BS EN 2240-005-2009 Aerospace series - Lamps incandescent - Lamp code 73 - Product standard《航空航天系列 白炽灯 灯、代码73 产品标准》.pdf

《BS EN 2240-005-2009 Aerospace series - Lamps incandescent - Lamp code 73 - Product standard《航空航天系列 白炽灯 灯、代码73 产品标准》.pdf》由会员分享，可在线阅读，更多相关《BS EN 2240-005-2009 Aerospace series - Lamps incandescent - Lamp code 73 - Product standard《航空航天系列 白炽灯 灯、代码73 产品标准》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN2240-005:2009ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Lamps, incandescentPart 005: Lamp, code 73 ProductstandardThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 Decemb

2、er2009 BSI 2009ISBN 978 0 580 68635 1Amendments/corrigenda issued since publicationDate CommentsBS EN 2240-005:2009National forewordThis British Standard is the UK implementation of EN 2240-005:2009.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic

3、electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British St

4、andard cannot confer immunityfrom legal obligations.BS EN 2240-005:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2240-005 December 2009 ICS 49.060 English Version Aerospace series - Lamps, incandescent - Part 005: Lamp, code 73 - Product standard Srie arospatiale - Lampes incandescence -

5、Partie 005 : Lampe, code 73 - Norme de produit Luft- und Raumfahrt - Glhlampen - Teil 005: Lampe, Kode 73 - Produktnorm This European Standard was approved by CEN on 7 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

6、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official version

7、s (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, B

8、ulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STAND

9、ARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2240-005:2009: EBS EN 2240-005:2009EN 2240-005:2009

10、(E) 2 Contents Foreword 31 Scope 42 Normative references 43 Required characteristics .43.1 Dimensions and mass .43.2 Other characteristics .53.3 Form of filament .53.4 Cap 54 Designation 55 Marking .56 Technical specification .5BS EN 2240-005:2009EN 2240-005:2009 (E) 3 Foreword This document (EN 224

11、0-005:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Serv

12、ices of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the lates

13、t by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standa

14、rds organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Por

15、tugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2240-005:2009EN 2240-005:2009 (E) 4 1 Scope This European Standard specifies the required characteristics for lamp, code 73, for aerospace applications. It shall be used together with EN 2756. 2 Normative re

16、ferences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2240-001, Aerospace series Lamps, inc

17、andescent Part 001: Technical specification EN 2240-002, Aerospace series Lamps, incandescent Part 002: Main characteristics EN 2241, Aerospace series Lamp base Dimensions1)EN 2756, Aerospace series Lamps, incandescent Test methods 3 Required characteristics 3.1 Dimensions and mass See Figure 1 and

18、Table 1. Dimensions are given in millimetres. Table 1 Key 1 Light centre Figure 1 Bulb appearance Clear Nominal voltage V 28 Nominal current A 0,02 Nominal power W 0,56 Nominal luminous flux lm 1 Colour temperature K 1 960 LifeStatic with d.c. h 1 000 Dynamic with d.c. h 750 Static with a.c. h 2 500

19、 Reduced voltage V Luminous flux at reduced voltage lm Form of filament CC - 2F Light Centre Length (LCL) 8 1 Mass (for 1 000) kg 0,4 1) Published as ASD-STAN Prestandard at the date of publication of this standard. BS EN 2240-005:2009EN 2240-005:2009 (E) 5 3.2 Other characteristics See Table 1. 3.3

20、 Form of filament See EN 2240-002. 3.4 Cap SY4s/7: see EN 2241. 4 Designation EXAMPLE Description block LAMP, INCANDESCENT Identity block EN2240-73 Number of the basic standard Code (see EN 2240-002) NOTE If necessary, the code I9005 should be placed between the description block and the identity bl

21、ock. 5 Marking Unless there is not enough space, the lamp and its packaging shall be marked with the international code number such as indicated in EN 2240-002. 6 Technical specification See EN 2240-001. BS EN2240-005:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 89

22、96 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amend

23、ment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would i

24、nform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest edit

25、ions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ respons

26、e to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Li

27、brary and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with

28、 standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standard

29、sOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs

30、 and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of neces

31、sary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: