BS 6F 37-1990 Specification for 570 g m2 and 640 g m2 cotton canvas fabrics for aerospace purposes《航空航天用570g m m和 640g m m棉粗帆布纤维规范》.pdf

《BS 6F 37-1990 Specification for 570 g m2 and 640 g m2 cotton canvas fabrics for aerospace purposes《航空航天用570g m m和 640g m m棉粗帆布纤维规范》.pdf》由会员分享，可在线阅读，更多相关《BS 6F 37-1990 Specification for 570 g m2 and 640 g m2 cotton canvas fabrics for aerospace purposes《航空航天用570g m m和 640g m m棉粗帆布纤维规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS6F37:1990 (Superseding BS5F37:1981) Specification for 570g/m 2and640g/m 2cotton canvas fabrics for aerospace purposesBS6F37:1990 This BritishStandard, having been prepared under the directionof the Aerospace Standards Policy Committee (ACE/-), was published undert

2、heauthority of the Board of BSIand comes into effect on 31October1990 BSI02-2000 The following BSI references relate to the work on this standard: Committee reference ACE/54 Draft for comment88/74833 DC ISBN 0 580 17804 8 Committees responsible for this BritishStandard The preparation of this Britis

3、hStandard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/54, upon which the following bodies were represented: British Fabric Association British Rubber Manufacturers Association British Textile Employers Association Man-made Fibres Producers Committee M

4、inistry of Defence Society of British Aerospace Companies Limited Society of Dyers and Colourists Amendments issued since publication Amd. No. Date of issue CommentsBS6F37:1990 BSI 02-2000 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 General requirements 1 3 Yarn

5、 type 1 4 Manufacture 1 5 Finish 1 6 Construction and properties of finished fabric 2 7 Identification 2 Appendix A Information to be supplied by the purchaser 3 Table 1 General requirements 1 Table 2 Properties of the yarn 1 Table 3 Properties of the loom state fabrics 1 Publications referred to In

6、side back coverBS6F37:1990 ii BSI 02-2000 Foreword This BritishStandard, prepared under the direction of the Aerospace Standards Policy Committee, is one of a series for textiles of a quality suitable for aerospace purposes and is a revision of BS5F37, which is withdrawn. It differs from the previou

7、s edition primarily in that provision for the supply of fabrics treated with mineral khaki has been deleted. Quality requirements as defined in the latest edition of BSF100 are also included, as are details of information to be supplied by the purchaser. WARNING NOTES 1) This standard calls for the

8、use of substances and/or test procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and in no way absolves either the supplier or the user from statutory obligations relating to health and safety at any stage of manufacture or use.

9、2) This standard specifies pentachlorophenyl laurate (PCPL) as the only approved rot-proofing treatment for aerospace fabrics. Alternative treatments are under development, and this standard will be updated to delete PCPL assoon as an approved alternative treatment for aerospace fabrics is available

10、. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprise

11、s a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS6F37:1990 BSI 02-2000 1 1 S

12、cope This BritishStandard specifies the requirements for cotton canvas fabrics of nominal loomstate mass570g/m 2and640g/m 2for aerospace purposes, primarily for heavy duty parachute packs. NOTE 1The information to be supplied by the purchaser in the contract or order is listed in Appendix A. NOTE 2T

13、he publications referred to in this standard are listed on the inside back cover. NOTE 3The latest revision of an Aerospace Series Standard is indicated by a prefix number. 2 General requirements 2.1 In addition to the requirements specified in clauses2 to7, the following sections and clauses of the

14、 latest edition of BSF100 shall apply (seeTable 1). 2.2 Fabrics treated with pentachlorophenyl laurate (PCPL), shall meet the requirements of BS2087-1 freedom from impurities clause. 3 Yarn type 3.1 The fabrics shall be manufactured from unsized cotton yarn free from trash and seed coat. 3.2 The yar

15、n shall comply with the requirements given in Table 2. 4 Manufacture 4.1 The weave shall be plain. 4.2 The fabric shall be supplied either: a) without identification markers; or b) where requested by the purchaser (seeAppendix A), marked with a coloured thread woven into the fabric3cm from each selv

16、edge. For fabric429 the thread shall be blue and for fabric37 the thread shall be red. Table 1 General requirements (giveninBSF100) 4.3 The loomstate properties of the fabrics shall comply with the requirements given in Table 3. 5 Finish 5.1 General The fabrics shall be supplied scoured and either:

17、a) undyed and rot-proofed (see5.4); or b) dyed (see5.3) and rot-proofed (see5.4); or c) dyed (see5.3), rot-proofed (see5.4) and rendered water repellent (see5.5). 5.2 Undyed fabrics Undyed fabrics shall not be bleached or given a whitening treatment. Table 2 Properties of the yarn Table 3 Properties

18、 of the loom state fabrics Section Title Requirements and tests 1 General All requirements 2 Quality requirements Requirements for the manufacture of wide fabrics Requirements for dyed textiles Requirements for dimensions and tolerances: general and wide fabrics Requirements for freedom from defects

19、 3 Physical tests Test for the determination of mass of wide fabric Tests for breaking strength and extension under load of wide fabrics Test for water repellency Fabric designation Yarn linear density Plies Folding twist Twist direction Warp Weft Warp Weft Warp Weft 429 37 dtex 500 500 dtex 500 500

20、 3 4 4 4 turns/m 355 240 turns/m 240 240 S S Fabric designation Minimum number of threads per centimetre a Mass per unit area Minimum average breaking strength Warp Weft Warp Weft 429 37 17.3 15.7 11.4 11.8 g/m 2 570 20 640 20 N/50mm 1600 1800 N/50mm 1600 1800 a Calculated from the number of threads

21、 in a measured length of not less than2cm.BS6F37:1990 2 BSI 02-2000 5.3 Dyeing Where dyeing is required, the colour shall be specified either by reference to a BritishStandard, e.g.BS381C, or otherwise by pattern. NOTEThe requirement for dyed fabric and the colour should be stated in the contract or

22、 order (see Appendix A). 5.4 Rot-proofing The fabrics shall be treated with pentachlorophenyl laurate (PCPL) in accordance with BS2087-1: normal process. No alternative process shall be permitted. 5.5 Water repellent treatment 5.5.1 Where requested by the purchaser (seeAppendix A), the fabric shall

23、be rendered permanently water repellent by a process which complies with6.3. 5.5.2 Water repellent treatments known to accelerate actinic damage shall not be used. 6 Construction and properties of finished fabric NOTEThe minimum usable width of the finished fabric should be as stated by the purchase

24、r in the contract or order (seeAppendix A), but a minimum usable width of900mm is usually supplied. 6.1 Tests When tested in accordance with clause2, the fabric in the finished state shall comply with6.2 and6.3. 6.2 Breaking strength The minimum average breaking strength in both warp and weft direct

25、ions shall be not less than the following: 6.3 Water repellency Where required, the fabric shall be rendered water repellent such that the mean absorption shall not exceed25% and the penetration shall be nil, i.e.no individual figure shall exceed nil. 7 Identification The fabric shall be identified

26、for ordering purposes by the number and date of this BritishStandard, i.e.BS6F37:1990 1)together with the relevant designation given in Table 2 and, if required, the colour and water repellent treatment. NOTEThis identification may be codified. For example, fabric429 required dyed to BS381C Olive dr

27、ab and water repellent, may be identified as BS6F37/429/BS381C No.298/WR. a) fabric designation429: 1400N/50mm b) fabric designation37: 1600N/50mm 1) Marking BS6F37:1990 on or in relation to a product represents a manufacturers declaration of conformity, i.e.a claim by or on behalf of the manufactur

28、er that the product meets the requirements of the standard. The accuracy of the claim is therefore solely the responsibility of the person making the claim. Such a declaration is not to be confused with third party certification of conformity, which may also be desirable.BS6F37:1990 BSI 02-2000 3 Ap

29、pendix A Information to be supplied by the purchaser The following information should be stated by the purchaser in the contract or order: a) the number of this BritishStandard, i.e.BS6F37; b) the fabric designation, selected from Table 2; c) whether identification markers are required (see4.2); d)

30、if required dyed, the colour (see5.3); e) whether water repellent treatment is required (see5.5); f) the minimum usable width required (seeclause6).4 blankBS6F37:1990 BSI 02-2000 Publications referred to BSF100, Procedure for inspection and testing of textiles for aerospace purposes. BS381C, Specifi

31、cation for colours for identification, coding and special purposes. BS2087, Preservative treatments for textiles. BS2087-1, Specification for treatments. BS6F37:1990 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing

32、 BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It i

33、s the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front

34、cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to C

35、ustomer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of informatio

36、n on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. S

37、ubscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publica

38、tions. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, pho

39、tocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.