ASTM D7566-2018 red 8125 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons《含合成碳氢化合物的航空涡轮燃料标准规范》.pdf

《ASTM D7566-2018 red 8125 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons《含合成碳氢化合物的航空涡轮燃料标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7566-2018 red 8125 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons《含合成碳氢化合物的航空涡轮燃料标准规范》.pdf（43页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7566 17bD7566 18 An American National StandardStandard Specification forAviation Turbine Fuel Containing SynthesizedHydrocarbons1This standard is issued under the fixed designation D7566; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、 case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1

3、This specification covers the manufacture of aviation turbine fuel that consists of conventional and synthetic blendingcomponents.1.2 This specification applies only at the point of batch origination, as follows:1.2.1 Aviation turbine fuel manufactured, certified, and released to all the requirement

4、s of Table 1 of this specification (D7566),meets the requirements of Specification D1655 and shall be regarded as Specification D1655 turbine fuel. Duplicate testing is notnecessary; the same data may be used for both D7566 and D1655 compliance. Once the fuel is released to this specification(D7566)

5、 the unique requirements of this specification are no longer applicable: any recertification shall be done in accordance withTable 1 of Specification D1655.1.2.2 Field blending of synthesized paraffinic kerosine (SPK) blendstocks, as described in Annex A1 (FT SPK), Annex A2(HEFA SPK), Annex A3 (SIP)

6、, synthesizedAnnex A4 paraffinic kerosine plus aromatics (SPK/A) as described in synthesizedparaffinic kerosine plus aromatics (SPK/A), Annex A4, or Annex A5 (ATJ) with D1655 fuel (which may on the whole or in parthave originated as D7566 fuel) shall be considered batch origination in which case all

7、 of the requirements of Table 1 of thisspecification (D7566) apply and shall be evaluated. Short form conformance test programs commonly used to ensure transportationquality are not sufficient. The fuel shall be regarded as D1655 turbine fuel after certification and release as described in 1.2.1.1.2

8、.3 Once a fuel is redesignated as D1655 aviation turbine fuel, it can be handled in the same fashion as the equivalent refinedD1655 aviation turbine fuel.1.3 This specification defines the minimum property requirements for aviation turbine fuel that contain synthesizedhydrocarbons and lists acceptab

9、le additives for use in civil operated engines and aircrafts. Specification D7566 is directed at civilapplications, and maintained as such, but may be adopted for military, government, or other specialized uses.1.4 This specification can be used as a standard in describing the quality of aviation tu

10、rbine fuel from production to the aircraft.However, this specification does not define the quality assurance testing and procedures necessary to ensure that fuel in thedistribution system continues to comply with this specification after batch certification. Such procedures are defined elsewhere, fo

11、rexample in ICAO 9977, EI/JIG Standard 1530, JIG 1, JIG 2, API 1543, API 1595, and ATA-103.1.5 This specification does not include all fuels satisfactory for aviation turbine engines. Certain equipment or conditions of usemay permit a wider, or require a narrower, range of characteristics than is sh

12、own by this specification.1.6 While aviation turbine fuels defined by Table 1 of this specification can be used in applications other than aviation turbineengines, requirements for such other applications have not been considered in the development of this specification.1.7 Synthetic blending compon

13、ents, synthetic fuels, and blends of synthetic fuels with conventional petroleum-derived fuels inthis specification have been evaluated and approved in accordance with the principles established in Practice D4054.1.8 The values stated in SI units are to be regarded as standard. No other units of mea

14、surement are included in this standard.1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability

15、ofregulatory limitations prior to use.1 This specification is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of SubcommitteeD02.J0.06 on Emerging Turbine Fuels.Current edition approved Dec. 1, 2017April 1, 2018. Publis

16、hed March 2018April 2018. Originally approved in 2009. Last previous edition approved in 2017 asD7566 17a.D7566 17b. DOI: 10.1520/D7566-17B.10.1520/D7566-18.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made

17、 to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Su

18、mmary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States11.10 This international standard was developed in accordance with internationally recognized principles on standardizationesta

19、blished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D56 Test Method for Flash Point by Tag Closed Cup TesterD86 Te

20、st Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric PressureD93 Test Methods for Flash Point by Pensky-Martens Closed Cup TesterD129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method)D130 Test Method for Corrosiveness to Copp

21、er from Petroleum Products by Copper Strip TestD156 Test Method for Saybolt Color of Petroleum Products (Saybolt Chromometer Method)D240 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb CalorimeterD323 Test Method for Vapor Pressure of Petroleum Products (Reid Method)D381 Test

22、Method for Gum Content in Fuels by Jet EvaporationD445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)D1266 Test Method for Sulfur in Petroleum Products (Lamp Method)D1298 Test Method for Density, Relative Density, or API Gravity of Crude

23、Petroleum and Liquid Petroleum Products byHydrometer MethodD1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator AdsorptionD1322 Test Method for Smoke Point of Kerosene and Aviation Turbine FuelD1405 Test Method for Estimation of Net Heat of Combustion of Avia

24、tion FuelsD1655 Specification for Aviation Turbine FuelsD1840 Test Method for Naphthalene Hydrocarbons in Aviation Turbine Fuels by Ultraviolet SpectrophotometryD2276 Test Method for Particulate Contaminant in Aviation Fuel by Line SamplingD2386 Test Method for Freezing Point of Aviation FuelsD2425

25、Test Method for Hydrocarbon Types in Middle Distillates by Mass SpectrometryD2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence SpectrometryD2624 Test Methods for Electrical Conductivity of Aviation and Distillate FuelsD2710 Test Method for Bromine Index of

26、 Petroleum Hydrocarbons by Electrometric TitrationD2887 Test Method for Boiling Range Distribution of Petroleum Fractions by Gas ChromatographyD2892 Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column)D3227 Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Avia

27、tion Turbine, and Distillate Fuels (PotentiometricMethod)D3240 Test Method for Undissolved Water In Aviation Turbine FuelsD3241 Test Method for Thermal Oxidation Stability of Aviation Turbine FuelsD3242 Test Method for Acidity in Aviation Turbine FuelD3338 Test Method for Estimation of Net Heat of C

28、ombustion of Aviation FuelsD3343 Test Method for Estimation of Hydrogen Content of Aviation FuelsD3701 Test Method for Hydrogen Content of Aviation Turbine Fuels by Low Resolution Nuclear Magnetic ResonanceSpectrometryD3828 Test Methods for Flash Point by Small Scale Closed Cup TesterD3948 Test Meth

29、od for Determining Water Separation Characteristics of Aviation Turbine Fuels by Portable SeparometerD4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density MeterD4054 Practice for Evaluation of New Aviation Turbine Fuels and Fuel AdditivesD4057 Practice for Ma

30、nual Sampling of Petroleum and Petroleum ProductsD4171 Specification for Fuel System Icing InhibitorsD4176 Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)D4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive

31、X-ray Fluorescence SpectrometryD4306 Practice for Aviation Fuel Sample Containers for Tests Affected by Trace ContaminationD4529 Test Method for Estimation of Net Heat of Combustion of Aviation FuelsD4625 Test Method for Middle Distillate Fuel Storage Stability at 43 C (110 F)D4629 Test Method forTr

32、ace Nitrogen in Liquid Hydrocarbons by Syringe/Inlet Oxidative Combustion and ChemiluminescenceDetectionD4809 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Custo

33、mer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.D7566 182D4865 Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel SystemsD4952 Test Method for Qualitative Analysis for Acti

34、ve Sulfur Species in Fuels and Solvents (Doctor Test)D4953 Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)D5001 Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator(BOCLE)D5006 Test Method for Measurement

35、 of Fuel System Icing Inhibitors (Ether Type) in Aviation FuelsD5190 Test Method for Vapor Pressure of Petroleum Products (Automatic Method) (Withdrawn 2012)3D5191 Test Method for Vapor Pressure of Petroleum Products (Mini Method)D5291 Test Methods for Instrumental Determination of Carbon, Hydrogen,

36、 and Nitrogen in Petroleum Products and LubricantsD5452 Test Method for Particulate Contamination in Aviation Fuels by Laboratory FiltrationD5453 Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel,and Engine Oil by Ultraviolet Fluoresc

37、enceD5972 Test Method for Freezing Point of Aviation Fuels (Automatic Phase Transition Method)D6045 Test Method for Color of Petroleum Products by the Automatic Tristimulus MethodD6304 Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric KarlFi

38、scher TitrationD6379 Test Method for Determination of Aromatic Hydrocarbon Types in Aviation Fuels and Petroleum DistillatesHighPerformance Liquid Chromatography Method with Refractive Index DetectionD6469 Guide for Microbial Contamination in Fuels and Fuel SystemsD6866 Test Methods for Determining

39、the Biobased Content of Solid, Liquid, and Gaseous Samples Using RadiocarbonAnalysisD7042 Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of KinematicViscosity)D7111 Test Method for Determination of Trace Elements in Middle Distillate Fuels by In

40、ductively Coupled Plasma AtomicEmission Spectrometry (ICP-AES)D7153 Test Method for Freezing Point of Aviation Fuels (Automatic Laser Method)D7154 Test Method for Freezing Point of Aviation Fuels (Automatic Fiber Optical Method)D7345 Test Method for Distillation of Petroleum Products and Liquid Fuel

41、s at Atmospheric Pressure (Micro DistillationMethod)D7359 Test Method for Total Fluorine, Chlorine and Sulfur in Aromatic Hydrocarbons and Their Mixtures by OxidativePyrohydrolytic Combustion followed by Ion Chromatography Detection (Combustion Ion Chromatography-CIC)D7524 Test Method for Determinat

42、ion of Static Dissipater Additives (SDA) in Aviation Turbine Fuel and Middle DistillateFuelsHigh Performance Liquid Chromatograph (HPLC) MethodD7945 Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant PressureViscometerD7974 Test Method for Deter

43、mination of Farnesane, Saturated Hydrocarbons, and Hexahydrofarnesol Content of SynthesizedIso-Paraffins (SIP) Fuel for Blending with Jet Fuel by Gas ChromatographyE29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications2.2 Energy Institute Standards:4EI 15

44、50 Handbook on Equipment Used for the Maintenance and Delivery of Clean Aviation FuelEI 1583 Laboratory Tests and Minimum Performance Levels for Aviation Fuel Filter MonitorsEI/JIG 1530 Quality Assurance Requirements for the Manufacture, Storage and Distribution of Aviation Fuels to AirportsIP 12 De

45、termination of Specific EnergyIP 16 Determination of the Freezing Point of Aviation FuelsManual MethodIP 30 Detection of Mercaptans, Hydrogen Sulfide, Elemental Sulfur and PeroxidesDoctor Test MethodIP 34 Determination of Flash PointPensky-Martens Closed Cup MethodIP 69 Vapour Pressure-Reid Method (

46、St-B-9)IP 71, Section 1 Petroleum ProductsTransparent and Opaque LiquidsDetermination of Kinematic Viscosity and Calculationof Dynamic ViscosityIP 123 Petroleum ProductsDetermination of Distillation Characteristics at Atmospheric PressureIP 154 Petroleum ProductsCorrosiveness to CopperCopper Strip T

47、estIP 156 Petroleum Products and Related MaterialsDetermination of Hydrocarbon TypesFluorescent Indicator AdsorptionMethodIP 160 Crude Petroleum and Liquid Petroleum ProductsLaboratory Determination of DensityHydrometer MethodIP 170 Determination of Flash PointAbel Closed-Cup MethodIP 216 Particulat

48、e Contaminant in Aviation Fuel3 The last approved version of this historical standard is referenced on www.astm.org.4 Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR, U.K., http:/www.energyinst.org.uk.D7566 183IP 225 Determination of Copper in Light Petroleum DistillatesSpectr

49、ophotometric MethodIP 227 Corrosiveness to Silver of Aviation Turbine FuelsSilver Strip MethodIP 274 Determination of Electrical Conductivity of Aviation and Distillate FuelsIP 299 Determination of Bromine IndexElectrometric Titration MethodIP 323 Determination of Thermal Oxidation Stability of Gas Turbine FuelsIP 336 Petroleum ProductsDetermination of Sulfur ContentEnergy-Dispersive X-ray Fluorescence SpectrometryIP 342 Petroleum ProductsDetermination of Thiol (Mercaptan) Sulfur in Light and Middle Distillate FuelsPotentiometricMethodIP 354 Determinat