BS EN 60107-7-1997 Methods of measurement on receivers for television broadcast transmission - HDTV displays《电视广播传输接收机测量方法 HDTV显示器》.pdf

《BS EN 60107-7-1997 Methods of measurement on receivers for television broadcast transmission - HDTV displays《电视广播传输接收机测量方法 HDTV显示器》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60107-7-1997 Methods of measurement on receivers for television broadcast transmission - HDTV displays《电视广播传输接收机测量方法 HDTV显示器》.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60107-7:1997 IEC 60107-7: 1997 Methods of Measurement on receivers for television broadcast transmissions Part 7: HDTV displays The European Standard EN 60107-7:1997 has the status of a British Standard ICS 33.160.20BSEN 60107-7:1997 This British Standard, having been prepared

2、 under the direction of the ElectrotechnicalSector Board, was published under the authority of the Standards Board and comes into effect on 15 July 1997 BSI 02-1999 ISBN 0 580 27736 4 National foreword This British Standard is the English language version of EN60107-7:1997. Itis identical with IEC60

3、107-7:1997. The UK participation in its preparation was entrusted by Technical Committee EPL/100, Audio, video and multimedia systems and equipment and receivers, to Subcommittee EPL/100/1, Receiving equipment, which has the responsibility to: aid enquirers to understand the text; present to the res

4、ponsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained

5、on request to its secretary. Cross-references Attention is drawn to the fact thatAnnex ZA lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BS

6、I Standards Catalogue under the section entitled “International Standards Correspondence Index”, or using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsib

7、le for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 56 and a back cover. This standard has been upda

8、ted (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN60107-7:1997 BSI 02-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of E

9、N 60107-7 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN60107-7 May1997 ICS33.160.20 Descriptors: Television receivers, HDTV, display devices, LCD, electrical properties, measurements, tests, characteristics, images, synchronisation, quality, luminance, colours English version Methods

10、 of measurement on receivers for television Part 7: HDTV displays (IEC 60107-7:1997) Mthodes de mesures pour les rcepteurs de tlvision Partie 7: Dispositifs de visualisation TVHD (CEI 60107-7:1997) Meverfahren fr Empfnger von Fernseh-Rundfunksendungen Teil 7: HDTV-Wiedergabeeinrichtungen (IEC 60107-

11、7:1997) This European Standard was approved by CENELEC on 1997-03-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogr

12、aphical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility o

13、f a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands

14、, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC Al

15、l rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN60107-7:1997 EEN60107-7:1997 BSI 02-1999 2 Foreword The text of document 100A/23/FDIS, future edition1 of IEC60107-7, prepared by SC100A, Multimedia end-user equipment, of IEC TC100, Audio, video

16、 and multimedia systems and equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN60107-7 on 1997-03-11. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. Annexes designated “informative” are given for informatio

17、n only. In this standard, Annex ZA is normative and Annex A informative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC60107-7:1997 was approved by CENELEC as a European Standard without any modification. In the official version, forAnnex A, Bibliog

18、raphy, the following note has to be added for the standard indicated: Contents Page Foreword 2 1 General 5 1.1 Scope and object 5 1.2 Normative references 5 1.3 Definitions 5 1.4 Types of displays 6 2 General notes on measurements 6 2.1 General 6 2.1.1 Operation conditions 6 Page 2.1.2 Presentation

19、of results 6 2.1.3 Environmental conditions 6 2.1.4 Precautions during measurement 6 2.1.5 Power supply 7 2.1.6 Stabilization period 7 2.1.7 Test room 7 2.2 Input signals 7 2.2.1 Video signals 7 2.3 Test signals 7 2.3.1 Video test signals (general remarks) 7 2.3.2 Audio test signals 9 2.4 Test instr

20、uments 10 2.4.1 Video test signal generator 10 2.4.2 Audio test signal generator 10 2.4.3 Oscilloscope 10 2.4.4 Luminance meter and colorimeter 10 2.4.5 Other optical measuring instruments 10 2.4.6 Measurement setup 10 2.5 Standard measuring conditions 10 2.5.1 Standard input signal levels 10 2.5.2

