BS EN 12743-1999 Footwear Test methods for outsoles Compression energy《鞋靴 外底试验方法 压缩能量》.pdf

《BS EN 12743-1999 Footwear Test methods for outsoles Compression energy《鞋靴 外底试验方法 压缩能量》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12743-1999 Footwear Test methods for outsoles Compression energy《鞋靴 外底试验方法 压缩能量》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12743:1999 Incorpor

2、ating Corrigendum No.1 The European Standard EN 12743:1999 has the status of a British Standard ICS 61.060 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Footwear Test methods for outsoles Compression energyThis British Standard, having been prepared under the direction of th

3、e Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 December 1999 BSI 08 January 2002 ISBN 0 580 35240 4 BS EN 12743:1999 Amendments issued since publication Amd. No. Date Comments 13350 Corrigendum No. 1 08 January

4、 2002 Indicated by a sideline National foreword This British Standard is the English language version of EN 12743:1999, including corrigendum May 2001. The UK participation in its preparation was entrusted to Technical Committee TCI/69, Footwear and leather, which has the responsibility to: aid enqu

5、irers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on

6、this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”

7、, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself conf

8、er immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in th

9、is document indicates the most recent changes by amendment.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12743 September 1999 ICS 61.060 Incorporating corrigendum May 2001 English version Footwear Test methods for outsoles Compression energy Chaussures - Mthodes dessai applicables aux semelle

10、s - Mesure de lnergie de compression Schuhe - Prfverfahren fr Laufsohlen - Kompressionenergie This European Standard was approved by CEN on 9 August 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st

11、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A

12、 version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland,

13、 France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels 1

14、999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12743:1999 EPage 2 EN 12743:1999 BSI 08 January 2002 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Definitions . 4 4 Apparatus and material. 4 5 Sampling and condi

15、tioning 5 6 Test method 5 7 Expression of results. 5 8 Test Report . 6 Bibliography 8Page 3 EN 12743:1999 BSI 08 January 2002 Foreword This European Standard has been prepared by Technical Committee CEN/TC 309, Footwear, the Secretariat of which is held by AENOR. This European Standard shall be give

16、n the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2000, and conflicting national standards shall be withdrawn at the latest by March 2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations o

17、f the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 4 EN 12743:1999 BSI 08 Janu

18、ary 2002 1 Scope This European Standard specifies a method for the determination of the compression energy of outsoles. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriat

19、e places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication

20、 referred to applies. EN 12222 Footwear - Standard atmospheres for conditioning and testing of footwear and components for footwear. prEN 13400:1998 Footwear - Sampling location of components for footwear. ISO 5893 Rubber and plastic test equipment - Tensile, flexural and compression types (constant

21、 rate of traverse) - Description. 3 Definitions For the purpose of this standard the following definition applies: compression energy: the energy in joules corresponding to the deformation of a material under a fixed force of 5 000 newtons. 4 Apparatus and material The following apparatus and materi

22、al shall be used: 4.1 Tensile-testing machine The tensile-testing machine shall comply with the requirements of ISO 5893, to an accuracy corresponding to grade B, with a constant rate of traverse of 10 mm/min 2 mm/min. A low-inertia machine having autographic force recording facilities is required.

23、4.2 Test punch, being the back part of a standardized last made in polyethylene. The last is sectioned on a plane vertical to the feather edge and at 90 to the axis of the back part (see figure 1). The length of the punch in relation to footwear size is given in table 1.Page 5 EN 12743:1999 BSI 08 J

24、anuary 2002 Table 1 Summarising chart of measurements for footwear SIZE DIMENSIONS MONDOPOINT mm FRENCH SIZES ENGLISH SIZES L mm l mm H mm h mm D mm up to 235 up to 36 up to 3 65,0 1 32,5 1 60 1 40 1 14 0,5 up to 245 37/38 4/5 67,5 1 33,7 1 60 1 40 1 14 0,5 up to 255 39/40 6 70,5 1 35,0 1 60 1 40 1

25、14 0,5 up to 265 41/42 7/7,5/8 72,5 1 36,2 1 60 1 40 1 14 0,5 up to 275 43/44 9/10 75,5 1 37,7 1 60 1 40 1 14 0,5 up to 285 45 and over 11 and over 77,5 1 38,5 1 60 1 40 1 14 0,5 5 Sampling and conditioning Test specimens to be tested are taken in accordance with prEN 13400:1998. All test specimens

26、shall be conditioned in accordance with EN 12222 before testing. Minimum time of conditioning 24 hours, and minimum two test pieces by size are necessary. 6 Test method Place the outsole with the heel on a steel base and press the test punch against the outsole unit from the inside at the centre of

27、the heel area at a test rate of 10 mm/min 3mm/min until a force of 5 000 newtons is obtained. 7 Expression of results Plot a load/compression curve (see figure 2) for each test and determine the compression energy E in joules, rounded to the nearest 1 J, from the equation: where F is the applied for

28、ce, in newtons s is the deformation, in metres The result will be expressed as the average value. ds F EPage 6 EN 12743:1999 BSI 08 January 2002 8 Test Report The test report shall include the following information: a) results, expressed in accordance with clause 7; b) full identification of the sam

29、ple; c) reference to this method of test; d) date of testing. Dimensions in mm Figure 1 - Test punch for compression energy testPage 7 EN 12743:1999 BSI 08 January 2002 1 Absorption Energy (S-S): Hysteresis. The difference between S and S. 2 Compression Energy (E): The energy in joules corresponding

30、 to the cycle of the material from 50 N to 5 000 N. 3 Elastic Energy (S): The energy in joules corresponding to the return cycle of the material from 5 000 N to 0 N. Figure 2Page 8 EN 12743:1999 BSI 08 January 2002 Bibliography EN 344, Requirements and test methods for safety, protective and occupat

31、ional footwear for professional use.blankBS EN 12743:1999 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

32、 | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Briti

33、sh Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whi

34、le using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscri

35、bers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Standards are also available from the BSI website at http:/

36、www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international

37、 standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscri

38、bing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information

39、regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications

40、 of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission

41、from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.