ASTM F2632-2007(2013)e1 Standard Practice for Determining the Toner Usage for Color Printer Cartridges《测定彩色打印机硒鼓中调色剂使用率的标准实施规程》.pdf

《ASTM F2632-2007(2013)e1 Standard Practice for Determining the Toner Usage for Color Printer Cartridges《测定彩色打印机硒鼓中调色剂使用率的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2632-2007(2013)e1 Standard Practice for Determining the Toner Usage for Color Printer Cartridges《测定彩色打印机硒鼓中调色剂使用率的标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2632 07 (Reapproved 2013)1Standard Practice forDetermining the Toner Usage for Color Printer Cartridges1This standard is issued under the fixed designation F2632; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the ye

2、ar of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTERevised the units presentation and added a units statement editorially in April 2013.1. Scope1.1 This practice describe

3、s the procedure to determine theweight of toner used for printing a single page using anelectrophotographic color printing process. This practice uses asolid area 5 % page coverage target for each color. Thispractice requires specific tools and skills for disassembling andreassembling printer cartri

4、dges.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns, if any,

5、 associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2F1206 Test Method for Evaluating Color Image Output

6、fromColor Printers and CopiersF1856 Practice for Determining Toner Usage for PrinterCartridges3. Summary of Practice3.1 An electrophotographic printer using color toner supplycartridges or all-in-one toner cartridges is set up to determinethe toner usage for a single page. A test target page with 5

7、%solid area of each toner cartridge color is used. 5 % coverageof the printable area for each color is the accepted average pagecoverage for office printers. Office color printers are used toproduce color graphic images and photographs along with text.3.2 The all-in-one toner cartridges are disassem

8、bled toseparate the toner hopper from the waste toner collection bin.The weight of the full toner hopper is measured. A specifiednumber of 5 % coverage prints are created at specific testintervals. The weight of each hopper is measured at thebeginning and end of each test interval. The toner used fo

9、r onepage is calculated. The results can be used to estimate the totalpage yield of the color toner cartridge. A comparison can bemade between the toner usage for the control cartridges andany other cartridges tested.3.3 Print quality, print density, and color measurement testtargets can be printed

10、only when the specified 5 % coveragetest intervals are not being printed.4. Significance and Use4.1 This practice can be used for the evaluation of new andremanufactured color toner cartridges and their respectivecomponents used in an electrophotographic process.4.2 This practice is suitable for res

11、earch and developmentand for quality acceptance evaluations.5. Interferences5.1 Relative humidity can impact test results. The testsshould be performed at a controlled temperature and humiditywithin the operating humidity range of the printer. This isusually between 20 % and 80 % relative humidity (

12、RH). Allequipment and materials should be conditioned in the sametemperature and relative humidity for at least 24 h prior totesting.5.2 In a comparative cartridge test, the same test target(data) and the same printer must be used. Same model printerscan have significant toner usage variations under

13、 the sameenvironmental conditions.5.3 The test target should not produce uneven wear on thecartridge components as this will affect the test results. Adjustthe location of the printed areas to create an even distribution.5.4 The software used to make the test target should causethe printer to print

14、the pure color from each color cartridge.This ensures that only toner from one cartridge is used toproduce the color on the test target.1This practice is under the jurisdiction of ASTM Committee F05 on BusinessImaging Products and is the direct responsibility of Subcommittee F05.04 onElectrostatic I

15、maging Products.Current edition approved April 1, 2013. Published April 2013. Originallyapproved in 2007. Last previous edition approved in 2007 as F263207. DOI:10.1520/F2632-07R13E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm

16、.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.5 Printer related items such as the power supply, densitycont

17、rol settings, resolution enhancements, toner saver settings,economy mode settings, color calibration, and laser optics mayimpact image quality and toner usage.5.6 Test printers should be in good mechanical and electri-cal condition. Preferably, printers with a continuous history ofpreventative maint

18、enance should be used. Printer failures caninvalidate the test.5.7 A calibrated balance must be used to obtain the weightsof the toner hopper.5.8 The techniques used for cartridge disassembly shouldavoid toner spillage and ensure accurate toner weight measure-ments.6. Equipment and Materials6.1 Elec

19、trophotographic test printer, suitable for testingpurposes.6.2 Printer data system, capable of supplying 5 % pagecoverage of the printable area for each color cartridge. Theprintable area is 8 by 10 in. (203 by 254 mm), making it usablefor standard letter and A4 paper sizes. This 5 % test target dat

20、acan be created using available software.6.2.1 The 5 % test target has eight color bands made up oftwo sets of four color bands. Each band has an area of 2.5 % ofthe printable area. The eight color bands on the target arearranged in the following order from top to bottom: magenta,yellow, cyan, black

21、, magenta, yellow, cyan, and black.6.2.2 The portrait target is used for printers processing themedia with the short edge perpendicular to the direction ofpaper movement. This target layout is shown in Fig. 1.6.2.3 Color bands for the portrait target are 8.00 in. (203.20mm) in length and 0.25 in. (6

22、.35 mm) in width.6.2.4 For the portrait target, the color bands are placedhorizontal on the page separated by 1.25 in. (31.75 mm)center-to-center.6.2.5 The landscape target is used for printers processing themedia with the long edge perpendicular to the direction ofpaper movement. This target layout

23、 is shown in Fig. 2.6.2.6 Color bands for the landscape target are 10.00 in.(254.00 mm) in length and 0.20 in. (5.08 mm) in width.6.2.7 For the landscape target, the color bands are placedhorizontal on the page separated by 1.00 in. (25.40 mm)center-to-center.6.3 Control and Test cartridges designed

24、 for use in the testprinter.6.4 Balance capable of measuring the cartridge toner hopperwith a precision of 60.1 g and readability of 0.1 g.6.5 Conditioned Paper that meets the requirements of theprinter. This same paper type and manufacturer should be usedfor all comparative tests.6.6 Hygrometer and

25、 Thermometer.6.7 Special tools and instructions for disassembling andreassembling the printer cartridge.7. Test Procedure7.1 Set up the test printer. Set the printer to the “factorydefault” print mode. Do not use the “toner saver mode.” Setand record the printer attributes that can affect the print

26、quality.The attributes may include: density, resolution, resolutionenhancement, color, and so forth. Use separate, known goodcartridges to verify that the printer is working properly. Checkthat the 5 % test target source is operating correctly.7.2 Measure and record the temperature and humidity in t

27、hetest area.7.3 Select the color cartridges to be tested. Remove the seal,if any. Separate the hoppers from the waste bins and measurethe full hopper weight in grams.7.4 Run the cartridges according to 7.5 using the 5 %coverage color test target. When the test intervals are notrequired, other test t

28、argets can be used for determining printdensity, print quality, and color measurement tests.7.5 During the running of the cartridges, weights are deter-mined at the beginning and end of 1, 2, or 3 intervals of 1000pages each. While the test intervals are printing, only the 5 %FIG. 1 Test Target Layo

29、utPortraitFIG. 2 Test Target LayoutLandscapeF2632 07 (2013)12page coverage target can be used. For the expected life of thecartridge, the start and end page counts are listed in Table 1.7.6 If a cartridge has run out of toner while the othercartridges are still running, replace the empty cartridge w

30、ithanother usable cartridge. Note the page count. Do not measureweights for the replacement cartridge. The test ends when allstarting cartridges have completed the last required test inter-val.7.7 At the end of the test, clean the toner hoppers andmeasure the empty weight. The toner available can be

31、 calcu-lated from these weights and the weights measured in 7.3.8. Calculation8.1 Calculate and record the weights of toner used duringeach test interval. The toner used is the weight differencebetween the start and end weights of the 5 % coverage testintervals.8.2 Toner usage (mg/page) is the weigh

32、t of toner (g) usedduring the 1000 page interval. The grams of toner used for1000 pages is the same as the milligrams of toner for one page.9. Report9.1 Report test conditions (temperature and humidity), mea-sured weights with page counts, cartridge identification, printersetup conditions, printer i

33、dentification, test target dataidentification, and the toner usage for each color cartridge.10. Interpretation of Results10.1 The toner usage determined by this practice relatesonly to the conditions used. It is useful in making directcomparisons between cartridges.10.2 The average page yield for th

34、e cartridge can beestimated by dividing the total weight of the available toner bythe average toner usage. The available toner is determined bycalculating the difference between the initial toner weight andthe remaining toner weight at end of usable printing.10.3 Practice F1856 can be used to determ

35、ine the tonerusage for text only.10.4 Test Method F1206 can be used to measure the colorfrom specific targets run between the test intervals described inSection 7.11. Keywords11.1 cartridge; color printer; color toner; electrophoto-graphic; laser printer; non-impact printer; page yield; tonerusageAS

36、TM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are e

37、ntirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards

38、and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee

39、 on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or

40、 at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Test Intervals for Color Toner CartridgesExpectedPagesTest Int

41、erval 1 Test Interval 2 Test Interval 3Start End Start End Start End1000 0 10002000 500 15003000 500 15004000 500 1500 2000 30005000 1000 2000 3000 40006000 1000 2000 3000 40007000 2000 3000 4000 50008000 2000 3000 4000 5000 6000 70009000 2000 3000 4000 5000 6000 700010 000 2000 3000 4000 5000 6000 700011 000 2000 3000 5000 6000 7000 800012 000 3000 4000 6000 7000 8000 900013 000 3000 4000 6000 7000 9000 10 00014 000 3000 4000 6000 7000 9000 10 00015 000 4000 5000 7000 8000 10 000 12 00016 000 4000 5000 7000 8000 10 000 12 000F2632 07 (2013)13