1997 BSI 04-1999 1 1 Scope This part of ISO105 describes a method for the determination of the application solub

27、ility of water-soluble dyes in the range 40 C to 90 C and of their solution stability. The method is not intended to measure absolute solubility. NOTE 1Several factors which may influence test results are listed in Annex A. 2 Normative references The following standards contain provisions which, thr

28、ough reference in this text, constitute provisions of this part of ISO105. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO105 are encouraged to investigate the possibility of applying the most r

29、ecent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 1773:1976, Laboratory glassware Boiling flasks (narrow-necked). ISO 3696:1987, Water for analytical laboratory use Specification and test methods. 3 Principle Se

30、veral solutions of known concentration, including the solubility limit, of the dye to be tested are prepared at a specified temperature. The solutions are then filtered under suction at this temperature in a heatable Nutsch filter and the application solubility limit determined by visual assessment

31、of the filter residues and the measured flow-through time of the filtrate. The application solubility of dyes is normally determined at 90 C. For certain classes of dyes the solubility is determined at a lower temperature. In selecting the test temperature, the manufacturers recommendations are foll

32、owed. The temperature is indicated in the test report (e.g.application solubility limit determined at 90 C, 60 C, etc.). The solution stability of dyes is determined by storing for 2h and, as the case requires, cooling the above-mentioned solution before filtration and assessment. The dissolving and

33、 storage temperatures are indicated in the test report (e.g.solution stability at 90 C/60 C, 60 C/60 C, etc.). 4 Apparatus and reagents 4.1 Erlenmeyer flask, wide-mouthed, capacity500ml, complying with ISO1773. 4.2 Heating bath, thermostatically controlled, with magnetic stirring bar 40mm long by 6m

34、m diameter, speed of stirrer 500r/min to 600r/min. 4.3 Water bath, with temperature regulator (heating/cooling) for adjusting the storage temperature (e.g.60 C, 30 C or 25 C). 4.4 Nutsch filter (Bchner funnel), heatable, of glass, steel or porcelain, of inner diameter 70mm, capacity at least 200ml,

35、having more than 100holes with a total surface area of holes (evenly distributed) of not less than 200mm 2 . 4.5 Thermostatic device (optional), with circulation pump to adjust temperature of Nutsch filter. 4.6 Vacuum apparatus 4.6.1 Suction bottle, capacity 1 litre to 2 litres. 4.6.2 Piston or memb

36、rane pump, of sufficiently high suction capacity to create a full vacuum of at least 50kPa under pressure. 4.6.3 Apparatus to adjust and maintain a given vacuum, preferably coupled with a manometer. 4.7 Stopwatch, to measure flow-through time. 4.8 Filter paper, circular, 70mm 2mm diameter. NOTE 2Fil

37、ter papers of the following characteristics have been found suitable: SeeISO105-A01:1994, clause 8, note 1 for information on sources of supply of suitable filter paper. The type of filter paper used and the manufacturer shall be listed in the test report. Property Two typical sets of values Grammag

38、e, g/m 2 92 121 Thickness, 4m 210 330 Air resistance, Gurley, s/100ml 3,6 1 Wet burst strength, kPa 1 4 Surface appearance smooth smoothENISO 105-Z07:1997 2 BSI 04-1999 4.9 Water, complying with grade3 of ISO3696, used as dye solvent. An amount of 200ml is designated as normal. More water may be add

39、ed to the solution, but such additions shall be reported together with the dye solubility values. NOTE 3No account is taken of changes in volume as a function of temperature, or those caused by the addition of dye. 5 Preparation of solutions 5.1 The concentrations at which the dye solutions are prep

40、ared shall be chosen considering the expected application solubility limit of the dye: 5.2 To determine solubility at 90 C, paste a known amount of the test dye and introduce it into the wide-mouthed Erlenmeyer flask (4.1) with a portion of the 200ml water (4.9) at about 60 C, but not in excess of t

41、he dissolving temperature of the dye. When the dye is completely wetted out, add the rest of the water to the flask. Place this solution into the heating bath (4.2) maintained at 95 C. Switch on the magnetic stirrer. When the solution has attained a temperature of95 C 2 C, continue stirring at this

42、temperature for a further 5min (total stirring time approximately 10min). Then filter the solution (seeclause 6) immediately to determine the solubility of the dye at 90 C. Repeat the process for each concentration of dye under test. 5.3 To determine solubility at temperatures below 90 C, paste a kn

43、own graduated amount of the test dye and introduce it into a wide-mouthed Erlenmeyer flask with a portion of the 200ml water(4.9) at the desired dissolving temperature until the dye is completely wetted out. Then add the rest of the water to the flask. Place the solution in the heating bath maintain

44、ed at the desired dissolving temperature; stir the solution for 10 min and then filter (seeclause6). Repeat the process for each concentration of dye under test. 5.4 To determine the solution stability at the desired temperature (e.g. 60 C, 30 C or 25 C), place the Erlenmeyer flask with the solution

45、 prepared according to 5.1 or 5.2 into a bath maintained at the desired temperature (see4.3) and allow to stand for 2h before filtration. Before filtering, mix the solution thoroughly by tilting the flask to and fro. 6 Filtering the solutions NOTE 4In order to avoid any temperature shock effects, it

46、 is essential that heated solutions are filtered through equipment already brought to the same temperature as the solution under test. Ideally this is best done using a jacketed filter funnel, but acceptable results can also be obtained using preheated funnels, either by immersion in a water bath or

47、 oven, or by passing water preheated to the test temperature through the equipment immediately prior to carrying out the test. When using this latter technique, the amount of water should be determined locally in order that the filter funnel can be heated to the same temperature irrespective of its

48、geometry and the ambient conditions. In all cases when using preheating techniques rather than a jacketed funnel, the test solution should be passed through the test equipment immediately after removing it from its heating medium. 6.1 Preheat the Nutsch filter (4.4) to the test temperature and maint

49、ain at this temperature throughout the entire filtration operation. 6.2 Immediately before filtering, wet out two filter papers (4.8) in the Nutsch filter in a double layer using at least 50ml water at the test temperature. 6.3 Adjust the vacuum (4.6) to 3kPa to 4kPa, which is equivalent to 300mm to 400mm water column pressure. 6.4 Filter the dye solution obtained as in 5.1, 5.2 or5.3 at the recommended temperature and measure the flow-through time with a stopwatch. Visually examine the flask which contain