BS EN 61969-2-2012 Mechanical structures for electronic equipment Outdoor enclosures Coordination dimensions《电子设备机械构造 室外机壳 协调尺寸规格》.pdf

《BS EN 61969-2-2012 Mechanical structures for electronic equipment Outdoor enclosures Coordination dimensions《电子设备机械构造 室外机壳 协调尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS EN 61969-2-2012 Mechanical structures for electronic equipment Outdoor enclosures Coordination dimensions《电子设备机械构造 室外机壳 协调尺寸规格》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationMechanical structures for electronic equipment Outdoor enclosuresPart 2: Coordination dimensionsBS EN 61969-2:2012National forewordThis British Standard is the UK implementation

2、of EN 61969-2:2012. It isidentical to IEC 61969-2:2011. It supersedes BS EN 61969-2:2000, BS EN61969-2-1:2000 and BS EN 61969-2-2:2000, which are withdrawn.The UK participation in its preparation was entrusted to Technical CommitteeEPL/48, Electromechanical components and mechanical structures for e

3、lectronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Publis

4、hed by BSI Standards Limited 2012ISBN 978 0 580 67586 7ICS 31.240 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 29 February 2012.Amendments issued since publicat

5、ionAmd. No. Date Text affectedBRITISH STANDARDBS EN 61969-2:2012EUROPEAN STANDARD EN 61969-2 NORME EUROPENNE EUROPISCHE NORM February 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung

6、Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61969-2:2012 E ICS 31.240 Supersedes EN 61969-2:2000, EN 61969-2-1:2000, EN 61969-2-2:2000English version Mechanical struc

7、tures for electronic equipment - Outdoor enclosures - Part 2: Coordination dimensions (IEC 61969-2:2011) Structures mcaniques pour quipement lectronique - Enveloppes de plein air - Partie 2: Dimensions de coordination (CEI 61969-2:2011) Mechanische Bauweisen fr elektronische Einrichtungen - Auengehu

8、se - Teil 2: Koordinationsmae (IEC 61969-2:2011) This European Standard was approved by CENELEC on 2011-12-22. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any

9、alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other lang

10、uage made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the

11、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61969-2:2012EN 61969-2

12、:2012 - 2 - Foreword The text of document 48D/482/FDIS, future edition 2 of IEC 61969-2, prepared by SC 48D, “Mechanical structures for electronic equipment“, of IEC/TC 48, “Electromechanical components and mechanical structures for electronic equipment“ was submitted to the IEC-CENELEC parallel vot

13、e and approved by CENELEC as EN 61969-2:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2012-09-22 latest date by which the national standards conflicting with the

14、document have to be withdrawn (dow) 2014-12-22 This document supersedes EN 61969-2:2000, EN 61969-2-1:2000 and EN 61969-2-2:2000. EN 61969-2:2012 includes the following significant technical changes with respect to EN 61969-2:2000: It was the intention when EN 61969-2:2000 was created that a section

15、al standard is to be followed by a detail standard, consisting of EN 61969-2-1 and EN 61969-2-2. The intention of detail standards was to create a recommended but cost-effective range of outdoor enclosure solutions offered from multiple vendors. However, it became evident that the outdoor enclosure

16、applications were extremely application specific and the intended effect became irrelevant. Consequently, EN 61969-2-1 and EN 61969-2-2 became obsolete and will be withdrawn at the time when EN 61969-2:2012 is published. To provide for a useful outdoor enclosure installation matrix EN 61969-2:2012 f

17、ocuses on overall outdoor enclosure co-ordination dimension only. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice T

18、he text of the International Standard IEC 61969-2:2011 was approved by CENELEC as a European Standard without any modification. BS EN 61969-2:2012- 3 - EN 61969-2:2012 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following

19、 documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an interna

20、tional publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60917-2 - Modular order for the development of mechanical structures for electronic equipment practices - Part 2: Sectional specification - Interface co

21、-ordination dimensions for the 25 mm equipment practice EN 60917-2 - BS EN 61969-2:2012 2 61969-2 IEC:2011 CONTENTS 1 Scope . 5 2 Normative references . 5 3 Arrangement overview 5 4 Coordination dimensions 6 4.1 General . 6 4.2 Height . 7 4.3 Width 8 4.4 Depth 8 Figure 1 Arrangement overview . 6 Fig

22、ure 2 Outdoor enclosure coordination dimensions . 7 Table 1 HEand HE1dimensions . 7 Table 2 WEand WE1dimensions . 8 Table 3 DEand DE1dimensions . 8 BS EN 61969-2:201261969-2 IEC:2011 5 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT OUTDOOR ENCLOSURES Part 2: Coordination dimensions 1 Scope This part

