BS EN 863-1996 Protective clothing - Mechanical properties - Test method puncture resistance《防护服 机械性能 试验方法 耐穿孔》.pdf

《BS EN 863-1996 Protective clothing - Mechanical properties - Test method puncture resistance《防护服 机械性能 试验方法 耐穿孔》.pdf》由会员分享，可在线阅读，更多相关《BS EN 863-1996 Protective clothing - Mechanical properties - Test method puncture resistance《防护服 机械性能 试验方法 耐穿孔》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 863:1996 Protective clothing Mechanical properties Testmethod: puncture resistance The European Standard EN 863:1995 has the status of British Standard ICS 13.340.10BSEN863:1996 This British Standard, having been prepared under the directionof the Health and Environment Sector

2、 Board, waspublished under the authorityof the Standards Boardand comes into effect on 15March 1996 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference PH/3 Draft for comment 92/46665 DC ISBN 0 580 25310 4 Committees responsible for this British Standard

3、 The preparation of this British Standard was entrusted to Technical Committee PH/3, Protective clothing, upon which the following bodies were represented: British Clothing Industry Association British Safety Industry Federation Health and Safety Executive Industrial Safety (Protective Equipment) Ma

4、nufacturers Association Made-up Textiles Association SATRA Footwear Technology Centre The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Amalgamated Engineering Union Association of Consulting Scientists British Apparel and Textile Confedera

5、tion British Leather Confederation British Marine Industries Federation British Mountaineering Council British Plastics Federation British Textile Technology Group Building Employers Confederation Chartered Institute of Marketing Chemical Industries Association Chief and Assistant Chief Fire Officer

6、s Association Confederation of British Wool Textiles Limited Engineering Equipment and Materials Users Association Ergonomics Society Fabric Care Research Association Ltd. Home Office Institute of Occupational Hygienists Institute of Wastes Management Iron and Steel Trades Confederation London Regio

7、nal Transport Ministry of Defence National Joint Council for the Building Industry (Operatives Side) Textile Distributors Association Trades Union Congress Amendments issued since publication Amd. No. Date CommentsBSEN863:1996 BSI 11-1999 i Contents Page Committees responsible Inside front cover Nat

8、ional foreword ii Foreword 2 Text of EN 863 3BSEN863:1996 ii BSI 11-1999 National foreword This British Standard has been prepared by Technical Committee PH/3and is the English language version of EN863:1995Protective clothing Mechanical properties Test method: puncture resistance, published by the

9、European Committee for Standardization (CEN). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligati

10、ons. Cross-references Publication referred to Corresponding British Standard EN 10002-2:1992 BS EN 10002 Tensile testing of metallic materials BS EN 10002-2:1992 Verification of the force measuring system of the tensile testing machine ISO 2231:1989 BS 3424 Testing coated fabrics Part 2:1992 Method

11、4. Pre-conditioning and conditioning of coated fabrics for testing purposes Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and ma

12、y have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 863 September 1995 ICS 13.340.10 Descriptors: Personal protection equipment, accident prevention, protective clothing, mechanical propertie

13、s, tests, measurements, perforating strength English version Protective clothing Mechanical properties Testmethod: puncture resistance Vtements de protection Proprits mcaniques Mthodedessai:rsistancelaperforation Schutzkleidung Mechanische Eigenschaften Prfverfahren:Widerstandgegen Durchstoen This E

14、uropean Standard was approved by CEN on1995-06-18. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conc

15、erning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own

16、 language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland

17、 and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and it

18、s members Ref. No. EN 863:1995 EEN863:1995 BSI 11-1999 2 Foreword This European Standard was prepared by CEN/TC162,Protective clothing including hand and arm protection and lifejackets, the secretariat of which is held by DIN. This European Standard has been prepared under a Mandate given to CEN by

19、the European Commission and the European Free Trade Association, and supports essential requirements of the EU Directive89/686/EEC. For relationship with EU Directives, seeinformative Annex ZA, which is an integral partof this standard. This European Standard shall be given the status of a national

20、standard, either by publication of an identical text or by endorsement, at the latest by March1996,and conflicting national standards shall be withdrawn at the latest by March1996. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standar

21、d: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, UnitedKingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Test specimens 3 4 Test method 3 4.1 Apparatus 3 4.1.1 Tensile

22、testing machine 3 4.1.2 Test spike 3 4.1.3 Clamps 3 4.2 Conditioning 3 4.3 Procedure 3 5 Calculation of results 3 6 Test report 4 Annex ZA (informative) Clauses of this EuropeanStandard addressing essentialrequirements or other provisions of EU Directives Inside back cover Figure 1 Test spike 4 Figu

23、re 2 Typical clamps arrangement 4EN863:1995 BSI 11-1999 3 1 Scope This European Standard specifies a test method for measuring the puncture resistance of protective clothing or materials used for these products. The puncture resistance is expressed as the maximum force required to push a spike with

24、a specified speed through the test specimens. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated

25、references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10002-2, Metallic materials Tensile testing Part

26、2: Verification of the force measuring system of the tensile testing machines. ISO 2231:1989, Rubber- or plastics-coated fabrics Standard atmospheres for conditioning and testing. 3 Test specimens Take four representative test specimens from the sample, each50mm minimum diameter, so that the specime

27、ns fit between the bolt holes of the clamps. 4 Test method 4.1 Apparatus 4.1.1 Tensile testing machine In this method a tensile testing machine type CRE as defined in EN10002-2is used and shall be capable of: a vertical travel of at least100mm; a constant rate of compression of(100 10)mm/min; a reco

28、rding apparatus for the force and deformation. 4.1.2 Test spike The test spike shall be made of steel, with a minimum hardness of60HRC and shall have the dimensions and the characteristics as shown in Figure 1. The test spike shall be checked by an optical enlargement after every500tests or at least

29、 once a year. When testing materials which wear out the test spike, the optical checks should be done more frequently. If this test shows that the test spike dimensions do not comply with the dimensions of Figure 1, the test spike shall be discarded. NOTEThe control of the dimensions of the test spi

30、ke is important. It is recommended that every test laboratory maintains an internal reference material to do regular checks on the results of the testing. 4.1.3 Clamps The clamping rings have to prevent slippage during the test. They consist of two10mm minimum thick steel plates, each having a (20 0

31、,5)mm diameter hole in the centre and four clamping bolts, as shown in Figure 2. NOTEGripping aids can be used if necessary to prevent slippage or reduce damaging of the specimen. 4.2 Conditioning The specimens shall be conditioned and the test shall be conducted in the standard atmosphere as descri

32、bed in ISO2231,i.e.at a relative humidity of(65 5)%and a temperature of (20 2) C. Conditioning at a specified relative humidity may be omitted if it can be shown that the results for the type of material under test were not affected. 4.3 Procedure Secure the specimen between the clamping rings with

33、the outer surface exposed to the test spike, tighten the nuts sufficiently to ensure no slippage of, or damage to, the specimen. Place the specimen and the clamping rings in the tensile testing machine. Advance the spike on to and through the specimen at a rate of (100 10)mm/min. If the spike fails

34、to penetrate after a movement of25mm after contact with the specimens, the test is terminated. This shall be referred to in the test report. Repeat the procedure on the remaining specimens. Record for each test the maximum force (innewtons) needed to penetrate the specimen. 5 Calculation of results

35、Calculate the arithmetical mean of the maximum force (in newtons) needed to puncture the four test specimens, rounded to the nearest value.EN863:1995 4 BSI 11-1999 6 Test report The test report shall include the following information: the number and the date of this European Standard; all details ne

36、cessary for the identification of the sample tested; the results obtained for each test specimen; the mean value in newtons; any deviation from the procedure outlined in this standard. Dimensions in millimetres Steel 60 HRC Figure 1 Test spike Dimensions in millimetres 1 Specimen *) These figures ar

37、e not critical Figure 2 Typical clamps arrangementEN863:1995 BSI 11-1999 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives This European Standard has been prepared under a Mandate given to CEN by the European Commission an

38、d the European Free Trade Association, and supports essential requirements of the EU Directive89/686/EEC. WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. The clauses of this standard are likely to support requirements

39、 of3.3 of Annex II “Protection against physical injury” of EU Directive89/686/EEC. Compliance with these clauses of this standard provides one means of conforming with the specific essential requirements of the Directive concerned and associated with EFTA requirements.BS EN 863:1996 BSI 389 Chiswick

40、 High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amend

41、ment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard woul

42、d inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of sta

43、ndards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been publi

44、shed as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available wh

45、ich give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefit

46、s contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988

47、 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details suc

48、h as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.