21、Standard output signal levels 11 2.5.3 Standard display settings 11 2.5.4 General measurement procedure 11 3 Tests under general operating conditions 12 3.1 Electrical and mechanical performance 12 3.1.1 Introduction 12 3.1.2 Methods of measurement 12 3.2 Power consumption 12 3.2.1 Method of measure

22、ment 12 4 Characteristics of displayed pictures 13 4.1 General properties of the picture 13 4.1.1 General 13 4.1.2 Geometrical distortion 13 4.1.3 Over- and under-scanning and centring 16 4.1.4 Luminance and contrast 18 4.1.5 Uniformity of luminance 19 4.1.6 Uniformity of chromaticity 20 4.1.7 Conve

23、rgence and registration errors 20 4.1.8 White balance 21 4.1.9 Resolution 21 4.1.10 Colour fidelity 21 4.1.11 Picture breathing 22 4.1.12 Local picture distortion 22 4.1.13 Sound-to-picture interference 23 4.1.14 Other characteristics of the picture 23 latest date by which the EN has to be implement

24、ed at national level by publication of an identical national standard or by endorsement (dop) 1997-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1997-12-01 IEC 65 NOTEHarmonized, together with its amendments 1:1987, 2:1989 and 3:1992, as EN60065

25、:1993 (modified).EN60107-7:1997 BSI 02-1999 3 Page 4.2 Synchronizing quality 23 4.2.1 Synchronizing range 23 4.2.2 Pulling on whites 24 4.2.3 Quality of interlace 24 4.3 Characteristics inherent in projection type displays 25 4.3.1 General 25 4.3.2 Viewing angle and dependence of luminance uniformit

26、y on the angle 25 4.3.3 Dependence of chromaticity on viewing angle 26 4.3.4 Screen gain and luminous flux index of a projector 27 4.4 Characteristics inherent in LCD displays 28 4.4.1 General 28 4.4.2 Viewing angle and dependence of luminance uniformity on the angle 29 4.4.3 Dependence of chromatic

27、ity on viewing angle 29 4.4.4 Variation of luminance with time 29 5 Characteristics of video channels 29 5.1 Characteristics of the luminance channel 29 5.1.1 General 29 5.1.2 Amplitude response to video frequency 30 5.1.3 Linear waveform response 30 5.1.4 Line time non-linearity 31 5.1.5 Black leve

28、l stability 32 5.2 Characteristics of the colour difference channel 32 5.2.1 General 32 5.2.2 Matrix error 32 5.2.3 Y/C timing 33 5.2.4 Other characteristics 33 Annex A (informative) Bibliography 55 Annex ZA (normative) Normative references to international publications with their corresponding Euro

29、pean publications 56 Figure 1 RGB primary colour bar signals 36 Figure 2 YP B P Rcomponent colour bar signals 37 Figure 3 Cross-hatch pattern 37 Figure 4 Full white and full black signals 38 Figure 5 White window 38 Figure 6 Black and white window 39 Figure 7 Line and window 40 Figure 8 Composite si

30、ne-wave signal 40 Figure 9 Multiburst signal 40 Page Figure 10 2T pulse and bar signal 41 Figure 11 Horizontal bar 41 Figure 12 Staircase signal 42 Figure 13 PLUGE 42 Figure 14 Checkered pattern signal 43 Figure 15 Notional block diagram of measurement setup 43 Figure 16 Example of outline distortio

31、n 43 Figure 17 Example of geometrical non-linearity 44 Figure 18 Outline distortion 44 Figure 19 Inner distortion 45 Figure 20 Over-scanning 45 Figure 21 Under-scanning 46 Figure 22 Centring 46 Figure 23 Measuring points for contrast 47 Figure 24 Measurements of convergence orregistration errors at

32、an intersection of cross-hatch 47 Figure 25 Measurements of convergence orregistration errors at an intersection of cross-hatch 47 Figure 26 Local picture distortion 48 Figure 27 White pulling 48 Figure 28 Quality of interlace 49 Figure 29 Interlace check pattern 49 Figure 30 Standard viewing positi

33、on 50 Figure 31 Measurement of viewing angle 51 Figure 32 Example of amplitude frequency characteristics 52 Figure 33 2T bar response 52 Figure 34 2T pulse response 52 Figure 35 Field rate square-wave response 53 Figure 36 Measurement of amplitude non-linearity 53 Figure 37 Example of amplitude non-

34、linearity 53 Figure 38 Measurement of black level stability 54 Figure 39 Example of black level stability 54 Table 1 Example of outline distortion 33 Table 2 Example of visible picture size 33 Table 3 Example of luminance uniformity 34 Table 4 Example of chromaticity uniformity of white 34 Table 5 E

35、xample of white balance 34 Table 6 Example of viewing angles measured 35 Table 7 Example of chromaticity variations on viewing angle 354 blankEN60107-7:1997 BSI 02-1999 5 1 General 1.1 Scope and object This part of IEC107 deals with the standard conditions and methods of measurement on high definiti

36、on television (HDTV) displays. Such displays may be used as an integral part of an HDTV receiver for direct off-air reception, reception via cabled networks, or as a monitor for pre-recorded video, home movies and games, among other applications. This standard deals with the determination of perform

37、ance, and permits the comparison of equipment by listing the characteristics which are useful for specifications and by laying down uniform methods of measurement for these characteristics. Performance requirements are not specified. This standard does not deal with general safety matters, for which

38、 reference should be made to IEC65 1 1)or other appropriate IEC safety standards. NOTEMethods of measurement on wide-screen displays for conventional television signals are dealt with in IEC 60107-1. 1.2 Normative references The following normative documents contain provisions which, through referen

39、ce in this text, constitute provisions of this part of IEC107. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to agreements based on this part of IEC107 are encouraged to investigate the possibility of applying the most rec

40、ent editions of the normative documents indicated below. Members of ISO and IEC maintain registers of currently valid International Standards. IEC 68, Environmental testing. IEC 68-1:1988, Environmental testing Part 1: General and guidance. IEC 60107-1:1997, Methods of measurement on receivers for t

41、elevision broadcast transmissions Part 1: General considerations Measurements at radio and video frequencies. IEC 60107-2:1997, Methods of measurement on receivers for television broadcast transmissions Part 2: Audio channels General methods and methods for monophonic channels. ITU-R Recommendation

42、BT.471-1:1994, Nomenclature and description of colour bar signals. 1.3 Definitions For the purpose of this part of IEC 107, the following definitions apply: 1.3.1 HDTV display integral part of an HDTV receiver or a monitor for displaying picture information carried by the HDTV video signals defined

43、in the Recommendation ITU-R BT.709-1 2 or similar signals with an aspect ratio of16:9 it may include audio amplifiers and loudspeakers NOTE 1The ITU-R Recommendation BT.709-1 2 defines basic parameters of HDTV signals and their signal formats for1125/60/2:1 and 1250/50/2:1 systems. NOTE 2Conventiona

44、l television displays with an aspect ratio of 16:9 are not dealt with by this standard. This type of display is dealt with by the future IEC/FDIS 107-1. 1.3.2 luminance in a given direction, the luminous intensity per unit of projected area of any surface as viewed for that direction the luminance v

45、alue is expressed in candela per square metre 1.3.3 chromaticity property of colour stimulus defined by its chromaticity co-ordinates (x, y) of the CIE1931 standard colorimetric system 3, or chromaticity co-ordinates (u9, v9) of the CIE1976 uniform chromaticity system 3 1) Figures in square brackets

46、 refer to the bibliography given inAnnex AEN 60107-7:1997 6 BSI 02-1999 1.4 Types of displays HDTV displays in this standard include direct-view types using a cathode ray tube (CRT) and liquid crystal display (LCD), and projection types using CRTs and LCDs. It is assumed that the displays are equipp

47、ed with input terminals for analogue baseband signals. 2 General notes on measurements 2.1 General Measurement shall be made in accordance with the following conditions to ensure repeatable results. If audio channels and loudspeakers are provided, characteristics of the audio channels shall be measu

48、red by the methods specified in IEC60107-2. 2.1.1 Operation conditions Unless specified otherwise in the relevant clauses, both the audio and picture parts shall be in operation and the scanning circuits shall be properly synchronized. The contrast and brightness controls should be set at the standa

49、rd settings specified in2.5. If different values are used, they shall be noted with the results. 2.1.2 Presentation of results Measurement results shall be listed in a table or presented graphically. However, the relationship between two or more quantities is often more clearly represented in a graph than as a table. When the results of a point-by-point measurement for an individual sample are presented as a continuous curve in a graph, the me