BS EN 15612-2008 Railway applications - Braking - Brake pipe accelerator valve《轨道交通 制动 制动管加速器阀门》.pdf

《BS EN 15612-2008 Railway applications - Braking - Brake pipe accelerator valve《轨道交通 制动 制动管加速器阀门》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15612-2008 Railway applications - Braking - Brake pipe accelerator valve《轨道交通 制动 制动管加速器阀门》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 15612:2008ICS 45.060.01NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRailway applications Braking Brake pipeaccelerator valveLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIThis British Standardwas publi

2、shed under theauthority of the StandardsPolicy and StrategyCommittee on 31 December2008 BSI 2008ISBN 978 0 580 58007 9Amendments/corrigenda issued since publicationDate CommentsBS EN 15612:2008National forewordThis British Standard is the UK implementation of EN 15612:2008.The UK participation in it

3、s preparation was entrusted to TechnicalCommittee RAE/4, Braking.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.

4、Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIBS EN 15612:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15612November 2008ICS 45.060.01English VersionRailway a

5、pplications - Braking - Brake pipe accelerator valveApplications ferroviaires - Freinage - Valve acclratrice devidangeBahnanwendungen - Bremse -SchnellbremsbeschleunigungsventilThis European Standard was approved by CEN on 27 September 2008.CEN members are bound to comply with the CEN/CENELEC Intern

6、al Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.

7、This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are

8、the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerlan

9、d and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15612:

10、2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIBS EN 15612:2008EN 15612:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Design and manufacture.5 4.1 General5 4.2 Functional requirements.5 4.

11、3 Vibration and shocks requirements.7 4.4 Environment requirements .7 4.5 Compressed air quality .10 4.6 Service life 10 4.7 Fire behaviour 10 4.8 External appearance10 4.9 Design requirements regarding pressure stress .10 4.10 Interfaces 11 5 Materials .11 6 Type tests .11 6.1 General11 6.2 Individ

12、ual brake pipe accelerator tests .11 6.3 Simulated train consist tests17 7 Routine test and inspection19 8 Documentation.19 9 Designation 20 10 Identification and marking 20 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 96/48/EC, as

13、 modified by Directive 2004/50/EC 21 Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2001/16/EC of the European Parliament and of the Council of 19 March 2001 on the interoperability of the trans-European conventional rail system, as

14、modified by EU Directive 2004/50/EC of 29 April 2004 .22 Bibliography 23 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIBS EN 15612:2008EN 15612:2008 (E) 3 Foreword This document (EN 15612:2008) has been prepared by Technical Committee CEN/TC 256 “

15、Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May

16、 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard has been prepared under a mandate given to CEN/CENELEC/E

17、TSI by the European Commission and the European Free Trade Association and supports essential requirements of EU Directive 96/48 and EU Directive 2001/16, as modified by EU Directive 2004/50. For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this d

18、ocument. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland

19、, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIBS EN 15612:2008EN 15612:2008 (E) 4

20、 1 Scope This European Standard is applicable to brake pipe accelerator valves designed to vent the brake pipe of railway vehicles when an emergency brake application is initiated, without taking the type of vehicles and track-gauge into consideration. This European Standard specifies the requiremen

21、ts for the design, manufacture and testing of brake pipe accelerator valves. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refer

22、enced document (including any amendments) applies. EN 14478:2005, Railway applications Braking Generic vocabulary EN 14601, Railway applications Straight and angled end cocks for brake pipe and main reservoir pipe EN 15355, Railway applications Braking - Distributor valves and distributor-isolating

23、devices EN 50125-1, Railway applications Environmental conditions for equipment Part 1: Equipment on board rolling stock EN 60721-3-5:1997, Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Section 5: Ground vehicle installat

24、ions (IEC 60721-3-5:1997) EN 61373:1999, Railway applications Rolling stock equipment Shock and vibration tests (IEC 61373:1999) EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) ISO 8573-1:2001, Compres

25、sed air Part 1: Contaminants and purity classes 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14478:2005 and the following apply. 3.1 brake pipe accelerator valve device connected to the brake pipe of a vehicle, which operates in response to seeing

26、a rapid fall in brake pipe pressure to ensure a continuing rapid fall to below 2,5 bar 3.2 braking mode “goods ” braking mode “freight” braking mode “G“ braking mode characterized by slow brake application and release times specific for distributor valves used on freight trains for slow speed 3.3 br

27、aking mode “passenger” braking mode “P” braking mode characterized by fast brake application and release times specific for distributor valves used on trains for passenger traffic Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIBS EN 15612:2008EN 15

28、612:2008 (E) 5 3.4 normal litre Nl unit of mass for gases equal to the mass of 1 l at a pressure of 1,013 2 bar (one atmosphere) and at a standard temperature, often 0 C or 20 C NOTE Airflow is often stated in normal litres per minute (Nl/min). 3.5 operating pressure reference input pressure in full

29、 release position NOTE This is normally 5 bar brake pipe pressure but can be 4 bar or 6 bar. 3.6 quick service function function of a distributor valve which allows, when applying the brake from stand-by and released position, the local fast venting of brake pipe pressure by a certain specified amou

30、nt and at a certain specified gradient, to provide pneumatic brake signal transmission through a train 3.7 quick service device device that fulfils the quick service function 3.8 emergency brake application brake pipe pressure fall seen at the accelerator valve as a result of a demand for an emergen

31、cy brake application from any source 3.9 overcharge increase in brake pipe pressure above normal operating pressure 4 Design and manufacture 4.1 General The design and manufacture of the brake pipe accelerator valves shall take the requirements of this standard into account for all intended operatin

32、g conditions. 4.2 Functional requirements 4.2.1 General Brake pipe accelerator valves shall be able to operate with all interoperable distributors and existing interoperable brake pipe accelerator valves. The brake pipe accelerator valve shall be ready to operate when the brake pipe has reached its

33、operating (running) pressure. The brake pipe accelerator valve shall operate in response to a defined rapid fall of brake pipe pressure to ensure a continuing rapid fall to below 2,5 bar. 4.2.2 Operating requirements The following operating requirements are defined in relation to a 5 bar brake pipe

34、operating (running) pressure. When an emergency brake application occurs, the brake pipe accelerator valves shall create a sufficiently rapid reduction in brake pipe pressure to ensure the rapid increase in brake cylinder pressure on every vehicle Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARD

35、S, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIBS EN 15612:2008EN 15612:2008 (E) 6 in the train set. When the pressure in the brake pipe has fallen quickly to below 2,5 bar, and within no more than 4 s after the brake pipe accelerator valve commences operation, the brake pipe accelerator valve shall

36、 stop venting air in such a way that the brake pipe can rapidly be refilled. This requirement shall be proven by testing in accordance with 6.2.4.4. No functional errors shall occur in the operation of the brake pipe accelerator valve at operating (running) pressures of (5 1) bar. This requirement s

37、hall be proven by testing in accordance with 6.2.4.10. 4.2.3 Train/vehicle behaviour The brake pipe accelerator valve shall exhaust the air from the brake pipe without causing any adverse effect on vehicle/train behaviour. This requirement shall be proven by testing in accordance with 6.3. 4.2.4 Aff

38、ect of overcharge 4.2.4.1 Overcharge after full service application The brake pipe accelerator valve shall not come into operation due to the effect of an operating pressure overcharge after a full service brake application, which allows a build up of brake pipe pressure above normal operating press

39、ure to 6 bar. It shall be taken into account that this overcharge can be present for up to 40 s in braking mode “G” and 10 s in braking mode “P” after a full service application. This requirement shall be proven by testing in accordance with 6.2.4.8. 4.2.4.2 Overcharge starting from operating pressu

40、re The brake pipe accelerator valve shall not come into operation if the brake pipe pressure, starting from the operating pressure, is raised to 6 bar for 2 s, then is reduced to 5,2 bar in 1 s, followed by a return to the operating pressure at a rate of 0,15 bar in 60 s. This requirement shall be p

41、roven by testing in accordance with 6.2.4.9. 4.2.5 Affect of individual vehicle The operation of the brake pipe accelerator valve shall not be affected by an individual vehicle with a brake pipe volume not exceeding 25 l, where a brake pipe accelerator valve is not fitted or the brake has been isola

42、ted. This shall apply irrespective of the position of that vehicle in the train consist. This requirement shall be proven by testing in accordance with 6.3. 4.2.6 Subsequent emergency application The brake pipe accelerator valve shall come into operation when an emergency brake application is made a

43、fter a full service brake application. This requirement shall be proven by testing in accordance with 6.2.4.7. 4.2.7 Sensitivity The brake pipe accelerator valve shall come into operation no later than 2 s after the pressure in the brake pipe, venting to atmosphere, has fallen from 5 bar to 3,2 bar

44、within 3 s. This requirement shall be proven by testing in accordance with 6.2.4.4. 4.2.8 Insensitivity to brake pipe pressure fall The brake pipe accelerator valve shall not come into operation when the pressure in the brake pipe falls uniformly from 5 bar to 3,2 bar over 6 s with the distributor i

45、noperative. Continuing the pressure fall down to 2,5 bar shall not cause the brake pipe accelerator valve to operate. This requirement shall be proven by testing in accordance with 6.2.4.5. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/05/2009 01:56, Uncontrolled Copy, (c) BSIBS EN 15612

46、:2008EN 15612:2008 (E) 7 4.2.9 Insensitivity to distributor valve quick service device operation The brake pipe accelerator valve shall not operate during the initial stage of service braking due to operation of the distributor valve internal quick service device. This requirement shall be proven by

47、 testing in accordance with 6.2.4.6. 4.2.10 Isolation 4.2.10.1 If the brake pipe accelerator valve is incorporated in the distributor, it shall be inoperative after the distributor has been isolated. This requirement shall be proven by testing in accordance with EN 15355 as part of the distributor v

48、alve test. 4.2.10.2 If the brake pipe accelerator valve is fitted separately from the distributor it shall be possible to isolate the brake pipe accelerator valve from the brake pipe and vent its pressure, using a suitable valve or device in the pipework such that it can be sealed in the normal open

49、 position with the isolating handle in the vertical down position. NOTE This requirement will be specified in the relevant vehicle system standard. 4.2.11 Leakage Leakage of the brake pipe accelerator valve shall be such that technical performance as specified by this standard is met without restrictions. The sealing arrangement within the brake pipe accelerator valve shall prevent loss of air as follows when considering a brake pipe operating pressure of 6 bar: At an environmental temperature of (20 5) C, the brake pipe accelerator valve shall