23、 of IEC 61969 applies to the design of enclosures for outdoor applications for stationary use at non-weatherprotected locations as defined in IEC 61969-1 Ed.2.0. The internal and external coordination dimensions are derived from IEC 60917-2. The internal dimensions meet the mounting dimensions of su

24、bracks in accordance with IEC 60917-2-2 and IEC 60297-3. The external dimensions, compared to IEC 60917-2, are partly increased in order to meet the design requirements of the outdoor specific conditions. 2 Normative references The following referenced documents are indispensable for the application

25、 of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60917-2, Modular order for the development of mechanical structures for electronic equipment practices Part 2: Sectio

26、nal specification Interface co-ordination dimensions for the 25 mm equipment practice3 Arrangement overview An example of an outdoor enclosure is given in Figure 1. Application specific roofs and/or bases/plinth, cable entry/exit and external mounted cable entry or cable management boxes are not cov

27、ered by this standard. BS EN 61969-2:2012 6 61969-2 IEC:2011 Base/plinth (see NOTE) Outdoor enclosure as defined in this specification Subrack with plug-in units or chassis Roof (see NOTE) Management box (see NOTE) Miscellaneous devices, e.g. batteries Management box (see NOTE) IEC 2455/11 NOTE The

28、enclosure may be closed by doors and at the top and/or bottom without the use of any additional roof or a base/plinth. Management boxes may be attached at any surface of the enclosure (inclusive doors) and are typically used for cable and/or power management etc and are application specific. Specifi

29、c roofs and/or bases may be optional for technical or appearance reasons and are not specified in this standard. Figure 1 Arrangement overview 4 Coordination dimensions 4.1 General Following the coordination rules as defined in IEC 60917-2, the external dimensions may be decreased and the aperture d

30、imensions may be decreased. Smaller parts such as locks, hinges or handles may exceed the enclosure dimension by 25 mm. However, special requirements, regulatory or application specific are exempted. The figures do not imply product design. Only the coordination dimensions are relevant. Smaller part

31、s, for example locks or handles, may exceed the enclosure dimensions by 25 mm maximum. See Figure 2 and Tables 1 to 3. BS EN 61969-2:201261969-2 IEC:2011 7 Front view Front line including doors Top view (A-A) WE1WEHE1HEDE1DEA A IEC 2456/11 Key HEoverall height HE1aperture height WEoverall width WE1a

32、perture width DEoverall depth DE1aperture depth Figure 2 Outdoor enclosure coordination dimensions 4.2 Height Table 1 HEand HE1dimensions Dimensions in millimetres HE b400 500 600 700 800 900 1 000 1 100 1 200 1 300 1 400 HE1 a150 250 350 450 550 650 750 850 950 1 050 1 150 HE b1 500 1 600 1 700 1 8

33、00 1 900 2 000 2 100 2 200 2 300 2 400 2 500 2 600 HE1 a1 250 1 350 1 450 1 550 1 650 1 750 1 850 1 950 2 050 2 150 2 250 2 350 aAperture height dimensions: HE1may be increased or decreased. Multiples of 5 mm are to be used. bFormulae for any optional outside height dimension: HE= HE1+ 200 + (n 50).

34、 BS EN 61969-2:2012 8 61969-2 IEC:2011 4.3 Width Table 2 WEand WE1dimensions Dimensions in millimetres WE b300 400 500 600 700 800 900 1 000 1 100 1 200 WE1 a200 300 400 500 500 600 700 800 900 1 000 WE b1 300 1 400 1 500 1 600 1 700 1 800 1 900 2 000 2 100 2 200 2 300 WE1 a1 100 1 200 1 300 1 400 1

35、 500 1 600 1 700 1 800 1 900 2 000 2 100 aAperture width dimensions WE1may be increased or decreased. Multiples of 5 mm are to be used. bFormulae for any optional outside width dimension from 700 mm upwards: WE= WE1+ 150 + (n 50). For width of 600 mm and smaller: WE= WE1+ (n 50). 4.4 Depth Table 3 D

36、Eand DE1dimensions Dimensions in millimetres DE b300 400 500 600 700 800 900 1 000 1 100 1 200 DE1 a200 300 400 500 600 700 800 900 1 000 1 100 aAperture depth dimensions DE1 may be increased or decreased. Multiples of 5 mm are to be used. bFormulae for any optional outside depth dimension: DE= DE1+

37、 50 + (n 50). _ BS EN 61969-2:2012This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI i

38、s incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are perio

39、dically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whil

40、e using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an indi

41、vidual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the

42、BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementati

43、on of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kep

44、t up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards

45、and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity

46、 that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval s

47、ystem or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: