BS EN 3475-416-2005 Cables electrical aircraft use - Test methods - Part 416 Thermal stability《航空器用电缆 试验方法 第416部分 热稳定性》.pdf

《BS EN 3475-416-2005 Cables electrical aircraft use - Test methods - Part 416 Thermal stability《航空器用电缆 试验方法 第416部分 热稳定性》.pdf》由会员分享，可在线阅读，更多相关《BS EN 3475-416-2005 Cables electrical aircraft use - Test methods - Part 416 Thermal stability《航空器用电缆 试验方法 第416部分 热稳定性》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 3475-416:2005 Cables, electrical, aircraft use Test methods Part 416: Thermal stability The European Standard EN 3475-416:2005 has the status of a British Standard ICS 49.060 Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Uncontrolled Copy, (c) BSI

2、BS EN 3475-416:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 10 February 2006 BSI 10 February 2006 ISBN 0 580 47794 0 National foreword This British Standard is the official English language version of EN 3475-416:2005. The UK particip

3、ation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/2, Aerospace Cables, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committe

4、e any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-reference

5、s The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Sta

6、ndards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front co

7、ver, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Uncontr

8、olled Copy, (c) BSIEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN3475416 November2005 ICS49.060 EnglishVersion AerospaceseriesCables,electrical,aircraftuseTest methodsPart416:Thermalstability SriearospatialeCbleslectriquesusage aronautiqueMthodesdessaisPartie416: Vieillissementlachaleur LuftundRa

9、umfahrtElektrischeLeitungenfr LuftfahrtverwendungPrfverfahrenTeil416:Thermische Bestndigkeit ThisEuropeanStandardwasapprovedbyCENon12September2005. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwit

10、houtanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityo

11、faCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherl

12、ands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwide

13、forCENnationalMembers. Ref.No.EN3475416:2005:E Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Uncontrolled Copy, (c) BSIEN 3475-416:2005 2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Preparation of specimens 4 4 Definition of tests5 5 Test program list .6 6 Requiremen

14、t 7 Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Uncontrolled Copy, (c) BSIEN 3475-416:2005 3 Foreword This European Standard (EN 3475-416:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried ou

15、t in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by pu

16、blication of an identical text or by endorsement, at the latest by May 2006, and conflicting national standards shall be withdrawn at the latest by May 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall

17、 not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finlan

18、d, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Uncontrolled Copy, (c) BSI4 1 S

19、cope This product standard defines a test method to evaluate the performance of a coaxial cable after thermal stability. It shall be used together with EN 3475-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references,

20、 only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3475-100, Aerospace series Cables, electrical, aircraft use Test methods Part 100: General. EN 3475-201, Aerospace series Cables, electrical, aircraft use Tes

21、t methods Part 201: Visual examination. EN 3475-302, Aerospace series Cables, electrical, aircraft use Test methods Part 302: Voltage proof test. EN 3475-306, Aerospace series Cables, electrical, aircraft use Test methods Part 306: Continuity of conductors. EN 3475-406, Aerospace series Cables, elec

22、trical, aircraft use Test methods Part 406: Cold bend test. EN 3475-801, Aerospace series Cables, electrical, aircraft use Test methods Part 801: Capacitance per unit length. EN 3475-805, Aerospace series Cables, electrical, aircraft use Test methods Part 805: Characteristic impedance. EN 3475-806,

23、Aerospace series Cables, electrical, aircraft use Test methods Part 806: Attenuation. 3 Preparation of specimens 3.1 Specimen Test is to be performed on four specimens. Length of each specimen: First specimen = 150 nominal overall diameter; Second specimen = 75 nominal overall diameter; Third specim

24、en = as specified in the product norm; Fourth specimen = at least three metres. 3.2 Conditioning The specimen shall not be bent with a radius less than 30 times the overall diameter of the cable, during low or high temperature exposure. EN 3475-416:2005 Licensed Copy: Wang Bin, na, Mon May 08 03:37:

25、01 BST 2006, Uncontrolled Copy, (c) BSI5 4 Definition of tests 4.1 Visual examination (EN 3475-201) 4.2 Voltage proof test (EN 3475-302) 4.3 Continuity of conductors (EN 3475-306) 4.4 Capacitance per unit of length (EN 3475-801) 4.5 Attenuation at 200 MHz (EN 3475-806) 4.6 Characteristic impedance (

26、EN 3475-805 Method B) 4.7 Cold bend test (EN 3475-406) Maintain the specimen at the temperature specified in the test method (EN 3475-406) but for 16 hours. During the conditioning period, the specimen shall be kept reasonably straight with a weight specified in the product standard. After the condi

27、tioning period, and while the specimen is still at the test temperature, the specimen shall be wrapped around the mandrel (diameter of mandrel defined in product standard) for three full turns. The mandrel shall be turned at a maximum uniform rate of one revolution per four seconds. 4.8 Dynamic wind

28、ing The entire specimen is wound round a mandrel with a diameter of 15 times the overall nominal diameter of the cable. The specimen is then totally unwound. Duration of a cycle: (30 5) s. Number of cycles: 10. 4.9 Shrinkage measurement Measurement of the distance between inner conductor and dielect

29、ric. 4.10 Heat exposure Specimens are placed in a heat chamber for seven days at the temperature specified in the product norm. After the heat exposure period, remove the specimen from the heat chamber and condition it at room ambient temperature for 24 hours. EN 3475-416:2005 Licensed Copy: Wang Bi

30、n, na, Mon May 08 03:37:01 BST 2006, Uncontrolled Copy, (c) BSI6 4.11 Bend test (without ageing) Fix one of the specimen to the mandrel (diameter given in product standard) in such a way that the performance of the cable is unaffected. Turn the mandrel at between two and three turns until 90 % of th

31、e total length is wound round the mandrel whilst ensuring that the bent portion of the cable maintains contact with the mandrel throughout its length. If a load is used to ensure contact with the mandrel then it shall not exceed that given in the product standard. Whilst the cable is still wrapped a

32、round the mandrel repeat the measurement of the impedance of the sample. 5 Test program list 5.1 On first specimen initial shrinkage measurement; heat exposure; final shrinkage measurement; visual examination; cold bend test; visual examination; voltage proof test; continuity of conductors. 5.2 On s

33、econd specimen initial shrinkage measurement; heat exposure; final shrinkage measurement; visual examination; dynamic winding; visual examination; final shrinkage measurement; voltage proof test; continuity of conductors. EN 3475-416:2005 Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Un

34、controlled Copy, (c) BSI7 5.3 On third specimen capacitance; transmission loss; heat exposure; capacitance; transmission loss; capacitance variation; transmission variation. 5.4 On fourth specimen initial impedance measurement; bend test; final impedance measurement. 6 Requirement 6.1 On first and s

35、econd specimens manufacturer marking must be legible. neither splits, nor cracks, shall be observed on jacket material. maximum shrinkage at either end shall be less than the value required in the product standard. no breakdown, no discontinuity of conductors. 6.2 On third specimen maximum change of

36、 capacitance per unit of length (EN 3475-801): as specified in the product standard. maximum increase of attenuation at 200 MHz (EN 3475-806): as specified in the product standard. 6.3 On fourth specimen maximum change of impedance shall not be greater than that allowed in the product standard. EN 3

37、475-416:2005 Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Uncontrolled Copy, (c) BSIBS EN 3475-416:2005 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view o

38、n standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the q

39、uality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44

40、 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:

41、+44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless o

42、therwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its produc

43、ts and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefi

44、ts contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:

45、/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system

46、or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these

47、 details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-. Licensed Copy: Wang Bin, na, Mon May 08 03:37:01 BST 2006, Uncontrolled Copy, (c) BSI