ASTM F1301-1990(2011)e1 Standard Practice for Labeling Chemical Protective Clothing《标记化工防护服的标准操作规程》.pdf

《ASTM F1301-1990(2011)e1 Standard Practice for Labeling Chemical Protective Clothing《标记化工防护服的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1301-1990(2011)e1 Standard Practice for Labeling Chemical Protective Clothing《标记化工防护服的标准操作规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F1301 90 (Reapproved 2011)1Standard Practice forLabeling Chemical Protective Clothing1This standard is issued under the fixed designation F1301; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision

2、. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorially revised referenced document in 2.1 and 4.2.3 in February 2011.INTRODUCTIONThis practice is intended to provide guidance on the

3、 minimum label information for chemicalprotective clothing.1. Scope1.1 This practice covers the informational content of labelsin or on chemical protective clothing.1.2 This practice details the recommended format andminimal content of the information to be included on the labelsused for chemical pr

4、otective clothing.1.3 Protective clothing is defined as any single item orcombination of items used for the purpose of isolating parts ofthe body from direct contact with a potential hazard. It does notinclude individual parts of a protective clothing item designedto be worn as part of another item

5、(for example, a faceshield orlens) unless it may be worn independently of the other itemsand still be used in a protective manner. For example, a gloveor boot unless permanently attached would be considered aprotective clothing item requiring labeling, while a visor orvent valve would not. In summar

6、y, the intent of this practice isto only require labeling of parts of an ensemble that can beused independently for the protection of the user.1.4 This practice does not cover user information providedby means other than item labeling such as instructions,informational packets, brochures, or other w

7、ritten means.1.5 This practice excludes those items covered under 16CFR 303 unless specifically designed for use as chemicalprotective clothing.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standa

8、rd to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ANSI Standards:ANSI/ISEA 101-1996 (2008) Standard for Limited-Use andDisposable CoverallsSize and Labeling Requirements22.2 Code of Federal Regu

9、lation:16 CFR 303 Textile Fiber Products Identification Act33. Significance and Use3.1 GeneralThis practice contains the recommendationsfor minimal informational requirements for the identification ofchemical protective clothing items. It is intended to provide theuser with some of the basic informa

10、tion necessary for theproper selection and use of the chemical protective clothingwhen comparing resistance data derived from ASTM perfor-mance testing.4. Minimal Informational Requirements4.1 The minimum informational requirements for labelingof chemical protective clothing include an identificatio

11、n of theitem, the manufacturers or distributors name, base composi-tion information (material of construction), and size.4.2 The following details the minimum requirements:4.2.1 IdentificationThe name or trade name, or otherdescriptions for the item (such as catalog number, etc.).4.2.2 Manufacturers

12、 or Distributors NameThe name ofthe manufacturer or distributor of the item.4.2.3 Base Composition and SizeThe barrier compositionof the garment or item (it is suggested that the generic orcommon terms for base composition be provided) and manu-facturers size designation. If of multilayered construc

13、tion, the1This practice is under the jurisdiction of ASTM Committee F23 on PersonalProtective Clothing and Equipment and is the direct responsibility of SubcommitteeF23.30 on Chemicals.Current edition approved Feb. 1, 2011. Published March 2011. Originallyapproved in 1990. Last previous edition appr

14、oved in 2006 as F1301 - 90(2006).DOI: 10.1520/F1301-90R11E01.2Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.3Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: S

15、DE, Washington, DC 20401, http:/www.access.gpo.gov.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.largest percentage of barrier composition or trade name for thecomplete composition can be shown. However, it is suggestedthat all com

16、position elements be noted. The sizing should bethe manufacturers size designation in either a category (forexample, Large) or inch-pound or SI (metric) units (forexample, 42 to 44 in./107 to 112 cm). Width and girthmeasurements are also of value but optional. ANSI/ISEA 101-1996 (2008) is one standa

17、rd for sizing that could be followed.5. Label Format5.1 The manufacturer or distributor may utilize any form ortype of labeling method to convey the required information.This may take the form of silk screen impressions, tags, or anyother means of labeling. Integral or attached labels are recom-mend

18、ed.5.2 The label should be of a durable nature such that theexpected life of the label is the same as the garment orprotective clothing item, where possible.5.3 The size of the label should be sufficient to enable theuser to easily read the information provided. It should also belocated on the item

19、in a location to facilitate recognition.5.4 Labeling of chemical protective clothing containers orpackages only does not constitute labeling as defined in thispractice.5.5 Each piece that could be worn independently for theprotection of the user, must be labeled (for example, hoods,overgarments, glo

20、ves, boots, etc.).5.6 The appendix shows an example of a label that followsthis practice.6. Keywords6.1 chemical protective clothing; labeling; protectiveclothingAPPENDIX(Nonmandatory Information)X1. EXAMPLE LABELASTM International takes no position respecting the validity of any patent rights asser

21、ted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by

22、the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receiv

23、e careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Intern

24、ational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. X1.1 Example LabelF1301 90 (2011)12